You're not asking the right question so you won't get an answer. I am asking the right question, but maybe you did not understand it properly. It's not a pharmacy or chemistry lab. An error of 10% is totally fine and acceptable. If someone would said "I have measured 7,2W" and someone els...

I really don't know what's the point of your question, but if you are so interested it's about 95-98% idle (2-5Mbit in+out average) to 2-5% busy (day average).

What I wrote above is my definition of idle device, for the purpose of measuring power consumption.
Performance I need is full 1Gb routing with firewall, VPN and many many parallel connections.

Hi What is the idle* power consumption of L009UiGS-2HaxD-IN? I have a setup where the device is locked in a small (4U) 10" rack cabinet, without ventilation. Previously I used RB2011 (I need a few 1Gb eth ports and 2,4GHz wifi + ext. antennas) and it worked fine, with acceptable temps, but the ...

Great, I like your solution!
Yes please, post some photos.

Hi
Is it possible to simultaneously power the CRS326 from DC jack and PoE-IN (ether1)?
Will it work like it has two PSUs? -> PSU redundancy.

Hello, I had interesting issue today, and it possibly is a bug in NTP. I wonder if anybody had similar effect. Exactly ad 02:00 am (UTC 00:00 +02:00) 5 of 9 CCRs in my network hanged. The boards aren't the same type, and also the software is different (from 6.20 to 6.29.1). They are also located in ...

Hi
Where can i download the newest MIB file? (NstremeDual OIDs included)?
I would like to graph NS2 parameteres using Cacti for example.
Regards

Hmm but as you wrote earlier, in 3.5 card version there is simple 2Ghz offset, so if you set in MikroTik (for example) 5700 freq then you get 3700 real?
Am i right?

Hi, Does anyone have a frequency mapping table for XR3 Card? (all versions) It would be nice to stick it for a while on the forum. I've found only a part of it on the forum: There is a difference between the 3.5 XR3 cards and the 3.7 version for part 90. The 3.5 cards are a 2ghz offset and the 3.7 v...

tomswenson, do you have full freq mapping table for these cards?

It still can be used as a radio repeater / transmitter

Hi,
Ok thx for advice, i wonder what is the cost of a single part.
Can you also tell me something about Atech ATPL-046ALN? I've found no datasheet about this one.

Hi
I have old good RB523 but with broken ethernet port (PoE one). The problem is that the device do not boot using netinstall (using ports 2 or 3). Booting from CF is also impossible. Is there a way to rescue the router? Or do i have to repair a broken eth port?.
Regards

Hi Has anybody tried to configure MikroTik BGP to act as an peer to OpenBGPD Route Server (transparent AS)? I must say i've been working on it for few days now and still i get the same error: route,bgp,error UPDATE message error: route,bgp,error Attribute Flags Error Interesting is that in my case Q...

is Transparent AS working in MikroTik?
If not, are You planning to add thins functionality?

After some research i think i know what is the nature of the problem - transparent AS, is that feature supported by MikroTik?

Hi
I'm trying to set a BGP session with one of my ISPs but the following error occur all the time: Another peer is working without problems.
MT 3.11 x86 Intel
Any ideas?

Try switching from "Ping and SNMP" to "SNMP" in "Downed Device Detection" in Devices section.

Hello, my question is as in topic. In MT 2.9 it was easy: How to do the same in MT 3.x ?

Hello,
Have You managed to find the source of problem with template?
Regards

Hi
I have replaced the file but it made no differences.
I can give You access to my Cacti and server, please contact me for details.
MikroTik versions: 2.9.29, 2.9.49, 3.0 (x86 and mips)

The problem was one missing file from template. Now queues and wireless client are OK, but registration table still not. When i run the querry manually it returns nothing, but snmpwalk -c cacti -v 1 1.2.3.4 .1.3.6.1.4.1.14988.1.1.1.2.1 returned correct data: SNMPv2-SMI::enterprises.14988.1.1.1.2.1.3...

Hi I have installed package on my cacti but it doesn't want to cooperate :( When i have added a host, Cacti displayed: http://img406.imageshack.us/img406/3797/cactierror2nn0.th.jpg Nothing but SNMP Interface Statistics. Of course on MT there are some Queues (simple and tree) and some wireless client...

Hello, I've been doing some experiments today and noticed RB333's strange behaviour with 2 bridged EoIPs. Configuration was like that: Bridge1 : {EoIP1, EoIP2, wlan1, ether1} + some Filter rules related to EoIPs When i enable in /interface both EoIPs, system restarts every 1-2 min. With one EoIP eve...

Hello What should i do to get masquerade working? It's propably something very simple but i can't figure it out. My config is very simple: ether1 (internet) - no IP vlan1, children of ether1 with IP 192.168.0.2/28 ether2 (lan) - IP 10.0.0.1/24 I would like to get network 10.0.0.0/24 masq. and outgoi...

Hello,
Where can i find list of all functions that Dude can handle ? like function 'oid', 'oid_column', 'round' etc. ?

I woluld like to round some number to - for ex. - dwo digits after dot, like 12.45 or 98.32 The Dude shows numbers with 6 digits after dot. Is there any way to do this ?

Regards.

Hello, what is the best way to do such thing: Configuration: addresses on 'Lan' interface are 10.0.0.0/16 and for ex. 212.212.212.212/27, I have made simple queues for every client: add name="xxx1" target-addresses=10.0.2.3/32 \ dst-address=0.0.0.0/0 interface=lan parent=none direction=bot...