Hi there, on a mikrotik router with Router OS 7.12 stable I have following situation: ehter1 = WAN1 ether2 = WAN2 ether3 = LAN1 192.168.1.1 with DHCP ether4 = LAN2 192.168.2.1 with DHCP ether5 = LAN3 192.168.3.1 with DHCP I want to have separated DNS-Server for each LAN, if possible. But I cannot sa...

hi ho, as you can see here https://mikrotik.com/product/RB750Gr3#fndtn-specifications your device has a MT7621A CPU inside. The feature you are searching for is "hardware offloading". So the traffic is switched in switch-chip and doesnt go through the cpu. here you can see what hardware-of...

Hi ho, if VLAN is the only feature you need a CSS is all you need. CRS has also a little router inside, but its cpu doesnt have much power. So its made for some little extra-setups you may need (maybe a wifi controller), but its not enough to route all traffic of the switch through the cpu. for this...

Hi ho, your dns-settings in routerOS seem to be ok. But your router doesnt know how it can reach the DNS-Servers in the internet. So you need to tell him what route (internet connection) it has to take. Go to IP -> Routes -> Add a new route. As Destination add "0.0.0.0/0" and in Gateway en...

Hi there, today over 8 months have passed since swOS 2.12. has beend released and there is still no new version where bugs are fixed? Thats a little bit sad. Not begging for any new features - please just fix the bugs - cant be so complicated. Should it be necessary just go one step back and remove ...

I have 33 pieces of the CSS326-24G-2S+ running and the problem is that after some weeks/months I dont have any access to System and Host in the WEBCONFIG any more. After rebooting they are working fine again for some time. Can you please fix this? I have had the same problem with SwOS 2.11. AFAIK t...

https://docs.microsoft.com/en-us/troubleshoot/windows-server/networking/configure-l2tp-ipsec-server-behind-nat-t-device Thanks for that, but unfortunately it doesnt solve the problem yet. (as DWORD-Value I took "2") - Config export (/export hide-sensitive file=yourconfig) is usually bette...

Hi there, I have an easy setup of a Mikrotik hEX behind a Router FritzBox 7590 as you can see here: schema.jpg RouterOS: 6.47.6 FritzOS: 7.21 The Mikrotik router is to be the vpn server (L2TP IPSec) and I am trying with the win 10 built-in-vpn-client to connect to the vpn server. So I did a Port-For...

https://wiki.mikrotik.com/wiki/Manual:Interface/Bridge#Bridge_VLAN_Filtering Thank you, that helped me to find the solution. For others with the same problem: Similar / additional information can be found here: https://wiki.mikrotik.com/wiki/Manual:Bridge_VLAN_Table https://wiki.mikrotik.com/wiki/M...

Hi there, I have a CRS354-48G-4S+2Q+RM with Router OS 6.47.4 and I need to setup some VLANs. Normally I do that with bridged VLAN-Interfaces, but on this device the CPU is too weak to support 48 GBit/s-Ports. So I am searching for a solution using hardware offloading of bridged VLAN ports. I found t...

1. what that led color meaning? https://wiki.mikrotik.com/wiki/Manual:PoE-Out#PoE-Out_LEDs red blinking seems to indicate a short circuit. 2. is RB760igs support to powering ubiquiti nanostation m5? (i already read the spec about power both of them, and i think it supported each other. 1A 24V) i th...

Hi biomesh,

just wanted to show that I have instantly build a serial cable mac gyver style ;-) And you will not believe it: it worked!
I could connect to console and set boot os back to routeros.
Now everything works fine! :-)

Thank you very much!

If you have a console cable, you should be able to see the Routerboot menu and use the backup bootloader or choose other boot options. https://wiki.mikrotik.com/wiki/Manual:RouterBOOT Thank you for this hint - I dont have such a cable yet, but I can get such a cable if this is a solution that defin...

Hi there, I have a new CRS354-48G-4S+2Q+RM and it was preinstalled with routeros. To have an easier setup I wanted to use SwitchOS on this device. So I started winbox -> went to System -> Routerboard -> and then went to Boot OS and selected "Switch OS" and rebooted. Since that reboot I can...

Problem solved!

I had to add a static route on the server:
192.168.1.15 = IP of Bridge in Mikrotik-Router over ether 2/3

Hi there, there is an easy setup LAN as you can see here: Zeichnung1.jpg Now I try to add a second internet connection only for server backups to a specific cloud host as you can see here: Zeichnung2.jpg lets say cloud host has IP: 111.222.333.444 Mikrotik-Router: ether1: 2nd internet gateway ether2...

Hi there, just go in winbox to "IP-> Addresses" and give eth1 and eth2 an ip address in the specific lan. when there are no firewall rules you dont need to do anything else. It just works, because a router routes! Go to "IP->Routes" and there you will find dynamically builded rou...

Hi there, thx for your replies. You were right! I sniffed some packets and could see via wireshark that the Protocols are STP, MNDP, CDP and LLDP. So - I must say that I dont have much knowledge about these protocols but as far as I could read here https://wiki.mikrotik.com/wiki/Manual:Interface/Bri...

Hi there, I have installed a brandnew RB4011iGS+RM with RouterOS 6.45.5, and after 1 day of operation it got a system hang. There are several LANs configured using 2 WANs and during system hang nobody didnt get connection to anywhere. I then connected a laptop directly to the router, but the the rou...

Hi there, I have the problem on my CCR1009 that packets are send permanently on all VLAN-Ports with 424bps. mikrotik1.jpg As you can see in the picture all VLAN-Ports of SFP-1 are affected. In the next second the same transmission happens on all VLAN-Ports of ether3 and ether4. This happens alternat...

Hi muetzekoeln, thx for your help! all problems "solved". curious thing: I have two "hAP ac" devices that I want to connect to hEX PoE: device1 on 3m patch cable did not work (I tried several times and with different versions of routerOS). Putting device2 on 3m patch cable works!...

Hi there, I have a hEX PoE (RB960PGS) and I want to use the PoE-OUT on several ports. The device is brandnew and comes with factory software 6.40. When I use the DC IN Jack with 24V / 2,5A power supply and plug in a LAN cable to eth1 and connect from winbox I have an poe-out error message "shor...

Hi there, for a little WiFi-Network I would like to set up 3x "hAP ac" devices and supply them with power via POE. I looked up that the hAP ac needs passive POE and has a max power consumption of 17W. As a router for backend and power supply I found the "hEX PoE". In the descript...

I was thinking this was possible with PCQ but I do not want to share the Max-Limit bandwidth, I want every user to get the specified amount of bandwidth.
Is this possible?

Why dont you use simple-queue for each client with max-limit = 2mbit/s.?

Hi there, the situation: German Telekom ADSL-Connection via Mikrotik RB750Gr3 with PPPoE (modem draytek vigor 130) connection: Upload: round about 500kbit/s, Download: 6.000kbit/s. Voip-Telephone using Audio Codec 711 SIP-Port 5060-5076 RTP-Port: 5004-5020 Setup: Mikrotik: ether1 = Internet-Gateway ...

Thank you for the deep explanation, but I will not able to handle it on the mikrotik. I just want to forward all ports from 192.168.1.101 to the internet. The 192.168.1.101 is the real gateway (firewall and linux router) for the LAN. But you should be able to handle it on Mikrotik. Mikrotik is not ...

Hi there, it doesnt matter if you get your wan-ip via dhcp or if it's static. The idea of a DMZ is to separate the LAN in 2 pieces. LAN1 is your DMZ. That is a separate LAN, where you connect servers that need to be reachable from the internet (like webservers, mailservers etc). If somebody hacks yo...

hello there, I have a little problem with separating 2 subnets from each other totally. The setup: RB750GL ether1 = internetgateway ether2 = company lan ether3 = vlan10 with company lan and vlan11 with guest wlan. there is bridge1 with vlan10 and ether2 there is bridge2 with vlan11 only i want bridg...