bump

bump

this should definitely help

Hello Community, I have 2 WANs (2 pppoe accounts, each have its own local address and gateway) Both are from the same ISP. I have both WANs loadbalanced and have PCC (2/1 and 2/2) and failover (routing) and are going through a bridge called "Bridge-Local". WAN1's gateway is x.x.x.x (local ...

deleted

Hi You can to that with mangling. In mangle:prerouting, route-mark all all packets for port SSH (tcp:22) (or any other port you might be using), with some mark. Next step, make sure you have a route over desired isp with that routing-mark. See https://wiki.mikrotik.com/wiki/Policy_Base_Routing, wrt...

If WAN2 for whatever reason (ISP problems) goes down do you want everyone to go to WAN1 for backup purposes? This assumes wan1 and wan2 are not from the same provider, if they are you can disregard this question as both would be not available in the case of ISP failure. Thanks for the reply! That's...

Hi there! I hope I can get a clear answer on this one. So far I haven't found any guide or question about this before (as to my keyword knowledge in searching). Let's say i have: WAN1 PPPOE (ISP1) IP: 10.10.10.10 (normal internet access) WAN2 PPPOE (ISP2) IP: 11.11.11.11 (normal internet access) is ...

If you would want to prevent the existing sessions from breaking, you would need an x86 or CHR running as a virtual machine somewhere in a data center, create tunnels between your home Mikrotik and the one in the DC via both your uplinks, and use OSPF to control the failover between the tunnels. In...

Hello! is there a mikrotik device that allows me to insert 2 simcards and have a 4g/LTE connection and if so, here's the case: I'm looking for a way to be able to switch from SIM1 to SIM2 without any downtime. meaning I don't want browser downloads let's say to fail or pause forever and stuff like t...

+1 For WireGuard

problem solved seems that the ISP locked both accounts on the same MAC address thats why i'm getting disconnected whenever i try to enable both PPPOE interfaces still i used a switch to make each PPPOE go onto different eth port on the router board then i used PCC Loadbalancing as @Chupaka suggested...

If some config is not working - post that config with basic diagnostics (not just 'connection timeout', but ping/traceroute). We're not telepathists. Hello friend, sorry for being late as i was testing every possibility.. nothing is working at all unfortunately. please just look into the export bel...

ether3 and ether4 are different ports =) moreover, you have different pppoe interfaces this will work. just try. i tried exactly what the guide/example says, i ofcourse changed IPs accordingly, but still i'm not able to get them merged and btw i'm getting conn. time out when enabling both PPPOE int...

https://wiki.mikrotik.com/wiki/Manual:PCC#Application_Example_-_Load_Balancing or, for the start, you may just try /interface pppoe-client set [find] default-route-distance=5 /ip route add gateway=PPPoE-Out1,PPPoE-Out2 it will balance equally, but problems with secure websites may appear thanks for...

i'm facing this issue and no one answered on my thread.. likely to be the same question

viewtopic.php?f=2&t=126233&p=621209#p621209 but on different ports

Hello guys, I've subscribed for two internet accounts and the ISP gave me two different credentials to put in a PPOE client. i have RB951G-2HnD that have the following setup /interface bridge add name=Bridge-Local protocol-mode=none add name=Bridge-UPLink protocol-mode=none /interface ethernet set [...

@docmarius
@normis
thanks a lot it worked!

The device is a switch already out of the box. Ports 2-5 are switched. Just plug your cables into ports 2-5 and it will work as a switch. thanks for the reply, i've plugged in the ISP cable on ether1 and the tenda on ether5 ( i haven't configured anything my self, all were default settings came wit...

Set ether1 as the master port on ether2-ether5.

that didnt work but thanks

i already played around with the switch tab in winbox but nothing worked

Hello, may i know if its possible to make the router to act as switch? what i mean by switch is as follow: i have one ISP account i have one cable from my ISP and its going directly to my Tenda11N router. it can only connect by providing the PPOE credentials other than that it cant connect. i have r...

i solved the graphing thing. all you have to do is not to set the limits to unlimited.
and concerning the redirect thingy nevermind about it i can go with it.
thanks

Hello Mikrotik Community! this is my first post and i'm really hoping you guys can help me out with this issue. i know i should use web proxy or accounting or traffic flow... but i'm pretty beginner so if some of you could post briefly instead of posting links to manuals because i've surfed them ton...