Need some information about the RBwAPR-2nD&R11e-LTE:

Can it be setup for:
- 2 lte connection to differents apn active at same time
- send and receive sms from this device
- as ppp-client for dialup connections (ATD+number)?


Anyone as already tried it?

Thank you with redirect I get the proxy web page, but it says Connection Refused. I've tried to add 192.168.254.2:80 in web proxy access rules but it seems ignored, it only seems to work with method:DENY and REDIRECT-TO but it won't load the page. How can client connect from lan x.x.1.x to remote ho...

I've a dialup connection 9600b/s of speed with a remote web server host 192.168.254.2 , my local clients are able to connect to that with nat trought 192.168.1.1 that is the router 192.168.1.10 lan client > connect to router 192.168.1.1:88 that nat to remote host 192.168.254.2:80 if web proxy is ena...

with MTU and MRU of 1500 it takes 2 minutes to load an html page
with MTU and MRU of 576 it takes 1 minutes to load an html page

the speed on the ppp interface is 9600

there is a way to calculate the correct value to set?
still getting Rx Errors and cannot ping the remote host

Dear Sirs, we have a serial modem (CINTERION GEMALTO BGS2T) connected to a mikrotik RB953GS-5Hnt, we are using this as a ppp-client. remote host: 192.168.254.2 local address assigned by dialup 192.168.254.3 [admin@MikroTik] > /interface ppp-client print Flags: X - disabled, R - running 0 R name=&quo...

In wiki dialup page no hardware is mentioned, in supported hardware list, the modem is present, without any note.

Can you please at least say me what's wrong with this question? Netiquette has been respected so why no feedback?

Of course it's a config problem, please give me an hint. I don't know the dialup specification, could it be that dialup use pstn, and the modem doesn't allow it? On the serial modem I can see that the connection command is: ATD<phone number>; Now I've opened a session from > /system serial-terminal ...

I'm using a RG951G-2HND with routeros 6.39.2 I can see the Huawei E173 s-1 USB modem: # DEVICE VENDOR NAME SPEED 0 1:1 Linux 3.3.5 ehci_hcd RB400 EHCI 480 Mbps 1 1:5 HUAWEI HUAWEI Mobile # DEVICE NAME CHANNELS USED-BY BAUD-RATE 0 I 1:3 usb1 0 I can set up a working ppp-client connection with my prov...

Seems to work like this: min@MikroTik] > /interface ppp-client print Flags: X - disabled, R - running 0 R name="ppp-SECONDARY" max-mtu=1500 max-mru=1500 mrru=disabled port=serial0 data-channel=0 info-channel=0 pin="" user="XXX" password="XXXXX" profile=default...

I'm connecting with dialup trought a serial modem, apparently it works fine, but if I remove the option in tab PPP: Add as default route /interface ppp-client add add-default-route=yes dial-command=ATD disabled=no name=\ ppp-SECONDARY password=xxx phone=xxxxx port=serial0 user=xxxx then restart conn...

Just to know this are the results of my tests: model: 2XGNJ - DW5550 REV:A02 DELL > ppp: 3CH: signal error > sms : CMS ERROR 500 model:D15G2 - GCT UDC-AHB Subsystem D > LTE: 4CH: signal Ok Disabled Direct-IP > sms : timeout(6) model:HP un2420 Mobile Broadband Module > not recognized > ppp: modem did...

I'm triyng to installa OpenWRT on this routerboard but get stuck at first step: RouterBOOT booter 3.34 RouterBoard 953GS-5HnT CPU frequency: 720 MHz Memory speed: 300 MHz Memory size: 128 MiB NAND size: 128 MiB Press any key within 2 seconds to enter setup.. writing settings to flash... OK Please, c...

I think routeros is great but not exactly user friendly, please have patience if the question is silly. I've connected a linux box by RS232 to a Routerboard, setup the special login as described in wiki, and accessing trought ssh serial@myrouterboard it works! Now I need a little step over, I want t...

Hi,
any update on this argument?
Did you success connecting to the PLC?

What a nice surprise with the update, I can't believe you can turn off by software the LED of a rasbperry pi and not those of the routerboar.
Black tape, will solve the problem?

Here I am, tried another modem, still can't send or receive sms, looking to understand: - checked the resources: USB2 is detected - checked the signal strength: from ppp-client (is this the correct menu?) What's wrong? Same SIM, same place, in a phone, the signal is good! [admin@MikroTik] > /interfa...

Hi, I've tried also changing the antenna connection on the modem, no change in results. What is causing the timeout error? It's just an sms, I've inserted the sms center number, the serial get used by sms, then timeout error appear... Can someone please help me? Is there a "paid support" w...

Dear Sirs, I've tried to turn off the LEDs on this routerboard, without success. If I set as ALL LED OFF IMMEDIATE return the could'nt change led settings erro. I don't want any LED ON. Is there something special to do to make this work? Thanks, BR /system leds> print Flags: X - disabled, * - defaul...

the sms result is always a timeout, the lte scanner return error what's the problem?
Help, please! thanks, BR

Dear Sirs, still trying to send sms without success, changed SIM, changed modem pci port, nothing seems to change. If I set usb type not as minipicie the LTE interface disappear as the modem on the USB list. If I try the LTE connection the log says online, but it is not, the lte info screen is attac...

The URL seems dead, can you please reupload the files?
or better can mikrotik integrate those driver?
Thanks, BR

Same situation, did you solved this problem?

Thanks for reply, I can see the device on usb tab, but in sms setting can select only serial0, if enable ppp, opening Info view complain that can't reuse channel while ppp-client running! (6) If the devices are show on USB, why should they use serial0? The modem is in the supported device list, what...

Dear sirs, I'm trying to send / receive sms with this config, but I think something is missing: hw: - RB953GS-5HnT - pcie modem: WI-D15G2 - pcie modem: AUX 0168 - 1 sim (slot position should be the same?) sw: router OS 6.38.5 I don't understand if the modems are seen from the routerboard from the jo...