Hello, I use the wAP ac LTE6 kit and the speed is very low. With my smartphone and 4G I reach 80/30 Mbit and with the LTE Modem maximum 40/10 Mbit, mostly only 35/5 Mbit. What can I do, what should I check? It is the same contract. I use the newest Modem Firmware R11e-LTE6_V027 and the newest Long-t...

Hello,

it is possilbe to see when a Identities connect last time? in PPP Secrets is a column with Last logged out.

KR
Oliver

Hello Sindy, I use this device: https://mikrotik.com/product/wap_ac_lte6_kit I see the LTE Modem unter /interface lte, but i cannot select it unter /interface pppoe-client. the Option /port firmware set ignore-directip-modem=yes have I also test, but with a ppp connection also don't work. I think th...

Hello, I have a wAP R ac (arm). I have installed a SIM Card and can go to the internet. Now I use a special Service APN and will start a PPPoE session, but I cannot select the LTE Interface. What can I do to select the LTE Interface? It's a Fallback solution, if DSL is down, i can get the same stati...

Hello, how can I reset an interface automaticly if the interface only transmit packets? If there an other possibility for netwatch and ping? Often I have on some Interfaces ( VLAN, PPP ) that they no received packets, and after reset ( down/up ) they work fine for a long time ( 1 Week or 1 Month or ...

Hello,

I use CRS326-24S+2Q+RM and CRS317-1G-16S+RM with the Software 6.45.7 and with S-RJ01.

If I disable the interface, the device on the other end, don't know about them. There is the link up. On Mikrotik is the link down.

Is this a knowing Issue?

KR
Oliver

Hello,

the Switch has a CPU load from 95% if I connect the cable from the "Satellite Headend" there comes a traffic from round about 700 Mbit.
I don't get a picture on TV screens. I think It is the wrong Switch for this application?

KR
Oliver

It is possible to show the column Version in the Tabsheet Managed?

Hello, I use the switch with Router OS. I have put all interfaces to a bridge, only without the management port. It is possible this port to isolate? ( forwarding override acivate, but no forward to configure ) I don't want use VLAN for the management port. So, it is a valid configuration? Or it is ...

It is over L2TP. The MT1 is the router, that brake out to the Internet, not the MT2.

Hello, I have a problem sending an IP from the subnet outgoing. 1. MT1 is the main Router in the RZ, there is a Subnet routet to an IP, which is on it. That works fine. ( subnet 10.2.3.0/29 ). 2. MT2 is the client Router, connect over the Internet PPPoE to the MT1 and get 1 IP Address ( ip 10.1.1.1/...

No idea everyone?

Hello, I have this problem on some Hardware CCR1009, RB3011UiAS, etc. The PPPOE Session is establisht and work fine for some hours or days. And than the Rx traffic stop working, you don't see any traffic on this. Router OS doesn't notice that, so it has done manuel deactive and active the PPP Interf...

I have a Problem with SFP Kupper Modul from MikroTik. When I plug the modul, the right Serial Number, Part Number and Revsion would be shown. After reboot: Wrong Part Number "S)", no Revision and Serial 00100300. That is not all. If I enable this port, the Switch reboot, and reboot, and re...

Hello, A. Yes, I'm sure, there are no NAT rule which other IPs. Only the /24 ( current /32 ). Additional Information. The Subnet 10.251.0.0/24 is for some L2TP Connetion. At the Moment only for 10.251.0.10 ( only on L2TP ) B. Only one L2TP Tunnel has the IP 10.251.0.10, so no other Device can starte...

Is it possible a bug? I use 6.40.

After I Change from /24 to /32 all logs shows the right Internal IP.
But if I use a second internal IP, what should I do than?

Export file is not possible, there is probability that I Change not all ( Passwords, Preshared Keys, External IP Addresses )

Can I give on other way more informations?

The external IP Addresses are on a VRRP Interface.

Sorry, for my bad english.

Hello, Internal Address: 10.251.0.0/24 External Address: x.x.x.x Online IP: 10.251.0.10 I have NAT a /24 Subnet to one external IP. That works fine for the Online IP. In the Subnet only work/is online 1 IP. I don't understand the Log. 22:35:49 firewall,info forward: in:vrrp8 out:sfp-sfpplus8, src-ma...

Hello,

I have the same Problem. Is there any solution for or don't work like this?

KR
Oliver

It works on different Hardware without Problems ( I don't use all funktions from MT :-) ). But when it is wrong, I will change it. I have another question. I have a public IP range /26. Some IPs I will use on the MT and some on other Systems. If I work with VRRP, how to do that? Should I add all pub...

If you don't use /32s on any secondary IP address (not only VRRP) you will receive broadcast traffic (among other things) twice. This could affect some services and routing protocols. That's also why /32s are always used on Loopbacks, in order to not create a broadcast domain. Whilst MT may create ...

Hello, VLAN works fine on VRRP Interfaces. In wiki stands, I should VRRP Intarface only give /32 not /24. Why should I do this? What is the reason for that? Work for me. - ether1 ( 10.0.0.0/30 ) - VRRP1 ( 10.0.0.4/30 ) - VLAN1 ( 10.0.1.0/24 ) - VLAN2 ( 10.0.2.0/24 ) - VLAN3 ( 10.0.3.0/24 ) What I un...

Hello,

there is High CPU (45%) usage, when the IPSec don't send traffic.

Networking 41 %
unclassified 5 %
total 46,9 %

KR
Oliver

Hello, I have a Problem on 2 CCR1072 with VRRP. IPSec stop working after time X ( 1 day, 2 day, a half day, etc. ) No traffic was send. I have delect all Connections and flush SAs but it don't help. Only a restart work. On the other end is also a Microtik RB3011UiAS-RM I have change the Level in IPS...