MikroTik

mihailJl

Hello, The strategy is: Two site with 2 MT device(hap ac2 v6.49 - ISP real ip , OVPN server AND hap ax2 v7.11 - ISP local ip , Ovpn client) , in the tunnel i connect 2 networks over VLAN20 for Lan network and VLAN10 for IP TV. The problem: And Ok, everything work like a charm - the device in network...

mihailJl

Its Done!
I try with version 7 and login with admin without pass. Then remove admin and created again with no password. Return to version 6.46, and loging without problems!!!
I don't know what happened...!

mihailJl

At the firs the bord was with 6.45.
With netinstall I back up to 6.43..
On the next turn i trayed with 6.48

mihailJl

Hello, Yesterday before I started configuration I did a full wipe. After that, I couldn't login anymore... With Netinstal I tryed with both older and newer versions and still the same. Login attempts were via winbox and web with the following data: User - admin, pass - User - admin, pass - b629-f1b4...

mihailJl

Hello I have IPTV(L2) and Wifi for internet on RB951Ui RB951Ui - eth1(WAN) and eth2-eth3 are in bridge1 - My TV works normal and I use UPT-cable for connection(TV-box1 -> eth2, TV-box2 -> eth3) RB951Ui - eth4,eth5, wlan - are in bridge2 - This is for my internet. But now, I want to remove UTP-cable ...

mihailJl

OK, I change the plan IP-TV site -> Bridge1(ether1(wan),ether2(ip-tv box for other TV), IP-TV-tunnel(EOIP)), Bridge2(ether3,4,5,wlan) Other site ->Bridge1(pppoe1(wan),ether2,3,4,wlan) , Bridge2(ether5,IP-TV-tunnel(EOIP)) I think the connection is success, the traffic on IP-TV-tunnel is 10Mbps consta...

mihailJl

I changed the location of antenna and basebox with 5 meters in back, because there is a airport antenna yagi direct to my equipment around 3 meters.
For now there is no problems...! So strange!

mihailJl

mihailJl

Firmware upgraded too? When you say its beeping, it does that in a loop? Like restarting again and again? If yes, maybe you ve set an IP address in watchdog? Yes, there is beeping loop. Yes there was watchdog, but I already turned it off. I also changed the AC-contact that was behind the UPS. Now U...

mihailJl

Do they work after a reset? Netinstall ?

- > YES

mihailJl

Тhe time is not exactly fixed , maybe after 2 weeks but with all the same problems with different time with the same problem ..! I think, there is an external interference because two meters from my antenna there is a 122MHz yagi antenna with pointing right at mine(I dont know what is the power). Нo...

mihailJl

Hello, I have problem in one wireless link between basebox 5 with (#oct/ 1/2019 9:49:53 by RouterOS 6.45.6 # software id = ZR3Z-YZG9) I revive it every week with netinstall! The problem: It stays in a state where it restarts in 10 seconds(beeping) and not start operating(winbox does not find it)...!...

mihailJl

Hello! My provider is deliver to me internet and IPTV STB Q11. I remove his router device and I put routerBoard 951. I have 2 PC and 2 TV + 2 STB Q11. Now my network work like this -> PORT1(WAN) and PORT2(to switch-> to TV boxs STB Q11) in BRIDGE 1 PORT3,4,5,wlan,eoiptunel in BRIDGE 2 (with DHCP) to...

mihailJl

Everything is done!
I have some rules in firewall that block my connection!

mihailJl

A have no access to this two web sites: https://bazar.bg/ and http://www.speedtest.net/ ....! My ISP is use PPPOE! RB951 6.42 My options are: 1 bridge -> ether2,3,4 + wlan + EOIP copy/pase this mange rule and everything is fine, THANKS pe1chl !! But would you like to explain what exactly does it do?...

mihailJl

Network setups with EoIP interfaces: Possibility to bridge LANs over the Internet Possibility to bridge LANs over encrypted tunnels Possibility to bridge LANs over 802.11b ' ad-hoc' wireless networks As you know wireless station cannot be bridged, to overcome this limitation (not involving WDS) we ...

mihailJl

Hello I have this scenario: RB1(ip:10.0.0.1)(dhcp-client:192.168.0.2/24(PC)) is connect by EOIP to RB2(10.0.0.2)(dhcp-client:192.168.1.2/24(TV(sony bravia-smart tv) ) ) I want to cast from my web browser PC to TV! From PC I have success ping to network 192.168.1.1 but to TV my ping is "time out...

mihailJl

My question is : How can i see the IP address from where experiments are being done?
Can I see it or not?

mihailJl

I have massage in my log with this critical error:
login failure for user admin via bandwidth-test

How can I see the IP address who make experiments?
I have only open winbox service!

mihailJl

Thanks Sindy its work perfect!
And only i want to ask about the firewall NAT, why it is needed? I try without it and It works again.

mihailJl

20180521_094156.jpg This is my scenario! I want to transfer files from PC1 to PC2! Pinging TEST: PC1 to: R1,R2,Cloud, 8.8.8.8 is success! PC2 to: R1,R2,Cloud, 8.8.8.8 is success! PC1 to: PC2 is unreachable! What is the practice of putting these computers on the same network in this scenario? Thanks!

mihailJl

I want to get "Uptime" in variable and compare!

:local uptime [/system resource get uptime]
:log info $uptime
:if ($uptime > ..... ) do={
:log info "yes"
} else {
:log info "no"
}

Maybe the variable is in string and the compare is not success!
How to convert?

mihailJl

OOOooo Sory!
My mistake I forgot to check printers configuration. The gateway was wrong!

mihailJl

my network is 192.168.0.0(server) on one side and 192.168.1.0(client) in other side.
When I try from server site office to client office there is no problem, but inversely i have only ping to the printers?

mihailJl

I have site-to-site vpn - ovpn!
I have problems with printer access to printing!
The ping is success but i have no access to connect and printing?
Any suggestions?

mihailJl

On my ruter I have Load Balancing in two WAN ports - WAN1 WAN2 In my network hava a six computers that choice the best way(WAN1, WAN2) to connect to defined target in web! I want preroute one of the computers to use only WAN2. I think I managed to do it success, but I'm not sure that it's right? In ...

mihailJl

The net: mikrotik ->ether 1 and 2 WAN , ether 3 to switch(DHCP1), ether 7 to router tplink for wifi (DHCP2) Details: After non stop work(16 days), the router Mikrotik lost DHCP2 internet conection. Tplink had no access to internet. Tplink had access ping only to WAN1,2 gateway! I try to connect to t...

mihailJl

I looked a lot on the Internet but I could not find a solution!
Мy goal is to create a white-list with webpages(https and http) to
to access successfully.
And everything(https and http) else to drop/reject it?

mihailJl

Thanks! I reviewed for PBR and I try this in my scenarie: ip firewall Mangle add chain=prerouting src-address=192.168.0.0/24 action=mark-routing new-routing-mark=ThroughOnly_WAN2 Ip Route Add Dst-Address=0.0.0.0/0 Gateway=y(ip gate) Routing-Mark=ThroughOnly_WAN2 ip firewall nat chain=srcnat src-addr...

mihailJl

I have two WAN connection and two LAN connection.
WAN1 - > x
WAN2 - > y
LAN1 -> 192.168.0.0/24
LAN2 -> 192.168.1.0/24
Also I have load balancing...
But I want LAN2 to use only WAN2 connection!
How can i do that?

mihailJl

ohhh the problem was complex.... Slow internet upload from 1 side and external usb Lan modul with virtual machine in the other side...! Naw I brought out in physical environment and the everething is normal 3.5MB! My next step is to connect new PC with OPENVPN soft! 20170728_214308.jpg.ac8da28c31941...

mihailJl

Now set up SSTP to try and the same situation. 280kb... https://www.youtube.com/watch?v=DmfN8HMJ06I

mihailJl

Okey the connection is success! Now the problem is the speed. The transfer betwen to computers is 280kb???

mihailJl

Okey now i try Open VPN ! I use this article http://paulswasteland.blogspot.bg/2015/05/site-to-site-openvpn-using-mikrotik.html but the client side has error - termination-TLS failed but on the server side TPC connection estabilished from .... 1 - I synchronized the time 2 - I executed the following...

mihailJl

Okey its Done, Thanks! :) Next question! Will I be able to build a VPN between my Mikrotik in DMZ and another Mikrotik at another distant point? I found this https://www.youtube.com/watch?v=oR4G6SZ3LcM material that pretty well explains network building and settings. If I take it as an example if it...

mihailJl

Thank you!
Later I will try and write!

mihailJl

The problem is the following... Occasionally the user loses the internet! His status is connected but there is no internet! I noticed that in PPP-> Active Connections(cloud core router CCR-1009-8G) this user is connected with two different IP. When I remove it and next connection everything is norma...

mihailJl

Hello yesterday you bought a 951ui-2hd router. I've seen a lot of videos and read a lot of articles, but I'll need extra help too!

My first task is to access It from an external network! pic
Some guidance?

Search found 38 matches

RDP over ovpn(L2)(Site-to-Site) not possible

Re: LHG 60Ghz after reset - wrong username or password..

Re: LHG 60Ghz after reset - wrong username or password..

LHG 60Ghz after reset - wrong username or password..

Wireless bridge for IP-TV and Internet together in one WLAN

Re: IPTV-STB Q11 on Bridge Mikrotik

Re: MT Basebox 5 stop working and restart every 10 second

Re: MT Basebox 5 stop working and restart every 10 second

Re: MT Basebox 5 stop working and restart every 10 second

Re: MT Basebox 5 stop working and restart every 10 second

Re: MT Basebox 5 stop working and restart every 10 second

MT Basebox 5 stop working and restart every 10 second

IPTV-STB Q11 on Bridge Mikrotik

Re: Eoip cast TV

Re: Can't access one website

Re: Eoip cast TV

Eoip cast TV

Re: Login failure critical notification

Login failure critical notification

Re: Access to PC's in separate network with 2 routers [SOLVED]

Access to PC's in separate network with 2 routers [SOLVED]

Get Uptime from Router in number

Re: Problems with printing through VPN (Solved)

Re: Problems with printing through VPN

Problems with printing through VPN

Route users on defined WAN

Internet problem in DHCP server

White list web-pages

Re: port targeting with two WAN

port targeting with two WAN

Re: Setting the mikrotik 951ui-2hnd

Re: Setting the mikrotik 951ui-2hnd

Re: Setting the mikrotik 951ui-2hnd

Re: Setting the mikrotik 951ui-2hnd

Re: Setting the mikrotik 951ui-2hnd

Re: Setting the mikrotik 951ui-2hnd

OpenVPN connection fail, one user with two ip

Setting the mikrotik 951ui-2hnd