So, what were the EXACT steps? What did happen? What did You expect? These three points will make far easier to debug the problem. Just in case, problem report standard litany reference: http://jdebp.info/FGA/problem-report-standard-litany.html I think my description so far on how to reproduce and ...

If you refer to my comment, there is no step to be taken for reproduction.. it just happens continuously after power on! The question "how to reproduce" can be translated as: "please, tell me the EXACT steps in order to make it happen on my system". There is a logic behind it: w...

how to reproduce?

If you refer to my comment, there is no step to be taken for reproduction.. it just happens continuously after power on!

We updated from 7.15.1 to 7.15.2 to several RB760iGS units. We have activated the "allow incoming requests" to the DNS server of each device, as it is used by local clients for name resolution. Since the upgrade, we have been noticing the DNS service to stop responding to requests from cl...

We updated from 7.15.1 to 7.15.2 to several RB760iGS units. We have activated the "allow incoming requests" to the DNS server of each device, as it is used by local clients for name resolution. Since the upgrade, we have been noticing the DNS service to stop responding to requests from cli...

We'd like QSFP28 ports on the switch side instead of QSFP+ or QSFP+ ports instead of QSFP28 on the router side so that we can utilize the full available bandwidth (40G or 25G), however the "mix and match" between the two seems to sacrifice performance and lock the maximum available speed ...

100G QSFP28 is backwards compatible with 40G QSFP+, so they should connect at 40G using the Q+85MP01D or equivalent (at 4 lanes of 10G instead of 4 lanes of 25G, same fallback as SFP28 -> SFP+, which is 1 x 10G instead of 1 x 25G). I read the first mentioned article before posting, however it menti...

Hello to All, We are looking the alternatives to connect 2xCCR2216-1G-12XS-2XQ units with multiple CRS354-48G-4S+2Q+RM units. CCR2216-1G-12XS-2XQ has 12x25G QSFP28 ports and 2x100G QSFP28 ports CRS354-48G-4S+2Q+RM has 4x10G SFP+ ports and 2x40G QSFP+ ports One of the 100G ports in CCR2216-1G-12XS-2X...

Yes, inter-VLAN firewaling will still work without "use-IP-firewall*" options set. Performance difference should not be great though ... note that if you have those options set to yes, only traffic handled by CPU will be affected anyway. As long as HW offload is active (involved ports hav...

Thanx for the quick answer @mkx! So, in other words, if I remove VLAN filtering within the bridge for the two different subnets (LAN/WAN) but still use VLANs to distinguish the traffic per ethernet port, the IP firewall rules as defined will continue to work? Do I understand it correctly? If this is...

Hello, I have two CRS326-24G-2S+ bonded together via a couple of trunk interfaces in a typical WAN<->Internal LAN scenario (RouterOS 6.49.1). As the two networks (LAN/WAN) need to be separate, in order to take advantage of RouterOS HW bridge capabilities, I used a single bridge and the associated VL...

Exactly the same as in my case, which I described in a post earlier! The ARM unit (cAP AC) keeps on disconnecting from CAPSMAN whereas the MIPS one (cAP Lite) is, by far, stable! Just read your earlier posts and you mentioned massive resource consumption (which I cannot see directly; maybe it only ...

That makes four of us as I have described in an earlier post within this thread, probably since the cAP AC shares the same architecture & CPU with hAP ac2 ... By the way, the Mikrotik support ticket I have opened is SUP-51317 Still suffering here. Meanwhile I have some indications what happens ...

That makes four of us as I have described in an earlier post within this thread, probably since the cAP AC shares the same architecture & CPU with hAP ac2 ... By the way, the Mikrotik support ticket I have opened is SUP-51317

Hello to all, I had posted this https://forum.mikrotik.com/viewtopic.php?f=21&t=174403#p858443 regarding excessive resource consumption using firmware 6.48.2 and the ARM architecture (specifically cAP AC when using CAPSMAN). Unfortunately, the same behavior is still observed with 6.48.3.. as a r...

Hello to all! I've been using 6.48.2 for a while now in my small home business network, based on a RB760iGS as a master router and CAPSMAN manager and two access points, one cAP AC (RBcAPGi-5acD2nD) and another one cAP Lite (RBcAPL-2nD), both as CAP Clients. All devices have their firmware upgraded ...

But yes, you might be limited by 500mah max output on POE out. 500mah on 24V, and some loss in cable will be be a bit under 13watt which you say the device has as max consuption. If this is the case, a psu with higher voltage for Hex S will solve it. Thanx for the input. I'll try to test it somehow...

Have been using Hex S with cAP ac (powered by the Hex S) for some time now...without any problems. I would first check cable, what exact cable is in between the two? Can you try with a short patch cable in between? I have tried with 3 different cables straight out of the box, 2m or smaller, to no e...

Hello to all, I own a Hex S and I power it up with the 24V/1.2 A power supply (RouterOS 6.48) included in the box. I tried to attach a cAP ac unit to the #5 Ethernet Passive PoE port of the Hex S, which provides a 500mA max output (i.e. 12W under 24V). The Hex S has a maximum power consumption of 6W...

Found the issue!!!! I had defined the following CAPSMAN Rates within my configs: 0 name="test-rates" basic=12Mbps supported=12Mbps,18Mbps,24Mbps,36Mbps,48Mbps,54Mbps ht-basic-mcs=mcs-0,mcs-1,mcs-2,mcs-3,mcs-4,mcs-5,mcs-6,mcs-7,mcs-8,mcs-9 ht-supported-mcs=mcs-0,mcs-1,mcs-2,mcs-3,mcs-4,mcs-...

As long as you can connect to AP swithout capsman, I'm inclined to believe something is missing in your capsman setup. Can you post an export (with hide-sensitive ofcourse) of your running config on capsmanager? Also a verification of the status on one of the running cap-interfaces vould be nice. (...

Hi quackyo, I have exactly the same wireless setup, that is a separate VLAN for IoT and a virtual SSID for all IoT devices. I run the AP system to the frequencies you mention, paying particular attention so that adjacent APs have no overlapping channels as well. I am not using any extension channels...

Hello to all! I have been using ESPhome firmware (1.15.0) with a multitude of devices that are based on either ESP32 or ESP8266 (e.g. WeMOS D1/D1 Mini). The wireless network is provided by Mikrotik Access Points, including the model RBcAPGi-5acD2nD and RouterBOARD cAP L-2nD ones (all running firmwar...

with the well-known Mikrotik wireless coverage and performance issues Nonsense...it's more difficult to configure MikroTik Wifi (and router as well), I don't have any issues. I mentioned that I have performed many Miktotik installations, most of them with 2-figure APs. This does not mean however th...

Hello to all, I own one cAP AC (RBcAPGi-5acD2nD r2) and one cAP Lite (cAP L-2nD). They were working as independent APs until now (different SSIDs among them) with the well-known Mikrotik wireless coverage and performance issues. They are both running RouterOS 6.47.1. As I live in a two storeys house...

Hello, I can confirm the same behavior regarding the build-in SNTP server and the firmware change to 6.39.1 and 6.39.2 from 6.38.x. The Routerboard model is 2011UiAS with firmware ar9344 v3.33 We are syncing the Routerboard with a server and we use it as a time server to time sync other devices atta...