Done... FW upgrade via serial was the way to solve this...

Hi all: i have some issues trying to do a netinstall to a RB800, just after the disk is formatted, the terminal console shows this: Oops: Kernel access of bad area, sig: 11 [#1] ] RB800 NIP: 8018e50c LR: 8018e5e0 CTR: 8018b040 REGS: 8f9dbbd0 TRAP: 0300 Tainted: P (2.6.27.39) MSR: 00029000 <EE,ME> CR...

thanks!!!

i have "Link XXX" added as port of bridge1 and wds-default-bridge=bridge1

what does this message mean???

13:35:59 wireless,debug Link XXX: failed to set bridge port for Link XXX, reason: device already added as bridge port (6)

well... i have some issues with RB600 +XR5 +XR2... on normal day operation the XR5 link works normally (i dont remember signal strength right now, but is -in 60 to -75 range), but suddendly at nights the signal strength goes down near to -90, until 5 or 6 am, goes back to normal operation. this is n...

i try with hex all 1's... but no with ascii code...

i'll try it...

thanks!!!

Update:

40 bit wep (1111111111) not linking...
104 bit wep (aaaaaaaaaaaaaaaaaaaaaaaaaa) not linking....

same error

Hi all: i am trying to connect a RB133C with RoS 3.0RC11 to a Teletronics "CPE Router", when i do this without WEP encryption the link is operating correctly... but when i put WEP in both sides i got the next log message: Association failed: unspecified (1) the Teletronics "CPE Router...

hi all: i think this is a kinda newbie question.. i have a RB133C connected to an AP with no WDS support, it is something like this.. Internet<-----------> AP <~~~~~~> RB133C <--------------->PC Wired Network Station mode Wired Network AP IP 172.45.99.1 (Wireless Router) Station IP 172.45.30.9 (The ...

hi all... can i perform a RouterOS Downgrade from RoS3.0 to RoS2.9.x in the RB333 board?? if this is possible... do i would expect something bad like license lost or something whatever can be bad or everything will be normal?? how can i do that??? if it's not possible... 1) could you help me with th...

hi all: i have a RB532Ar5 with RoS 2.9.4x (i don't remember the RoS exact version right now), in this equipment i have the next wireless configuration (working config)... Wlan1 (Xr5) = Station WDS with default bridge bridge1 Wlan2 (SR2) = AP bridge with no WDS (their clients do not support WDS {Tele...

sorry for the delay thom... well.. the replacement is done, lab test as you suggested run very well... when we go to relplace the original AP, we got some difficulties, but we did the rigth config on the remote clients and the connections go up... we got some high ping times, but we replace the omni...

First - I believe that your LS connected because you have a policy of default forward and default authenticate set up for your RB532 (in the future I'll just call it an RB). In Winbox this can be seen in: Wireless tab on the left hand menu. Select the interfaces tab. Now select your wireless card. ...

thanks for your comments Thom. first of all, the "TT CPE Router" that i am trying to replace is the same product that you mentioned before... and this operational mode is in access point mode (Not routing. simlpy AP mode). I have used TT EZBridge CPEs w/MT 532s. It will work. I am not sure...

Hi all!! we are trying to repalce a Teletronics CPE Router with a RB532A... CPE is working only as an AP. WEP encryption, this AP have a 20 Client between Teletronics EZBridge and Litestation2. CPE Router = 250mW 802.11b Omni 15dBi TT EZBridge = 200mW 802.11b grid 24dBi LS2 = 400mW 802.11b Panel 19d...

http://img237.imageshack.us/img237/1630/ejemploredqk5.jpg There is the diagram.. What i need to know is how should i configure to use GW1 instead of GW2 for internet access. i can use DHCP server but i need static IP to get a better control of my RB532. i'm going to replace another RB532 in a remot...

Thank you for your help andrewluck!! that information helped me in some way... i hope you can help me with this case... i have a network with two IP ranges ( there is no routing tables into it, so if i want to interact with these networks at the same time i have to add two static IP entries to my ne...

Hi all: I am a newbie with RouterOS using as a router, i have some experience using it as a Wireless Networking Device. but now i want to know what i need to know to configure RouterOS as a internet router, what protocols do i need to understand completly well. i hope you can help me with it. is the...