Actually, this ended up being from loss of comunication between the routers due to one of the routers constantly rebooting due to cold weather. That is why "state changes" only counted on one side.

Was there ever anything found on this? This problem just popped up on a link that's been good for quite some time. both running RouterOS V4.13 (Power Router 732s). Just wondering before I head out there tomorrow to change ports to see if that helps.

Still, an absolutely awesome home or mom/pop business router for a mere 40 bucks.... you get TONS of capabilities! Why only mom/pop business? We have RB450 devices, which we installed before the RB750 came out and has similar specs, at offices with dozens of workstations. By mom/pop business, I was...

Can you run a throughput test of AES256 encrypted IPSEC tunnel on each version? :D I just completed this test, mainly because of our experience with the RB493AH lockups. I wanted to see what they could do. about an even 1.65Mb up and down with both- 3des AND 256AES. Still, an absolutely awesome hom...

We are not using any wireless cards. We connect to Trango BHs and Canopy APs at the tower sites. Configuration is from default settings for most, and some upgrades from RB600s- both having the same issues.

Thanks,

OK, I think my problem is gone. Here's what I did... I rebooted multipule times and it would still only boot when hitting the front button. Then I lowered the cpu freq down to 600- multiple failed boots- 400- multiple failed boots- 300 - multiple failed boots- 200 BOOTED! After rebooted about 20 tim...

I have sent the information to Mikrotik support. I will post any info I receive for the record-

ok, so I can get in the console now, (yeah, my fault- cable sais X, but wasn't). This is as far as it gets and stays there forever RouterBOOT booter 2.20 RouterBoard 493AH CPU frequency: 600 MHz Memory size: 128 MB Press <delete> key within 5 seconds to enter setup..... loading kernel from nand... O...

This started when I upgraded a routerboard from 3.26 to 3.27. When I upgraded the OS, I also upgraded the firmware to 2.20 (I believe it was 2.18 before that). Everytime I tried to telnet with the "system telnet" command, the router would lock up. I would have to reboot it multiple times t...

Just wanted to add our experiences..... We are having a very similar issue. We have RB493AHs that we have been using since it seems we cannot get daughterboards for the RB600s (which have had NO problems for us on probably 30 towers or so). We are experiencing the port lockups, but even more, about ...

This is NOT a "routing" problem. It is a problem with autonegotiation between the Routerboard(s) and the switch(es). I have experienced same problems with (many) RB 493 AH and RB 433 AH. After some time and without serious traffic load, suddenly only the Tx seems to work, while Rx is stuc...

Actually, this problem was from an encryption problem- without encryption it works fine.

did you find a solution to this???

I have the same problem with a power router running V3.13.....

Hello,

I was wondering if anyone had any info about when there would be new daughterboards for the rb600 available? We have used the 564 with no problem, but everyone is out of stock on them now. Any info is appreciated- Thanks.

One other thing.... the response time on my Mikrotiks are absolutely horrible. This seemed to just start happening today.

Today my wireless interface went down. It is 2.4 Ghz AP in bridge mode to the ethernet. It has been running good for some time now (about a year). When I logged into the Mikrotik, I found that there was NO "R" next to the wlan interface. I remember this actually happened to a back-haul onc...

I have done much reading and will try testing with the following in mind. "don't forget to disable "Change TCP MSS" to "no" in pppoe profiles and set one firewall/mangle rule that changes TCP MSS for all pppoe users to such as 1300" I will try this with the following su...

Thanks for your help, much appreciated- worked great.

Hello, I have found that on certain versions, I try to upgrade via the web interface and when I hit upgrade it reboots, but no changes have been made. Still running the same version. I've noticed that when I slowly increment up the versions it works fine. 2 questions please: 1. Is there a way where ...

any ideas at all?

any ideas?

name="pppoe" local-address=10.0.0.1 remote-address=pppoe-2-only session-timeout=0s idle-timeout=10m use-compression=default use-vj-compression=no use-encryption=default only-one=default change-tcp-mss=default rate-limit=1500/1500 incoming-filter="" I'm going to give this a test r...

ok, I have the two servers up and both have seperate pools to assign. they took all the connections fine but I noticed that it was assigning one ip for the user, and one for the local interface (sub-interface I suppose) for that connection. I saw that as when I looked into ip routes, I found that th...

So, you are saying that if I have the service name the same, they will load balance? that would mean I need two seperate pools on each server correct? or will they not assign duplicates if they have the same larger pools on each? The reason I ask is, I would like each to have the capability of runni...

Hello all. I am rather new to the mikrotik thing, as you would probably know... I am changing out the pppoe servers in production right now. I won't be doing PPPoE at this time on the APs, just changing hte pppoe server here to mikrotik. the server is 2.0 celeron with 256mb ram. (I hate celerons, bu...