You can use Routing - BGP - Network. Add your network and un-check 'synchronize'.

what does synchronize do?

It depends if your iBGP routes are originated within your own AS; or do they come from a different AS??

they come from different AS

Dear all, I am about to create an RTBH server where it is used for blackholing an IP address in case of DDoS attack. I have implement my topology with Cisco products where they were in charge of BGP. In my new case, I am running BGP on ccr-1036. One of my design requirement is, NOT installing certai...

hi everyone
what is this warning?
snmp warning timeout while waiting for program 44

thank you all
if ( give me some solution to findout this)
else (thank you to)

Those below the Mikrotik should be Access Ports, not Trunk Ports

my servers are in multiple vlans
each server have at least two vlans

It's still not clear to me what you want to do. Anyhow ... VLAN settings are supported on Mikrotiks. You can make VLAN settings per port: access port meaning ingress untagged, egress untagged, has default VID or trunk port meaning ingress and egress tagged or mixed - ingress and egress tagged but i...

i want config ingress and egress on mikrotik switch for entire vlans which tagged 20,21,22,23 negotiate to separate interface

Someone can post something about mikrotic switching such as tagged and untagged vlans?

Hi, i have fixed it by adding the following lines: /ip firewall filter add action=accept chain=forward dst-port=123 protocol=udp /ip firewall nat add action=masquerade chain=srcnat dst-port=123 protocol=udp src-address=hotspotnetwork Important: You have to place the rules in front of the dynamic ho...

hello to everyone i have two ip-ip connection to my service provider which one is main through the fiber and the other is failover link through wireless connectivity my destination ip in each tunnel have same ip and source ip in each tunnel have different ip i want when fiber link get down , connect...

/system health print show you results
write that in terminal and feedback here

you connected cisco and mikrotik in same subnet so what do you need to nat?? your inside subnets on cisco side reach to mikrotik and in mikrotik in the routing table added and in firewall you can manage any connection that which ip reach to which one in other way if you connect to mikrotik through t...

what is wireless mode on ap and station?

hi
you can set bypass on ip binding

do you add packet mark on simple queue??

does it work in v3 snmp ?? i done your way i saw the graf in prtg but information of temperature was empty I use SNMP v1 and it works, you have to divide the result by 10 to obtain °C celsius. thank you so much i tested that in v3 and worked as you say i divided the results by 10 to obtain `c

hi everybody
i have a question
is it possible in mikrotik routers set them to work as active-active ??
i have two core router and tow distribute switch connected with each other full mesh for stability and i want act routers as active-active

thank you

Hi Friend, I want to connect all the ap through Ethernet cable with the switch. So why WDS! Sent from my iPhone using Tapatalk wds gives you a mobility connection , wireless cloud , stability user up time in all area of wireless network if you dont want play with WDS you can set similar config in e...

you should set a filter rule to access the lan ips
when you connect to vpn you are in router but dont reach the lan ips
you should set access to what ip you want reach with filter rule

if you wanna do everything in mikrotik for medium scale this router (RB2011UiAS-RM) is good and you can establish the internet connection in router to access remote through the internet and when you established vpn or eoip can reach the router through eoip or vpn and you can use different ip in both...

hi mikrotik man yeah this is posible right now with a beautiful feature that called WDS on wireless you connect 4 APs together and replicate with each other and you see one ssid actully right now or you can use a capsman feature on routeros there are two way ,depend on you which way you like do goo...

hi mikrotik man yeah this is posible right now with a beautiful feature that called WDS on wireless you connect 4 APs together and replicate with each other and you see one ssid actully right now or you can use a capsman feature on routeros there are two way ,depend on you which way you like do goo...

please explain more what you want

my question is , does mikrotik device get temperature information to prtg ?? and if it get to prtg , how it work? Yes, you can get temperature, voltage, and so on via SNMP. Just obtain the correct OID with: [admin@xxxxxx Router] > /system health pr oid active-fan: .1.3.6.1.4.1.14988.1.1.3.9.0 volta...

creat an address-list for ips that you dont wanna block
so in the rule in src/dst-address-list choose that and press the checkbox in left of address-list that means NOT
with this config you block all ips except the ips you want

you should handmade the users which kind of users wants to access some sites or not solution of this way is creating a address-list which one of them manage block section and the other one manage access section ----------------------------- chain : forward src-address-list : block-users layer7 : ......

have you internet access by cable at modem?? you give internet to router and want pass internet to your lan network with wireless interface step1:you set ip to wireless interface step2:set dhcp on wireless interface step3:masquerade the subnet of wireless IP this is a solution for your problem that ...

hi
if you wanna watch the camera from internet
your configuration steps :
chain:dst-nat
dst-address:public-ip
dst-port=80
action: dst-nat
to address:dvr-ip
to port : dvr-port

you can set any address to local address, no problem you can set local address sam as remote address ,this way is secure because when client connect via vpn to your network , he/she couldnt see your ip address that set on router or interfaces remote address is a address that you wanna serve it to cl...

hi mikrotik man yeah this is posible right now with a beautiful feature that called WDS on wireless you connect 4 APs together and replicate with each other and you see one ssid actully right now or you can use a capsman feature on routeros there are two way ,depend on you which way you like do good...

hi everyone
i have 4 mikrotik device such as 3 ccr1036 and 1 crs 125 in network structure
i wanna monitor the tamperature of mikrotiks on prtg
my question is , does mikrotik device get temperature information to prtg ??
and if it get to prtg , how it work?
thank you all