MikroTik

unlimitedme

Thanks SurferTim, it work like a charm!
i cant believe a simple default route is mandatory.

unlimitedme

so you mean to say, if i add the ip default route
then any external network will be able to ping that public address?

i have contact my isp, they said they only able to ping that ip from the gateway's ip address.

i will add the default route, and let you know the result.

unlimitedme

Hi SurferTim, as requested [admin@MikroTik] > /ip route pr Flags: X - disabled, A - active, D - dynamic, C - connect, S - static, r - rip, b - bgp, o - ospf, m - mme, B - blackhole, U - unreachable, P - prohibit # DST-ADDRESS PREF-SRC GATEWAY DISTANCE 0 ADC 111.XX.YY.ZZZ/30 111.XX.YY.ZZZ ether1 0 [a...

unlimitedme

HI, I just bought a RB450G, remove the default configuration (bridges) and put the ip public address in eth1, then connect it to a switch where my ISP radio were plugged. however, i could not ping that ip public address from any external network. i do not setup any firewall rule. I use RouterOS 4.16...

unlimitedme

cybernet,
Thank you for your post, yes i am using unmanageable switch, so i want to overcome this situation.
I do not understand about your post,
If you have same situation, maybe you can post what you have accomplish.
For now, we are using EOIP.

Do you have other solution?

Thank you

unlimitedme

cybernet,
What you said is just an ordinary way to bridge two network over wireless, and that was not my question.
Thanks anyway for your post.

unlimitedme

jorj, I will try to use EOIP then, i will let you know the result. onnoossendrijver, Interesting, i will see if we can bridge EOIP with a VLAN. Diganet, Why use managable swith, if we can elaborate it with MikroTik? wpeople, we have minimal ethernet port resource on the AP and the client, so i am lo...

unlimitedme

wpeople,

how to create multiple wds for each client?
please take a look at my updated picture.
thanks a lot for your kind reply

unlimitedme

Normis/Janis/Everyone, Please help... I have try to draw my scenario, please give me advice. I am using RouterOS 3.11 on both radio clients and Access Point radio http://img295.imageshack.us/img295/1249/vlanvg6.jpg Please advice, any reply will be highly appreciated Thank you note: i updated the pic...

unlimitedme

meno, i think your case is similar with my case. can you tell me, how many progress that you made? i have try the following: on client radio: bridge port : vlan from ether , vlan from wlan on router A behind client radio: bridge port : vlan from ether1, ether 2 but the connection between client radi...

unlimitedme

hytanium, Thank you so much for your reply... I am not quite sure about the wds bridging. What do i need to use as default bridging in the wlan for each network ? Because there is only 1 wlan on the each side of the radio. [Router A,B,C]**via LAN cable**[Client]~~~via wireless~~~[AP]**Via Lan cable*...

unlimitedme

please help anyone?

unlimitedme

QpoX, Thank you for your reply, i have read those thread before. but those thread use multiple interface wlan. My situation is like this: [Router A]**via LAN cable**[Client]~~~via wireless~~~[AP]**Via Lan cable**[Router B] on Router A: 2 ether on Client (routerboard) : 1 ether, 1 wlan on AP (routerb...

unlimitedme

Dear all, i have been trying to create a multiple VLAN connection over an existing wireless link, but every time i create a VLAN, and add the existing WLAN interface to VLAN, then the wireless connection will be broken, and disconnect. The reason i do this, because i have multiple router behind the ...

unlimitedme

sergejs/normis/janis,

please help...

unlimitedme

knock knock, anyone?

please help...

unlimitedme

Dear All, I've changed the ip firewall conn track value into this: ip firewall connection tracking> pr enabled: yes tcp-syn-sent-timeout: 1s tcp-syn-received-timeout: 1s tcp-established-timeout: 1d tcp-fin-wait-timeout: 5s tcp-close-wait-timeout: 5s tcp-last-ack-timeout: 1s tcp-time-wait-timeout: 1s...

unlimitedme

still no response from mikrotik team......

normis/janis ? please help...

unlimitedme

gmsmstr,

well, i'm sure many people out there having this issue as well and hopefully i'm not the only one that post about it.
i hope mikrotik support would listen about this issue.

unlimitedme

same with me.

knock knock...any info from sergejs or normis?

unlimitedme

gmsmstr,

yes, i hope so. Because this motherboard was already out on 2007.
Thanks

unlimitedme

thanks gmsmstr.

normis, i have send the supout.rif, hopefully it will be added on next release.
thank you.

unlimitedme

normis,

where should i send the supout.rif?

unlimitedme

i attach some screen shot from resource window

the Mikrotik recognize it, but it doesn't show on interface list

unlimitedme

Dear maximan,

the chipset is 10/100Mb Attansic PCIe LAN.
Do Mikrotik not support this chipset?

thanks

unlimitedme

to normis and everybody,

i'm using pc as my router machine, the motherboard is ASUS P5GC-MX, the new Mikrotik 3.3 still can not detect driver for my on board ethernet LAN card.Please help...

thank you

unlimitedme

chupaka,

i'm on it..

unlimitedme

normis,

how about indonesian? (bahasa) ?
may i do it?

unlimitedme

sergejs,

can this scenario being applied in a bridge wireless networks?

thanks

unlimitedme

normis right, the new 532 series was already at 400Mhz.
for the old ones, you can try overclock it.

unlimitedme

For enterprise system, the money was not the issue,
Service Level Agreement and QoS that matters the most.
But, for small-medium company system, usually they think more about cost reduction.

Either way, it proves to us that our Mikrotik can run for every type of company.
So, why bother arguing it?

unlimitedme

uptime limit=1h and credit with time equal to 1w

unlimitedme

well, i havent find a way to differentiate the user queue for local or oversea in usermanager.
It's just one queue for the user.

unlimitedme

knock,,knock... anyone?

unlimitedme

i am very confuse with your setup,
NATing with bridge???

unlimitedme

JJCinAZ, i have setup a routed network, it's like this: Network A (10.1.5.0/24) | | Router A (mode=station) | | Router B (mode=ap-bridge) | | Network B(10.1.2.0/24) the direction is from network A to network B, the link was ok, it shows connected. - how to forward all network A, so network B can see...

unlimitedme

IMHO,
it is better if you use some power surge protector, rather than make it "sleep".

unlimitedme

@warwick09, thanks for replying. actually i was only wanted to create a routed network, since bridging allows my client to see each other network, and they tend to mess with other's file/folder. example: ISP (ether1=10.1.1.254) | BOX1(wlan1 = 192.168.10.1, ether1=10.1.1.1, mode = AP)---client1 | | c...

unlimitedme

dingram,

have you try changing channel?
It might be the interference from other wireless antenna around you.

unlimitedme

hello everybody? please help...

unlimitedme

Dear Gunzoid,

so it means, only AP - station mode right?
and how about protect each client, so they can not see each other?

unlimitedme

avisdel,
if you wanted to link 2 different networks,
try to use bridge interface.

unlimitedme

CMIIW,
as i know, you can assign a specific queue for ICMP or ping packet, so it wont get stuck at the same queue.

try it if you like.

unlimitedme

Dear Znuff, thank you for your reply! yes it is, that is what i am trying to create. -how about the wlan mode? on Box 2 (client), i set the wlan as station-wds mode and on box 1(ap), i set the wlan as ap mode. and i am not doing any bridge port, or create any bridge at all. - i am also wanted to pre...

unlimitedme

Hi all, I have manage to bridge different network and same network, but recently i have been reading about routing network. The objective now is the mikrotik box can act as router not switch anymore (today it was using bridge interface between each box). Is this possible? or i am just day dreaming? ...

unlimitedme

stuntshell,

what do you mean by looking the table of each network segment?
please explain in config.

thanks

unlimitedme

- you were running ppoe-client on public interface?
- can you print out the route?
/ip route print

unlimitedme

downloading via ICMP?
please explain it.

unlimitedme

Dear balimore,

do you have example VLAN on wireless network?
Thank you so much

unlimitedme

sorry balimore,
i am not clear enough, it was station-wds mode on each client router.
the problem is, network client B and C can see each other,
they were supposed to only see their network only, not other network.

any idea? as i am still a noob on mikrotik.

Thank you

unlimitedme

dear all, to make all of you clear of my network, MAIN GATEWAY (NETWORK primary - AP Bridge) || || WDS || || ROUTER A (AP Bridge)----WDS------ROUTER B (Station) || || WDS || || ROUTER C (Station) - Is it have to do with masquerade each network B and C? - so the client behind the router can not see e...

unlimitedme

mneumark,

thank you for your reply.
How to use VLAN on a wireless network like i have?Can you give me a hint?
I have read the manual about VLAN, but it does not show any example for wireless.
Please help.

unlimitedme

Guys, I have these kind of networks, Network A has 2 physical interface, as Access Point -ether1 (10.1.1.250/24) -wlan1 (mode = ap-bridge) -wdsbridge1 (192.168.10.253/24) Network B has 2 physical interface, as Client1 -ether1 (10.1.2.250/24) -wlan1 (mode = station) -wdsbridge1 (192.168.10.252/24) Ne...

unlimitedme

hello friend,

please see this document:
http://www.mikrotik.com/testdocs/ros/2. ... reless.php

unlimitedme

mneumark,

may i have your setup configuration please?
i'm doing WDS now, and i wanted to try your setup.
thank you

unlimitedme

how much tx/rx the rate?
any significant increase compare with wds?

unlimitedme

thanks, i have got it work and running.

unlimitedme

Does those client connect to the same base station?

Never try it though,
how about create queue for each client mac address ?

unlimitedme

In theory,
if you bond those 2 physical interface, you will get about +40MB,
but in reality, it will drop to 50%,
try to use Nstreme2, maybe you will get better performance

unlimitedme

i'm kinda confuse with your setup, maybe you could explain it better, 1. set wireless side A with ap-bridge mode, and side B with station mode, correct? 2. do not create bridge port, correct? 3. side A: Ether1 = ISP ip address (public) WAN1 = 192.168.70.1/24 (private) a router with IP: 192.168.190.0...

unlimitedme

Chris, would you mind email me those app too? (unlimited_question2004 at yahoo dot com)
thx a lot

unlimitedme

Hello all, i'm a new members in this forum, i have been reading the manual and succesfully create WDS between 2 network. Network A: ether1: 10.1.1.252 wireless-bridge: 192.168.10.252 Network B: ether1: 10.1.1.253 wireless-bridge: 192.168.10.253 My question are: - How to NAT the network behind each r...

Search found 62 matches