MikroTik

sojicmk

I have pppoe problem with same router except I do not have NAT. It can connect with WRT54G2 over PPPoE on another provider, but can not connect to Mikrotik. After "sniffing" the network here is the result protocol: PPPoED version... code.... sessionId... payload length = 0c (12 decade). Ot...

sojicmk

By the way... the server is HP Prolian ML 110G5

sojicmk

Yes, I just set ./system hardware set multi-cpu=yes... still same.

Should I restart the server?

sojicmk

Where can I set multi-cpu=yes?

In System->resources there is CPU Count = 4

sojicmk

gmsmstr: where we can buy this hardware?

sojicmk

Chupaka

Sorry, what is your question?

sojicmk

Is there 64 bit version of Mikrotik? I have Xeon, Quad core, 2.4 GHz and CPU usage is about 60%. Also there is 4 x 1Gbit lan, and users can not use them more then 100MBit.

As I say... there is about 1000 active pppoe users.

Can somebody help me to improve the speed?

sojicmk

Yes, Radius server response to mikrotik for rate limit.

There is speed limitations and trafic measuring for each pppoe user.

sojicmk

Any response?

sojicmk

Xeon, Quad core, 2.4 GHz - 1000 pppoe users, using around 100mbps - CPU usage around 60% I think that maxiumum will be around 1500 pppoe users on this configuration. Can we "tune" this and increase number of users (or decrease cpu ussage)? I need 5000 users (in the moment) using around 3gb...

sojicmk

I have 2 types of clients. All "log in" over pppoe, but... Some of them have public IP addresses.... some are over NAT and have private IP addresses. I want this scenario: 1. Client connecting over pppoe, get public IP. That's all. He have internet 2. Client connecting over pppoe, get priv...

sojicmk

Both MT are PPPoE servers connected to same Freeradius.

IP assigning is not problem, problem is how to "route" 80.x.158.0/24. Clients behind MT2 should get public IP (80.x.158.y)

I try to do that, but routing was problem (pppoe clients can not ping MT1)

I will try again later.

sojicmk

we have two mikrotiks: Internet peering IP: 88.85.x.2/29 Aveable IP classes: 80.x.157.0/24, 80.x.158.0/24, 88.85.x.0/24 So... I want to "add" another mikrotik behind this and want to "assing" 80.x.158.0/24 class to it. How ti set up routing? The "main" (the first one) m...

sojicmk

Few days I have problem with authentication with freeradius 2.1.3 Here is details Listening on authentication address * port 1812 Listening on accounting address * port 1813 Listening on proxy address * port 1814 Ready to process requests. rad_recv: Access-Request packet from host 10.20.30.4 port 51...

sojicmk

So....

I have routeros (as pppoe server), RB433AH (as access point). How to "bridge" wireless "incoming" connections to pppoe server?

sojicmk

I upgrade it to 2.9.51, but now use 100% CPU.

Here is details:

CPU: Intel 3 GHz
PPPoE 300 tunels

On another MT i have 300-400 PPPoE Tunels, Intel 2GHz with CPU Usage 50%

What is the problem?

Same configuration, but the first one (with 100% cPU usage) have 1GB Lan cards.

sojicmk

I use Mikrotik as PPPoE server (with freeradius) but... I use 1Gb lan cards, and I think that because of that this happens: After few minutes, link (to ISP) fall to 0, after few seconds, it back, but problem with memory start. When memory become 0, routeros restart itself. I think that images are en...

sojicmk

How to limit internet access to clients which are not from DHCP or PPPoE?

So....
Mikrotik is PPPoE and DHCP server, but if somebody set manually IP address, and set gateway IP of Mikrotik he will get internet access.

How to limit internet access only to DHCP or PPPoE clients?

sojicmk

I need something like on http://wiki.mikrotik.com/wiki/Load_Balancing_over_Multiple_Gateways (that is first part), and... If ISP#1 fall all workstations which used ISP#1 to "switch" to use ISP#2. Is it possible? So.... if ISP#1 and ISP#2 are OK it should be: C:\>tracert -d 8.8.8.8 Tracing ...

sojicmk

Currently I'm using PPPoE+Freeradisu.

Is it possible to use DHCP+Freeradius, and how should "look" records (in radius DB) for authentication?

sojicmk

The problem was firewall.

Sorry

sojicmk

I just install DUDE and I have problems: Computer IP: 192.168.0.x (assigned from VPN server) VPN server: 192.168.0.x and Public IP: 88.85.112.x Mikrotik ROS: 88.85.123.x I can access to internet and Mikrotik (from Winbox), but.... Dude can not ping out from local network. It discovered local network...

sojicmk

If I use rate limiting I will limit all the traffic.

I want 2 types of limits. It is not so simple just to use rate limiting.

sojicmk

How to set simple queue from radius?

sojicmk

No, it is not wireless.

It is pppoe (lan).

sojicmk

I have MT as pppoe server with freeradius. I want to limit internet speed, but also I want to DO NOT limit speed to few IP classes. I do it with simple queues. For each client IP I have simple queue (and mangle, to "separate" internet and "local IP classes") I have around 500 use...

sojicmk

Is it possible (an how) to detect does client sharing conection?

So, clients connection via pppoe and is possible to share connection. How to stop this?

I have some information that it is possible with setting TTL to 1, but I need details.

sojicmk

sojicmk

I had the same problem with upgrade.

sojicmk

May be because I have a lot of firewall definitions and it use processor.

sojicmk

I do not think that it is hardware problem because as speed go up, CPU also go UP. So.... if the speed is limited on 20Mb and 400 PPPoE users connected CPU usage is around 60%. If the speed is more, CPU usage is 100%. I think that it is normal (because firewall have to "process" more data)...

sojicmk

This is my network: mikrotik.gif I start FTP transfer (3Gb file) from WEB server 1 to WEB server 2. The speed was around 60Mbit/s and after few minutes mikrotik crash. PPPoE clients can not connect. I have to restart Mikrotik. When I create rule in queues to limit the speed to 20Mbit/s it is OK. Why...

sojicmk

I have mikrotik as pppoe server which "check" usernames from freeradius.

How to lock username with mac address?

sojicmk

1Gb cards are SMC (realtek chipset).
1G switch (24x100Mb + 2+1Gb) also SMC

sojicmk

I have this configuration: Mikrotik 2.9.4x with 3 interfaces 1 - link to the internet 2 - web server + radius server + pc 3 - pppoe clients It works perfect, till 3 days ago when we change 3 interfaces with 1Gb lan After few minutes pppoe service crash. In log I see "peer is not responding"...

sojicmk

So, I'm using free radius. Does free radius support netFlow?

Any other client which support netflow?

sojicmk

Any hints about this? How to implement this?

sojicmk

Any comments?

Is it possible or not?

sojicmk

I have mikrotik with 3 packages (differents speed and bandwidth). For each speed I have defined IP pool and assign IP's for: Package 1 = xx.xx.xx.10-xx.xx.xx.30 Package 2 = xx.xx.xx.31-xx.xx.xx.90 Package 3 = xx.xx.xx.91-xx.xx.xx.200 I have limited speed in simple queues. Speeds are limited for outs...

sojicmk

Yes, I get log in memory, but nothing on Syslog server.

I'm using PortPeeker for listening. Also I'm developing my syslog server (Delphi).

sojicmk

Same problem.

I want to log pppoe logins and logouts. I set remote loging but I do not receive nothing on the syslog server.

sojicmk

I have Mikrotik RouterOS. Clients connecting by pppoe and get IP from DHCP server.

Is it possible to "connect" DUDE to Mikrotik and "show" status of pppoe clients?

So....

In Dude, I want to "add device" but to specify pppoe username, not IP address.

sojicmk

Is it OK?

First to mark all p2p then internet connections or, I have to mark internet connections then p2p?

What will be in first what in second case?

sojicmk

Skontao,

Znaci u markiranje internet konekcije trebao sam da "izbacim" p2p?

P.S. Kako si znao da sam "nas"?

sojicmk

The user with IP xx.xx.xx.184 should be limited to download with 512 but he download with about 1678 http://www.dalibor-sojic.info/images/mikrotik/torch.gif / queue simple add name="184" target-addresses=xx.xx.xx.184/32 dst-address=0.0.0.0/0 interface=all \ parent=none packet-marks=interne...

sojicmk

/ ip firewall mangle add chain=prerouting p2p=all-p2p dst-address-list=!Lokalni action=mark-connection \ new-connection-mark=p2p_conn passthrough=yes comment="" disabled=no add chain=prerouting connection-mark=p2p_conn action=mark-packet new-packet-mark=p2p \ passthrough=no comment="...

sojicmk

Scenario: I have xMB link I want to limit local users to: 1. Local traffic - unlimited 2. Internet traffic - 512/512 each 3. P2P applications - 128/512 all Is this configuration OK? / ip firewall address-list add list=Lokalni address=88.85.123.0/24 comment="" disabled=no / ip firewall mang...

sojicmk

Clients connecting over PPPoE and get public IP 88.85.123.x I want, but I can't, to set limits: Packet 1 - 256/256 Packet 2 - 512/512 Packet 3 - 1M/1M Local trafic (between users and local servers) unlimited or 2M. I tried this: queue simple add name=Packet1 max-limit=256k/256k queue simple add name...

sojicmk

@ravin

I want to use radius server, but I do not know how to install and "connect" mikrotik to radius.

I have PPPoE users. I want to:

Limit speed

Limit Bandwidth

Decrease the speed after Bandwidth

How to do this?

sojicmk

I need limiting also, but.... I have 1MB didicated. Users connectiong over PPPoE. I want to limit user1, user2, user5 with 256/256 user3, user4, user7 512/512 userX, userY 1024/1024 How to do this? Also, I want to use RADIUS server, but I do not know how to "connect" pppoe server with radi...

sojicmk

It is OK now.

I just unplug and plug again the lan cable.

But, why I could not connect by FTP???

sojicmk

I have mikrotik as router.

Clients connecting by PPPoE.

At the moment I am connected by PPPoE and I can not connect to any ftp server, even on mikrotik.

Search found 52 matches