MikroTik

Acryli

Hello My RBM33G + LTE card is configured with an IP Passthrough. In other words, the router is somewhere else and the RBM33G acts as simple modem. The problem is that in such a configuration RouterOS doesn't seem to have internet connectivity. How do I give internet connectivity to the RouterOS with...

Acryli

In my setup it works well (AC3-LTE + EM160) ... the only problem is that after reboot modem connects to network but "session uptime" is empty and while it empty connection does not work. After I reset (disable and enable) LTE interface it starts working well without any problem Ok I will ...

Acryli

Ok, when I try to change the APN profile I also get that error "5G not supported". So I assume that I don't have internet connectivity because the APN settings aren't correctly sent to the EM160R by RouterOS. Same problem with RouterOS 7.2 stable release. I will try with older ones. I'm a ...

Acryli

Hello I installed RouterOS v7.2rc7 on my RouterBoard. I updated the firmware of an EM160R to the last version EM160RGLAU R02A09M4G because of the reboot bug, without testing the EM160R before unfortunately, so I'm not sure if the problem is the firmware or not. Now I 2 issues. 1. I can't get any int...

Acryli

Hi, I just realized that recent Quectel modems like EM120/EM160R and some 5G model already have a eSIM chip soldered on the module. https://forums.quectel.com/t/em160-esim-procedure-guide/10134/6 https://i.imgur.com/He2sVCa.png I understand that Mikrotik still doesn't support it natively over comman...

Acryli

When I noticed this in one location, I thought it was because of the poor LTE signal (it's a remote location). But then I installed another device which is roughly 300m from the tower, and got the exact same result. Also, this is with two different network operators, and my iphone can achieve signi...

Acryli

Thank you very much for the photos :) Well the heatsink seems to be composed of 2 parts, so there is a way to do a custom thing :) Do you have a better photo of the PCB? I wanted to check the traces that goes to the M.2/mPCIe to see if it's USB 2 or 3. Yet one last question about the gain pattern in...

Acryli

Hello I have some questions about the new LHG G LTE. https://mikrotik.com/product/lhgg_lte6_kit#fndtn-gallery It has an cat6 mPCIe modem. If I buy the LHGG I would probably want to change the mPCIe modem with an M.2 one. But since it has a huge front heatsink I'm asking me some questions. 1. Is the ...

Acryli

Thanks SiB Well I will have to check the USB mode of my EM12, because SMS and cell-monitor does not work on my configuration. About the IP passthrough, it works, but I facing an annoying bug. If the IP of the internet connection changes (dynamic IP), my real router (Ubiquiti) stay the old IP. I don'...

Acryli

Thank you very much SiB, your contribution to the forum are very useful.
It works indeed. :-)

Yet another question (if it's the right place)

Is it normal that the cell-monitor doesn't work with an EM12?
Same for the SMS transmission/reception feature? (maybe I have the wrong settings)

Acryli

**** FIRST SETUP **** Set Connection Modes AT+QCFG="usbnet" <- Query current mode AT+QCFG="usbnet",0 <- QMI/PPP/Default - usbX device with ppp-outX - IgnoreDirectIP=yes AT+QCFG="usbnet",1 <- ECM - works at ROSv6 as lte1 interface as module NAT addressation 192.168.225....

Acryli

Hello I have some difficulties to configure my RBM33G with an EM12 LTE modem running under RouterOS v7b8. I'm getting an IP address from the LTE provider, but no internet connectivity, although the APN is configured correctly. I'm using the same APN settings on my phone and it works. So I'm missing ...

Acryli

Hello I only wanted to ask if the Quectel EM06 LTE modem are fully supported (AT commands, LTE monitor,...) by RouterOS 6 or v7 and if it also support IP Passthrough ? (I know there is support for the EP06 but I haven't found any info about the EM06 although it's exactly the same electronic on board...

Acryli

Had the same issue with an EM7565 and v7b8.

Acryli

Hello I have a RBM33G with 3 Ethernet ports. https://i.imgur.com/RJdu286.png ether1 is used as IP-passthrough (LTE) and connected to a WAN port of my Ubiquiti router. There is also a management vlan on that ether1 interface. Now I wanted to use ether2 and ether3 in the same IP range as my other devi...

Acryli

Hello I was testing my EM7565 LTE modem with an USB 3 adapter on a RBM33G Routerboard with RouterOS v7b8 but I have some issues. The modem gets detected, but I get the error that the sim card is not present. I don't know why this error happen, because I have tested the same modem with the same adapt...

Acryli

+1

Same problem with an EM7565.

Acryli

Hello

I needed to know if RouterOS v6 or even v7 supports USB 3 controller as minPCIe card? Does RouterOS include the required driver?

For instance card based on Renesas D720202 controller (PCIe -> 2x USB 3):

Thanks

Acryli

Up

I still have the same questions about the EM7565 support but also for the Quectel EM20-G and Quectel EG12 present in the new "Mikrotik Chateau LTE12"

Acryli

Acryli May I ask you the gain pattern of the mANT LTE 5o LTE antenna. https://mikrotik.com/product/mant_lte_5o#fndtn-specifications The radiation pattern would be interesting too, but since it's an omnidirectional antenna, there is probably nothing special. All u.FL are GLUE then those two are not ...

Acryli

Thank you for the information !

Acryli

Hello I wanted to ask which DB9 serial port to USB converter cable I could buy on ebay/ali to connect to the external DB9 serial port (male!) connector of a Routerboard. Most of the serial converters I find on ebay use a female connector too. But I assume a basic male-male adapter won't work because...

Acryli

Hello

May I ask you the gain pattern of the mANT LTE 5o LTE antenna.
https://mikrotik.com/product/mant_lte_5 ... ifications

The radiation pattern would be interesting too, but since it's an omnidirectional antenna, there is probably nothing special.

Thank you

Acryli

What I'm seeing is that it will connect to either band 12, 17 or 2 primarily, and only sometimes if the primary is band 2, it will show 2CA with band 5 but then drop right back up. That's actually the normal behavior of any LTE modem. The carrier aggregation channels are only used on heavy load, af...

Acryli

Thank you for your answers

Acryli

Ok thank you.

Acryli

Hello I read on a different forum that RouterOS 7 beta finally supports the Sierra Wireless EM7565 CAT16 LTE modem. Now I have several question about it: 1. LTE interface or PPP (=slow)? 2. Does it work with USB2/3 connectivity or is PCIe also supported in RouterOS7? 3. Does bridge mode (IP passthro...

Acryli

Hello I wanted to ask if the LtAP LTE (RBLtAP-2HnD) supports VLANs (RouterOS 6 & 7beta)? (Wanted to use different Vlans for each of the LTE modems [2]) I'm asking this, because I read on the Routerboard forum that the MT7621A chip & RouterOS have some issues with vlans: https://forum.mikroti...

Acryli

M.2 is only M.2 port.

You mean PCIe bus?

Because M.2 specifications defines PCIe bus and/or USB2/3, I2C,...

Saying M.2 is only M.2, is actually not really clear. But I assume you want to say "PCIe bus only" right?

Acryli

Yes I know that diagram, but it's c*** I don't trust it because: 1. It's clearly stated that M.2 slot has a PCIe bus. But the "miniPCIe slot 2" there is nothing indicating what that line to the SoC is about (we could thinks it's a PCIe also, but not sure. "miniPCIe" is a connecto...

Acryli

Hello I have 2 questions about the RBM33G and especially it's mPCIe/M.2 ports. https://mikrotik.com/product/rbm33g#fndtn-specifications 1. If I understand right, there is an USB 2 bus present on port mPCIe#0 & mPCIe#1 (if jumper accordingly set of course), but is there a PCIe bus connected to bo...

Acryli

Hello Well, I'm back. I can't get the management vlan to work. On RouterOS: 1. LTE as IP passthrough to eth1 with MAC filter 2. Added a Vlan 2 on eth1 for the management. 3. Assigned the IP 192.168.88.100 to the vlan 2 interface On Ubiquiti Edgerouter: 1. WAN on eth4 + firewall rules 2. Added a Vlan...

Acryli

Well, I found the error and totally my fault... I forget to set up the DHCP on the WAN port of the Edegrouter... Now it wrong. Thanks for your help You have ONE ethernet and you not must create a Bridge. Just create two VLAN's at Ether1. *) vlan id 2 as management *) vlan id 3 as lte passthrough Ena...

Acryli

v013

But sill not working :-/

With the command /ip dhcp-client print, I'm getting an empty table:

# INTERFACE USE ADD-DEFAULT-ROUTE STATUS ADDRESS

Acryli

It could be related to a firmware bug according to this tread:
viewtopic.php?t=148697

I'm using version MikroTik _CP_2.160.000_v008

Apparently this bug has been fixed on version v012.

Where can I download it????

Acryli

Thanks

Yes, it's set to no, but it doesn't work

Other people don't seem to have trouble to make Mikrotik's lte modems to work in bridge mode.

Acryli

Thank you for your answer.

It's a standard Mikrotik R11e-LTE modem card.
The default value for the parameter ignore-directip-modem is NO.

Is that ok?
Should I change it to yes?

(Is PPP = DirectIP mode? It's not clear in the manual)

Acryli

Up please :-/

I also set up the passthrough-mac address parameter, but it hasn't changed anything :-/

Acryli

Hello I'm trying to setup my LHG LTE in bridge mode (Ubiquiti Edgerouter acting as router), but I can't get it to work, and I don't know what I'm doing wrong. I'm following the instructions written on this page: https://wiki.mikrotik.com/wiki/Manual:Interface/LTE#Passthrough [admin@MikroTik] > /inte...

Acryli

+1 I'm interested to know too.
(Actually wanted to use a LM940)

Have you tried to unlock the card by entering the Pin code manually over AT Command?

Acryli

Hello

I have a simple question about the LHG mount.
https://mikrotik.com/product/lhg_mount

How many degrees can the mount adapter rotate???

Thank you

EDIT:

Oh ok, it's +/-20°, we can see on the picture.

Acryli

Overlooked that one: LTAP has only Fast Ethernet, no sense to add CAT6 into that... Well I don't agree, for the simple reason because there is a huge difference between the theoretical performances and the real performances,. Let's take the Snapdragon X12, which is a CAT12 DL / CAT 13 UL (600/150Mb...

Acryli

Thank you for the link. The Sierra Wireless MC7430 seems to be the only one in the list to be cat6 (300Mbps), but it needs hardware modifications (isolates pins). And it is also expensive for a cat6 modem, I prefer to wait the support of the EM7565 (600Mbps) that isn't a lot more expensive, but I do...

Acryli

Hello

Is there somewhere a compatibility list of LTE modem (miniPCIe or M.2) that work with RouterOS???

I wanted to know if there were cards available that support speed greater than 150Mbps dl.

Thanks

Acryli

Up

Acryli

Any news about the support of the EM7565 modem on RouterOS?

Acryli

Hello I wanted to ask if there are some picture of the inside (the electronic) of the LHG LTE Kit available? I'm just curious :) Beside that I don't know if the Mikrotik Team read my suggestions for an improved LHG LTE version, I wrote on this topic "Future of LTE products, user feedback reques...

Acryli

We would like to know our customer wishes and use cases on what kind of future LTE technology would be interested in? 1. Which LTE Category you are interested in most - CAT6, CAT7, CAT9, CAT11, CAT12, CAT16 or some other? 2. Which LTE bands and which Carrier Aggregation combinations should be suppo...

Acryli

Thank you for your answer. I have yet another little question. Do you know if Mikrotik plans to release a faster version of the modem in the near term? (150Mb/s LTE modem, sounds a little bit "outdated". I think in 2018 the minimal people could expect is a 300Mbit/s LTE-A modem. At least t...

Acryli

Hello

I wanted to ask you some technical details about the dual SIM feature of the MikroTik LtAP mini LTE kit modem.

Is just 1 SIM card active at a time?
Can one SIM card be used for 4G data and the 2nd SIM used to send/receive SMS over 2G, at the SAME time?

Thanks

Search found 50 matches