MikroTik

cascom

The port also needs to be allowed on the "input" in the /ip firewall filter for the same port/protocol as the dst-nat to work. And it should be added just below the ICMP input accept rule. The dst-nat rule is still needed. Note here....this part is critical: And yes, we have fixed public ...

cascom

All I have is LTE in that list, no WAN.
When opening up the LTE and checking status the fields are all blank

cascom

I have a static IP simcard from T-Mobile running on my SXT.
I can see the publib static IP on the WEBFIG screen when I login but wan to see more.
How can I view the Subnet and Gateway also for this LTE WAN connection?

cascom

You might try deleting an extra IP/dhcp—server/network that quickset must have created: /ip dhcp-server network add address=0.0.0.0/24 gateway=0.0.0.0 Should not be there. You can safely delete it. Not sure that explain port drops. Other than that your config looks like it should have LTE internet ...

cascom

I'd also recommend trying 7.2. It has a lot of LTE fixes over any of the 7.1.x versions. I am on 7.2 both OS and firmware What are you seeing in the logs? If it's a crash, that explain "losing a port". M/R/STP could also explain ports going "dead"...are the LtAP plugged into a l...

cascom

Your LHGG has a default configuration that just works with LTE and creates LAN on ether1. The issue here is NO default configuration is going to do that on the LtAP version you have. So basically you're going to have tackle on the LtAP, one way or another. I have now done this on 3 different brand ...

cascom

ether1 is not your WAN port... lte1 is your WAN port... So remove ether1 from the WAN list and add your lte interface... Also i see no masquerade rule for your LTE interface... ip firewall/nat/add chain=srcnat out-interface-list=WAN action=masquerade No IP address assignment on your Bridge and no D...

cascom

Everyone has been so helpful and the config tips get me going however, defaulting and resetting and netinstalls all get me back to my same problem... Can you please /export hide-sensitive the configuration you have after reset to no defaults was made ? # mar/18/2022 18:25:22 by RouterOS 7.1.3 # sof...

cascom

Here https://help.mikrotik.com/docs/display/ROS/LTE#LTE-Quicksetupexample you can see the APN configuration... Then, in a simple Router setup, create a Bridge and add the ether1 and wlan interfaces as ports, set an IP address to the Bridge interface e.g. 192.168.1.1/24, create a DHCP server on the ...

cascom

ok @sindy, i see your point... My first step always when logging in to a new device is reset to no defaults, so i don't really look what the defaults are or not... Then a reset to no-defaults and step by step configuration with no quickset... I think the OP has an SXT and/or LHGG, and guessing the ...

cascom

Mikrotik help page on "Default Configuration" has a clue on what's going on here. See https://help.mikrotik.com/docs/display/ROS/Default+configurations If the LtAP comes without any Mikrotik LTE modems install, comes to the "WISP Bridge" configuration. While LtAP that come with ...

cascom

Mikrotik help page on "Default Configuration" has a clue on what's going on here. See https://help.mikrotik.com/docs/display/ROS/Default+configurations If the LtAP comes without any Mikrotik LTE modems install, comes to the "WISP Bridge" configuration. While LtAP that come with ...

cascom

I just wanted to see if this is normal LtAP behavior or if mine is goofy right out of the box. That's why I've suggested you to dump the default configuration script and see whether it adds the IP address etc. Since you can add all that manually, the hardware is not broken. Hence the most likely th...

cascom

@sindy, I think this thread is a continuation of https://forum.mikrotik.com/viewtopic.php?t=182960 ... The default configuration is really just those lines on the LtAP, it starts as the "WISP AP" default it seems But I can see the confusion here. Looking at the QuickSet profiles, none sup...

cascom

I have tried netinstall several times. The question is how does the default configuration look like in case of 7.1.3 on LtAP. /system/default-configuration/print file=defconf will place the default configuration script into a file named defconf.txt, which you can download and inspect. Other than th...

cascom

Are there any export of interface that I can do and import them to save time? You cannot save a backup of the configuration and load it on another model. But you can export the configuration into a script and run that script on another device regardless its architecture. In order to make it run suc...

cascom

I am not having any luck with the LtAP setup. It does not come up as 192.168.88.1 after any reset, netinstalls, etc. I have tried 6.8, 6.9, and 7.1 OS netinstalls but only the mac appears in winbox. Is this a problem with the architecture? my mipsbe loads on LHGG units are so easy... this mmips is ...

cascom

[/quote] If you can get in with winbox+MAC address, I'd really recommend V7. If your testing, 7.2rcX line has a lot of LTE fixes vs 7.1.x. Once in, you can try to use QuickSet with the "LTE AP" mode, which should get you a working configuration, hopefully with 192.168.88.1 on ether1 of LtA...

cascom

New LtAP out of box does not provide IP (normally on other MikrTiks I have it gives 192.168.88.1 as it's address) I used Winbox to get in via the MAC address and put 7.1.3 OS on it so it would detect my LTE MODEM (RM502Q) We get internet access on the device only, it will not pass internet to the et...

cascom

[/quote] We've used wAP and LtAP, but IMO if you want two high end modems, using two wAP devices gives you some hardware redundancy+VRRP. While the 8 SMAs needed for 4x4 MIMO with two modems inside makes the LtAP pretty bulky - in same case this may be handy. But the flexibility of the wAP is why we...

cascom

wAP ac R is outdoor, miniPCIe, USB 3.0 and comes without modem as option (RBwAPGR-5HacD2HnD). You drill out the holes on the bottom of the unit to connect an external antenna, there 4 spots. So you need the right pigtail length with right combo of SMA[/QMA] to U.FL[/IPEX4] pigtails, plus some exter...

cascom

wAP ac R is outdoor, miniPCIe, USB 3.0 and comes without modem as option (RBwAPGR-5HacD2HnD).
[/quote]

Nice, just ordered one from Baltic, now I just need some extra antenna ideas so I can make it 4x4 MIMO

cascom

The Ethernet port on the SXT side would be the bottleneck. The newer LtAP might have USB3 - look up the CPU specs to see. Other than that you’ve got the Chateau. There isn’t any newer devices with integrated antennas unfortunately. I saw the SXT has only 10/100 that is why I upgraded to the LHGG wi...

cascom

I want to put my Quectel RM502Q in to a routerboard or other MikroTik device min PCI express slot and get full benefit of speed available from the 5G/LTE network I connect to. When I use the SXT-LTE I only get about 120Mbps tops and with the LHGG I get speed tests as high as 320Mbps. My understandin...

cascom

You can do both: use winbox to connect directly to CAPs ... and use router (CAPsMAN) to push software upgrades, monitor and manage wireless interfaces. Note that you can't manage wireless interface of CAP with direct winbox connection when CAP is managed by CAPsMAN. Another note: make sure that con...

cascom

Multiple caps per port are no issue.

This is great, up and running now, quite painless too.
Will I be able to manage with remotewinbox too? Will I just use the Router to update firmware and monitor etc?

cascom

You can start off by reading (and following) the manual: https://wiki.mikrotik.com/wiki/Manual:S ... sMAN_setup

Is there only 1 cAP ac allowed per ethernet port?
Or can several cAP ac devices connect to a switch that is connected to the ethernet port with CAPS enabled?

cascom

Do you have a link to the best known method or configuration steps for capsman?

cascom

I am using an RB4011GS as my router, internet works great wired and wireless on it. Now I am hooking up at least 9 wireless access points that I want in bridge mode so the the router gives IP address to any and all devices that connect to the Wireless access points. I will ba hardwiring each of my c...

cascom

OK, thanks everybody, a piece of tape it is. I have psalm that comes with an antenna I buy from the company “Bec“. I really honestly just didn’t know if it was a flexing, gap, temperature, etc. problem or if it was moisture/oxidation. I didn’t know if the tape was just a Band-Aid masking the problem...

cascom

I have several hundred of these outdoor units, would like to avoid the tape option. Hoping a gel or spray had been thought of and tested. Why ? that tape trick is already as old as the existence of SIM cards and is still applicable today for some situations. It get's even better, if you make the ta...

cascom

I have several hundred of these outdoor units, would like to avoid the tape option. Hoping a gel or spray had been thought of and tested.

cascom

My SXT LTE units constantly need Simcards to be reseated after severe temperature swings. Like if one day it is hot and sunny and the next day it is cold we have complaints of no service. We go onsite and login and the MikroTik says no sim present. We reseat the sim and service works great for month...

cascom

I am trying to accomplish this same task with my SXT LTE6 as well. The goal is to just use the SXT LTE6 as a MODEM and pass the IP strait to my hardwired laptop. Is there a streamlined step by step config for this or an example? I'm afraid of removing items from bridge and losing communication with ...

cascom

I have put RouterOS 7.1 beta on my MikroTik SXT LTE6 so I can use the Wireguard function. I purchased a client subscription for Wireguard from OVPN https://www.ovpn.com/en and generated keys/config/etc. Below is the config file but unable to enter all fields as some are invalid, I also don't know ho...

cascom

I have a Wireguard subsciption vis OVPN.net and trying to use their config file to enter my info into my SXT LTE6 running 7.1
I'm using Winbox, have not mastered CLI yet.
I can see wireguard in my interfaces list.
Do I now need to add it to the interface list?
Sorry, I'm real new.

cascom

Using an SXT LTE-US

Bob.

cascom

Where do you enter the static public IP in the Mikrotik?
I have recently upgraded my plan to a static public IP, I have the APN and the IP but don't know where to enter the IP.

Bob.

cascom

I am using and AT&T simcard getting excellent 4G/LTE speeds and needed a Static/Public IP. I have ordered it from my wholesaler/vendor who I get my service activation from and they told me the IP address and APN to enter... I have entered the APN but I do not know where to put the the Static/Pub...

cascom

Brand new RB951ui-2hd, upgraded firmware to 6.43.4 Connected via wifi Internet in Ether1 and it works. I added a PPP Interface L2TP Client, I named it RSI and Entered my login info in the Dial Put tab... do I need profile info? Do I need to add to a bridge so I can access VPN addresses? My Status sa...

Search found 40 matches