Search found 7 matches
- Sat Mar 21, 2020 4:54 pm
- Forum: General
- Topic: NUC connects with hAP lite via Swith only. w/o switch: no link. MDIX-problem?
- Replies: 0
- Views: 1593
NUC connects with hAP lite via Swith only. w/o switch: no link. MDIX-problem?
I have a hAP lite in bridge mode connected with two PCs and an upsteam router. An Intel NUC NUC8i5BEH works only if connected via Switch. If I connect NUC directly to hAP the cable test shows "no link". Looks like auto sensing / MDIX problem. As soon as I connect a switch in between it wor...
- Sun Dec 22, 2019 5:38 pm
- Forum: General
- Topic: permanently end DNS traffic from mikrotik to IDS (tool sniffer vs calea) [SOLVED]
- Replies: 2
- Views: 1809
Re: permanently end DNS traffic from mikrotik to IDS (tool sniffer vs calea) [SOLVED]
Thanks Sob, this solves the issue!
- Sat Dec 21, 2019 2:32 am
- Forum: General
- Topic: permanently end DNS traffic from mikrotik to IDS (tool sniffer vs calea) [SOLVED]
- Replies: 2
- Views: 1809
permanently end DNS traffic from mikrotik to IDS (tool sniffer vs calea) [SOLVED]
Hello, I'm trying to send any DNS traffic from mikrotik which operates in bridge mode to a remote server. I discovered three ways to accomplish this - a calea options, a firewall mangle sniff TZSP action and /tool sniffer. I set up a linux server with a tcpdump capturing port 37008 in a ring buffer....
- Wed Feb 06, 2019 12:33 am
- Forum: Beginner Basics
- Topic: heX with VLANs and trunk to a Router on a Stick (a transparent proxy) with PBR [SOLVED]
- Replies: 2
- Views: 1039
Re: heX with VLANs and trunk to a Router on a Stick (a transparent proxy) with PBR [SOLVED]
Thank you, it worked!It can be done.
- Sat Feb 02, 2019 3:49 am
- Forum: Beginner Basics
- Topic: heX with VLANs and trunk to a Router on a Stick (a transparent proxy) with PBR [SOLVED]
- Replies: 2
- Views: 1039
heX with VLANs and trunk to a Router on a Stick (a transparent proxy) with PBR [SOLVED]
I'm trying to setup a rather unusual configuration on my heX (RB750Gr3): [internet] - [DSL Router] [heX :1] [heX :2] - untagged - [PC] [heX :3] - [hex :4] - vlan 10 - [trunk] - [eth0.10 transparent Proxy] [hex :5] - vlan 20 - [trunk] - [eth0.20 transparent Proxy] on a heX I need a PBR rule which red...
- Sat Feb 02, 2019 12:38 am
- Forum: General
- Topic: cannot access HEXv3 (RB750Gr3) after successful Netinstall [SOLVED]
- Replies: 2
- Views: 1544
Re: cannot access HEXv3 (RB750Gr3) after successful Netinstall [SOLVED]
OK, solved: choosing the "apply default config" checkbox in the netinstall UI restored the configuration!
- Sat Jan 12, 2019 10:39 pm
- Forum: General
- Topic: cannot access HEXv3 (RB750Gr3) after successful Netinstall [SOLVED]
- Replies: 2
- Views: 1544
cannot access HEXv3 (RB750Gr3) after successful Netinstall [SOLVED]
Hello board, I need your help. After I've upgraded my HEX from WebUI it cannot be accessed anymore. No problem - using a NetInstall (and following the NetInstall manual _exactly_) I've successfully reimaged the board (the Netinstall UI showed OK). It starts, but cannot be accessed anyway, no IP addr...