MikroTik

leaf

http://wiki.mikrotik.com/wiki/Supported_Hardware

leaf

Thanks Normis, shall do. The Rb is due in the country in a week or so.

leaf

Are there any plans for support for the ZTE MF626 HSDPA USB Modem. The device is badged by Telstra in Australia and is in common usage as a general purpose USB modem. Reading between the lines it appears similar to the other existing MF62x devices. This would be a readily available and good low cost...

leaf

Thanks for that Normis,

The price point of the RB433UAH & a low cost USB 3G unit will be devastatingly effective!!!

Cheers

Don

leaf

Is it possible to use a mini-pci USB card on Rb hardware to gain access to 3G modems?

leaf

USB is a bit like mini-pci-e. Missing to date. Looking forward to seeing a low cost unit with one or the other fitted.

leaf

Good point Normis. This 3G router area appears to be quite a potentially large emerging market segment...

leaf

Any vague estimates on release dates?

leaf

After speaking to a few 3G card disti's the consensus is that mini-pci is dead in new designs and they are moving to support mini-pci-e instead.

leaf

Are there any plans at present to release a low-mid end RB with mini-pci-e. We are looking for something to carry a common 3G module. eg Sierra Wireless MC8780

leaf

1: Yes
2: Upgrading firmware on remote embedded devices
3: Some form of mac authentication
3: Read & Write access (maybe definable by MAC)

leaf

I would also like to throw in support for a basic TFTP server... We operate a couple of Terayon CMTS's and have to have a seperate DHCP server / TFTP server to support the cable modem file distribution. I would LOVE the idea of using my existing Mikrotik router to be able to handle these requests. ...

leaf

It was more a case of trying to specifically find a way of using the RB333. I couldn't see an obvious way of doing it but again looked to see if one of the guru's knew of a non-obvious misappropriation of other functionality which may have achieved the required functionality. A bit of a baling twine...

leaf

Tried asking this earlier with no joy. Thought I might find some new faces and ideas... Scenario: Embedded devices pumping out unidirectional syslog packets via UDP to server. Devices lack time and bandwidth to send duplicate packets to multiple targets. Client's windows server hosting syslog daemon...

leaf

The syslog packets are from embedded boxes. They generate a lot of Syslog data and so I am not able to duplicate the packets at the source as it will occupy too much CPU time. At worst case I was looking at a script on the ROSbox which looks for a dead server & then redirects accordingly. It wou...

leaf

Is it appropriate, <<or possible>>, to Tee unidirectional Syslog UDP packets to two recipient servers by sending the packets to an RB133 as the primary address & then forwarding the packets to two destinations?

leaf

Hi All, Are there any ( as in any anywhere on PCB ) hardware lines available on PCB which can be controlled from ROS e.g. discrete bit I/O, SPI, I2C etc . I am looking at using the RB133 to reboot some attached equipment on the network when it goes wheels up ( Windows... gotta a love it...). Failing...

leaf

Having said this I wouldn't like the original request to get lost in the noise. User supported modules or not I would still like to see TFTP functionality available one way or another.

Don

leaf

TFTP should be able to work outside the layer2 lan. We have a central TFTP server we use to provide firmware files to switches and configuration to and from ciscos on various parts of our routed network. The particular client implementation on the majority of devices doesn't route. If your applicat...

leaf

The need is strictly TFTP as there are many other boxes from other Industrial suppliers that we have no firmware access to. The lowest common denominator & standard protocol for these widgets for firmware updates is TFTP. On our widgets the whole boot loader & comms system has to fit into 4K...

leaf

Hi All, Is anyone else interested in this facility at all? We have a lot of tiny embedded widgets scattered around on network segments behind RB133's in a set of factories. At present we have tux boxes sitting on the segments to provide a distribution point for embedded firmware revisions for the wi...

leaf

Count me in for 2 bods
Cheers
Don

leaf

I have been running a pair of RB133C's in the lab for a week now with PPP over the async port and a PC at each end running btest via the ethernet ports. They appear quite stable. I had the problems which you described & so stripped the OS down to bare bones & things are OK. Just the minimum ...

leaf

I should add to this that the PPP link has it's own 10.10.10.xx address pair allocated to the async port

leaf

Dude 2.2 Hover mouse over PC icon & dialog pops up. Most are contained within the area of the screen even though they are near the edge. Latest one has the box partially off screen. This PC has extended desktop off to a TV. It would be good if the Dude kept it's pop-ups within it's own window as...

leaf

I just ran Dude 2.2 on a network with a single address space xx.xx.xx.0...255. Within this space there are two segments joined by PPP courtesy of two RB133C's running ROS3b9. The resultant map shows all nodes connected to the xx.xx.xx.0 address space but ignores the presence of the PPP link. As ther...

leaf

>> use only winbox to connect to 133C as this uses a lot less memory as console. Tried a system system/reset-configuration via telnet & then started again. Usually shows 4.6...5MB out of 16MB memory free. The unit initially connected via Winbox and then disconnected. Connection via telnet is rel...

leaf

Investigated this a bit more... Only the PPP client end displays the winbox slowdown / fail problem. Try opening a terminal window & it may show the signon after a while & usually Winbox will disconnect shortly after. Rebooting often helps but not consistently. I noticed earlier that the act...

leaf

The lockup Problem appears to occurring only on the PPP client end of the link. The PPP link is still functioning well but the user interface via winbox is locked out. Tried restarting winbox a few times and got the earlier config of dialog boxes but no data. Eventually ( 2 minutes ) the boxes updat...

leaf

One of the units locked up when running packet sniff. After reboot it allowed access via winbox & I noticed that it had erased all the routes table & refused terminal access. Tried cold boot and configuration reset via the boot menu. Now I have terminal access again in winbox and some ( not ...

leaf

I tried just loading the system & PPP packages. This time the Rb133C appeared stable in this configuration. I then upgraded a second unit and ran Bandwidth test over the async PPP link between the two RB133C's. Nice solid 44kbps TCP running bidirectional with a 512 byte MTU. This cured the probl...

leaf

I just tried an upgrade to a RB133C with what appeared initially to be a bricked outcome... The netinstall went OK with the full package. Unit rebooted but no console login or winbox connectivity I did a config reset from the bootloader, exited & waited followed by a cold boot Got a console afte...

leaf

This seemed like a trivial question and yet it is never answered...

Any clues?

It would appear that the baud rate setting is locked at 115K by RouterOS, strange given that the start-up rate at boot is able to be changed.

Is the assumption correct? if so is there a reason for this?

Don

leaf

I should add that I have disabled the services using the port before trying to change it. I note that the console port can only be disabled & not removed.

Don

leaf

Tried everything I can think of to change the baud rate on the RB133 serial port for in RouterOS but it refuses to allow the change. I have PPP running but only just as when the traffic increases the system struggles. I implemented queues with speed limiting but I am still seeing CRC errors. 115K is...

leaf

Mikrotic tech Support got back to me pronto with the following: Yes you can use serial port for ppp connections. Disable console: /system console disable 0 ; now you can set up ppp client or server over com port. /interface ppp-client add null-modem=yes port=serial0 disabled=no ; the same for server

leaf

Thanks for the assistance.

We now have 4 on the way, due tomorrow.

Cheers

Don

leaf

Apologies for this turning up in a few places. Trying to get a reply asap so that we can get a purchase order in on equipment. I am looking for a solution to allow me to run IP over a number of sets of existing 115KB RF links which have RS232 async ports. I am keen to purchase the RB133 units howeve...

leaf

I am looking for a solution to allow me to run IP over a number of sets of existing 115KB RF links which have RS232 async ports. I am keen to purchase the RB133 units however have suspicions as to whether the console port will reliably support PPP. Can anyone confirm whether the port is usable for P...

Search found 39 matches

Re: USB via mini-pci

Re: Planned support for ZTE MF626 HSDPA USB Modem

Planned support for ZTE MF626 HSDPA USB Modem

Re: USB via mini-pci

USB via mini-pci

Re: 3G Mini-PCI (Not PCI-Express)

Re: 3G Mini-PCI (Not PCI-Express)

Re: mini-pci-e on RB

Re: 3G Mini-PCI (Not PCI-Express)

mini-pci-e on RB

Re: TFTP

Re: Feature Request : TFTP server

Re: Tee single incoming UDP data stream to multiple IP targets

Tee single incoming UDP data stream to multiple IP targets

Re: UDP Data Tee using Port forwarding

UDP Data Tee using Port forwarding

RB133 Hardware I/O lines available under ROS

Re: Feature Request : TFTP server

Re: Feature Request : TFTP server

Re: Feature Request : TFTP server

Feature Request : TFTP server

Re: Mum Australia (I wish) :-)

Re: 3.0beta and RB133c

Re: Map of Network - PPP confusion during discovery

pop-up dialog off screen

Map of Network - PPP confusion during discovery

Re: 133c Beta 9 - Renders system useless

Re: 133c Beta 9 - Renders system useless

Re: 133c Beta 9 - Renders system useless

Re: 133c Beta 9 - Renders system useless

Re: 133c Beta 9 - Renders system useless

Re: 133c Beta 9 - Renders system useless

Re: RB133 Serial Port Baud rate - history repeats?

Re: RB133 Serial Port Baud rate

RB133 Serial Port Baud rate

Re: PPP via serial port on RB133? Urgent

Re: PPP via serial port on RB133? Urgent

PPP via serial port on RB133? Urgent

PPP via serial port on RB133? Urgent