MikroTik

mbethers

I'm using an Audience with a Startlink router. When I put the Startlink in bypass mode connected to the Audience, traffic drops to the internet every minute or so for 5 to 10 consecutive pings and then resumes. When I default the Starlink back to router mode the problem resolves. I'm able to duplica...

mbethers

I just experienced the first power-up of an Audience and it was stuck in a boot loop. I managed to NetInstall it to version 7.15.3, logged in, and then updated the firmware. However, every time I proceeded to configuration, it started boot looping again. I repeated the NetInstall process, logged in,...

mbethers

ANAV - Rock Star!! That worked perfectly. Sob - I originally had everything one interface and was having the same issue. I put them on different interfaces in attempt to follow some of the posts describing the mangle rules. What ANAV suggested works great, but if I could save a couple interface port...

mbethers

I'm looking for just a nod in the right direction to solve a problem that I haven't been able to figure out thus far. I have MT device setup with 3 WAN interfaces. However, they come from a single modem with a 5 static IP block. Currently, for example, I'm using 1.1.1.7/29, 1.1.1.8/29, and 1.1.1.9/2...

mbethers

There a quite a few posts on this topic, but I have not been able to flush out a solution. I have a working IPSEC Tunnel. I can successfully communicate between LAN1 and LAN2. What I'm attempting to accomplish is to route traffic from LAN 1 over the tunnel and out WAN 2. One suggestion that made sen...

mbethers

I have a situation that I've been unable to come up with a working solution. Any help would be appreciated. I have to static IP addresses from my provider, with the same gateway, IE: IP1 - 1.1.1.4 IP2 - 1.1.1.5 Gateway 1.1.1.1 I have two separate LANS 10.10.10.0/24 10.10.11.0/24 On each LAN I have a...

mbethers

I trying to use the bridge filter to look for traffic from a specific IP address. If I Torch the bridge interface I see all the traffic including what I'm looking for, and it shows the Eth. Protocol 800(ip). If I enable the Bridge Filter and want to filter by IP, it requires changing the Mac-Protoco...

mbethers

Resurrecting old post with no reply. I'm having the same issue. ROS 6.38.3 on 750GL. I have an firewall filter set up and logging. I need the src-mac to log, but it is not showing up. I'm getting for example: 06:38:51 firewall,info trap forward: in:bridge1(ether1) out:bridge1(ether4), proto UDP, 192...

mbethers

I'm try to locate where some specific traffic is coming from on a non Mikrotik network. The NetAdmin setup a mirrored port for me. I followed the suggestion on another post and configured a 750GL as follows: 1. Connect port 1 to the mirroredport 2. Use port 2 for administration purposes 3. Set maste...

mbethers

I have a very perplexing problem with an MAP2N. I was unable to reach the device from the WAN ip address. I could ping it and determine it was online, but no access winbox, telnet, etc. I connected WiFi and the device was indeed online and I had access to the internet. I checked services and made su...

mbethers

I'm trying to execute this simple script: /ip add set [/ip add find comment=static] disabled=yes]; /ip r set [/ip r find comment=static] disabled=yes]; /ip dhcp-cl set [/ip dhcp-cl find interface=wan] disabled=no; It works fine when pasted into a terminal, but when executed from the script it only r...

mbethers

Is there a way to strip the IP address from the response leaving the netmask. I found lots of posts doing the opposite, but in the script I working with I need the netmask only. IE. :put [/ip add get [find interface=ether1] address] = 10.10.10.1/24 :put [:pick [/ip add get [find interface=ether1] ad...

mbethers

Thank you.

mbethers

Is there anyway to use a variable after a / character. I'm trying to do something like this"

ip add set [find comment=static] address=staticip/$staticsub

That obviously doesn't work. Any help would be appreciated.
Thanks,.

mbethers

Can someone help me out with the meaning of an inbound connection where the TCP State is stuck and Syn Received? Yesterday, without any changes on my end. One particular outside IP address can no longer get to a server on my LAN. That particular IP can't ping my outside connection or telnet, etc. No...

mbethers

Anyone else have any luck with their ChangeIP scripts since the website changeover?

mbethers

I'm trying to connect a device to our network that I'm having problems with. The vendor sent back: "It looks like your firewall needs to allow Trigger Ports 8000-20000 open. Those are the data ports that allow the actual audio data through, different from Port Forwarding." I have done some...

mbethers

I would appreciate a shove in the right direction. I need to setup a vpn from a device to a Mikrotik I my side. The device on other side is only capable of IPSec, GRE, or SSL tunnels. The device on their side is nat'd. Is there one of these options that I would be able to get working when they don't...

mbethers

Did you get this to work?

mbethers

V5.25

When I run it with your Command line it does work. It thought I was going crazy.. But it does not working when you click the Run Script button.

mbethers

I'm trying to execute simple script, an example of which would be:

:global test [/ip dhcp-cl get [find interface=ether2] comment];
:log info $test

I can get the individual lines to work in a command console. But they don't work when run from the script.
What am I missing?
Thanks,

mbethers

I'm trying to configure a RB493 with two WAN interfaces on ether4 and ether7. I want to configure it so that traffic from the outside leaves on the interface that it came in on. I thought I had this figured out once before, but it is not working now. Here is what I'm using. Any help would be appreci...

mbethers

We have been using the Sierra Wireless GX440 modem on Verizon 4G service with a Mikrotik with great results. Yesterday however we upgraded the GX440 modem which broke our solution. I hoping a networking guru can shed some light. The modem is setup as a modem, no routing functions, or security enable...

mbethers

I know that I can find an interface based on its flag (dynamic, invalid or disabled). ie. :put [/ip add get [find invalid] interface] What I want to do is query and interface and find our whether the interface is flagged dynamic, invalid or disabled] something like? :put [/ip add get [find interface...

mbethers

This is an old thread, but exactly what I'm trying to accomplish. Anyone have any input?
Thanks,

mbethers

Is there any way of sending an AT command from a script. For example I want to script these steps:
/system serial-terminal usb channel=1
ATZ
<Ctrl-A>
q

Thanks.

mbethers

Sorry to budge in. Sam - How does one get ahold of you these days?

mbethers

That works. Thanks guys.

mbethers

I'm tyring to figure out how to break a loop when a condition is met. I have the following script working the way I'd like: :global source [:tostr [/system resource usb get [/system resource usb find ports=0]]] :local start ([:find $source "device-id="] + [:len "device-id="]); :l...

mbethers

Ok. If you can be persuaded contact me at sierra297[at]comcast.net.
From reading your posts it looks like you can do in a minute what I'm going to beat my head against the wall for the weekend trying to figure out.

Thanks again for getting me started.

mbethers

Nice! Fewi are you on the consultant list?

mbethers

I would like to extract a value from a response. For example: :put [/system resource usb get [/system resource usb find ports=0]] response: .id=*3;device=2:3;vendor=CMOTECH CO., LTD.;name=CMOTECH CDMA Technologies;vendor-id=0x16d8;device-id=0x6002;speed=12 Mbps;ports=0;usb-version =1.10 I would like...

mbethers

Craig- I've serached your posts regarding the U301 and it looks like it should work. But I'm having trouble. I'm using 4.10. When I plug it in I see two serial ports, one has 4 data channel, the other 1. There is nothing special in my ppp-cl config: /interface ppp-client add add-default-route=yes al...

mbethers

Interesting. It is not the time, as if the time is wrong I get an that error. I'm just getting invalid or unknown key on the board side and BADSIG on the server side.

Thanks,
Mike

mbethers

I'm trying to set up my own BIND server and use the dns-update tool. I'm getting a BADSIG error that is mentioned in these threads. None of these threads mention a resolution. Is the dns-update tool custom to changeip.com? http://forum.mikrotik.com/viewtopic.php?f=2&t=30632&hilit=badsig http...

mbethers

I'm trying to develop a script to manage IPSec tunnels, but it does not appear that the IPsec Policty nor the IPsec Peer settings allow for a comment, so I can't figure out a way to disguish the line I'm tyring to change. IE. /ip ipsec policy set [/ip ipsec policy find comment=x] x=y] Is there a way...

mbethers

Both are dynamic IP addresses, so I don't think I can create the default route. Correct or no?
Thanks,

mbethers

I am setting up a router with a PPPOE dsl line and 3G USB connection. I would like the DSL line to be primary and failover to the USB 3G if the DSL goes down. I have them both working, but I can't find a way to set the distance. They both come up with a route distance of 1 so it is a crap shoot as t...

mbethers

Is there any way either by mac or otherwise to determine if a radio card installed in a board is and xr2 or sr2 remotely?
Thanks,

mbethers

Is it possible to pulse one of the pins on the serial port of a 433 board. I found at least one post on the subject which mentioned to try: / port set serial0 dtr=on rts=off I've tried that as well as switching dtr=on to dtr=off with a script, but it is not clear as to whether the RB433 supports dtr...

mbethers

Is there a way to use the get command for flags? I want to create a script based on whether a usb port is flagged inactive. I can get the status of every other parameter, ie: :put [/port get [/port find name="usb2"] used-by] Is there a parameter for status? Or another way to do this? Thank...

mbethers

I'd like to load a script with netinstall that includes adding a system password. I haven't been able to get this to work. If the current password is test and I want to change to test2, I can cut and paste into a telnet window: password test test2 test2 ..and it works. But if I try the same thing wi...

mbethers

Is it possible to put a switch on an RB411 and run the WAN and LAN side of the router on one physical interface? I'm still trying to find a solution for replacing the lost 133 board. I need that physical size but more than one ethernet port.
Thanks.

mbethers

Is there a command I can use to return just the IP address assigned to a specific interface?
A search resulted in something close to following line, but it doesnty work.

:put [/ip address get ether3]

Thanks,
Mike

mbethers

Still looking for an API consultant to develop an configuration application. It will be worth someones time. Please contact me.
mbethers[at]comcast_net
Thanks,
Mike

mbethers

http://www.orbitmicro.com/global/3264bi ... 9_186.html

mbethers

mbethers

Did an API consutant list ever get compiled. I'm intrested in having a mini winbox applicatin written.
Thanks,
Mike
mbethers_at_comcast.net

mbethers

This script won't work in 3.11, can anyone suggest a fix? :global if-snr [ /interface wireless registration-table get [/interface wireless registration-table find] signal-to-noise ] :if (($if-snr > 0) && ($if-snr <= 15 )) do={/blink duration=250ms} :if (($if-snr > 15) && ($if-snr <= ...

mbethers

Any updates. I'm in for any nre costs that may be needed to move this along if it will help.

mbethers

After a few days of testing, we have found that the SR2 card disappearing from the interface list all together is happening infrequently. What is happening consitetly is the card is up for a few minutes and then goes dark. You can't see it in AP mode, if you scan with it, it sees nothing. Reboot, do...

mbethers

We have been using the same combination of RB133/xr2 cards for a long time with good success. Recently we had to move to the 433/sr2 combination because of the rb change and xr2 supply problems. Now, we are having problems with the wlan inteface disappearing. Reboot sometimes it comes back, sometime...

mbethers

On every version prior to 3.10 a script including the following command works:
/ip firewall nat set [/ip firewall nat find dst-port=8000] disabled=yes

The command does not return any errors, but it does not execute properly either.

Thanks,
Mike

mbethers

Just a follow-up for those that run into the same problem. I hadn't noticed but both boards had shipped with the soft reset jumper shorted, which was causing the problem.

mbethers

Thanks for the suggestion. But, no luck. I switched the power supply out and the two boards still have the same problem. I tested several other 133 boards on the same power supply and they work fine. Anything else I can try?
Thanks,
Mike

mbethers

I have two brand new 133 boards, having the same problem on each. -Upon trying to connect to the boards the immediately show router disconnected when trying to connect via winbox. -Upon trying to telnet to them, they hand after putting in the correct default admin password -If I try and put and inco...

mbethers

I have a Raven EVDO modem with a static IP from Sprint. When I connect the modem directly to my computer I leave my machine set to dhcp and the modem passes the static ip address to my computer. When I connect the modem to my Mikrotik router and enable dhcp-client, the modem passes the ip address an...

mbethers

I think I found the answer, 29 lines.
http://forum.mikrotik.com/viewtopic.php ... t=29+lines

Has anyone found a fix or way around this. I need the same install on 100+ boards and would like to save the extra step of importing a script on each one.

Thanks,
Mike

mbethers

Does anyone know the size limit for the Configure Script option using Netinstall?
Thanks,
Mike

mbethers

I see a few posts related to this issue, but no resolution/suggestions I can find. I have a wireless WDS link where I'm seeing the following in the log: jan/14 05:50:32 wireless,info MAC@wlan1: disconnected, no beacons jan/14 05:50:33 wireless,info wlan1: data from unknown device MAC, sent deauth ja...

mbethers

Perfect...Thanks.

mbethers

Is there a way to remove a line based on its comment. I'm trying to write a script that would delete an ip address based on its' comment.
Thanks,
Mike

mbethers

In the meantime I have used the following mouser part numbers: 596-2000c LED lens mount 593-cnxbx4108 Solderless LED Connectors 78-tllg4401 Standard LEDS' http://www.vcclite.com/spec_pages/pdf/cat_page19.pdf I then solder the leads directly to the board and able to "remote" the LED. On a s...

mbethers

I'm using a RB133 with v2.9.46. I have lan set up on ether 1 with a DHCP server on Ether1. I have WAN's set up on ether3 with DHCP client enabled. The problem is that if ether3 does not get an IP address quick enough from the ISP, it grabs one from ethe DHCP server of ether1. The DHCP server is set ...

mbethers

I am looking for a consultant/programmer interested in programming a custom interface for the RouterOS. In short, a stripped down version of Winbox.
Thanks,
Mike
mbethers@ipsurvconcepts.com

Search found 65 matches