MikroTik

jrecabeitia

I have changed the partition and installed version 6.47.10 so far so good.
I don't know which baton he sent me, but now I don't see the original partition. Only the current one remains. And I would like to refloat that partition to have a backup in the event of a failure.

jrecabeitia

What do you think if I activate the other partition that contains very old firmware. (6.45.1) If it was a firmware problem or an attack (malicious software entered) the problem should disappear. If it's a hardware problem, continue.

jrecabeitia

Dear rextended, if it were a firmware problem ... because the same thing happens with a router that has another older version. If it were a flash memory problem, because the admin user appears out of nowhere. A mystery.

jrecabeitia

After half an hour, it allowed the access with the user admin without password in the TILE

jrecabeitia

Yesterday I detected that I did not have access to my central router (tile) At the end I accessed with the admin user without password, which was not registered in the router. I tried to backup again and it was impossible. Create the admin user again. I gave it a password. Delete admin. When I wante...

jrecabeitia

I just installed a PowerBox with version 6.40.3 and I notice that it stops responding by IP and does not show mac. There is no way to gain access to i

jrecabeitia

It is not a solution.
The equipment is new and should work.
It goes in tower and its function is to do routing / POE.
I have used the EdgePoint in another installation successfully, but I do not like its software. It is very limited in routing and pppoe

jrecabeitia

I just installed a PowerBox with version 6.40.3 and I notice that it stops responding by IP and does not show mac. There is no way to gain access to it.
Similar problem presented in this thread.
Solution?

jrecabeitia

There are 3 different releases: bugfix, stable and release candidate. Is that so difficult to understand? That is precisely what I say. 6.38.7 (Bugfix only) 6.39.2 (Current) "STABLE" 6.40rc24 (Release candidate) The bugfix Should be on the stable (assumption without errors) Umm no, bugfix...

jrecabeitia

There are 3 different releases: bugfix, stable and release candidate. Is that so difficult to understand? That is precisely what I say. 6.38.7 (Bugfix only) 6.39.2 (Current) "STABLE" 6.40rc24 (Release candidate) The bugfix Should be on the stable (assumption without errors) Umm no, bugfix...

jrecabeitia

In any case, the name should be changed.
Stable with errors
Stable with more errors
Beta future version

Of course, none really stable.

jrecabeitia

I understand that version 6.39.2 is the stable version, since it is the latest version available on the mikrotik website to download. This is version 6.40rc24, which is the one that can have errors, since it is a Beta. There is no sense in mikrotik web version 6.38.7 if it is only about patches. (W...

jrecabeitia

There are 3 different releases: bugfix, stable and release candidate. Is that so difficult to understand? That is precisely what I say. 6.38.7 (Bugfix only) 6.39.2 (Current) "STABLE" 6.40rc24 (Release candidate) The bugfix Should be on the stable (assumption without errors)

jrecabeitia

I understand that version 6.39.2 is the stable version, since it is the latest version available on the mikrotik website to download. This is version 6.40rc24, which is the one that can have errors, since it is a Beta. There is no sense in mikrotik web version 6.38.7 if it is only about patches. (Wh...

jrecabeitia

Or I'm very silly and I do not understand anything.
We are with version 6.39.2 and get bugfix of 6.38.7
How does it apply to 6.39.2?

jrecabeitia

Actually comparing different RB with version 6.39.2 vs 6.38.1 I see that the problem is not the client, but the server that has stopped responding /system ntp server> print enabled: yes broadcast: yes multicast: yes manycast: yes broadcast-addresses: Queries made by ntp of v.6.38.1 are not returned,...

jrecabeitia

When updating to version 6.39.2 both ntp client has stopped working.
My cliente Ntp config

/system ntp client> print
enabled: yes
mode: unicast
primary-ntp: 195.66.241.2
secondary-ntp: 129.250.35.250
dynamic-servers:
status: started

jrecabeitia

Thanks for your answer. The point is that I use Rb493 in the repeaters where I make the PPPOE and routing connections. I do not like the Powerbox, because it has low memory, processing capacity and Ethernet interfaces of 100 Mbit. I need to replace the rb493 and it seems a better hardware Edge Point...

jrecabeitia

Anyone know if the Ubiquiti Edge Point can be placed the Mikrotik system

jrecabeitia

VLANS

jrecabeitia

jrecabeitia

I have four armed vlan and trunk for traveling 4 vlan.
The problem is that 3 of them are ADSL and when you connect one another no.
As weird thing is it does not show the VLAN ID when the hosts are deployed.
Any idea who might be going.

jrecabeitia

RESOLVED

jrecabeitia

My access point now, I have a CCR Administrator, where I do NAT, load balancing, QOS, etc. In this I have connected 3 CCR ADSL and leased line. My internal network is composed of 18 nodes with links, routers and redundant rings. All routing do work with OSPF. Everything works perfectly. Now I incorp...

jrecabeitia

I have a routed network ospf. My Internet connection is in a CCR router with ospf and entered the network after a bridge is a RB1100 router ospf. Currently I do not have any problems. But when I put the internes en SequreISP and is connected to the CCR, the no ospf AS Border Router publishes more wi...

jrecabeitia

Dear rextended, I imagine you think you are a genius and the rest of the forum members idiots. I've worked with Mikrotik products since 2006. I have done hundreds of updates in routerboard since that time, without any problem to call panic. This is a very rare case. I have no explanation because it ...

jrecabeitia

A week that throw the note our disclaimer about what was happening ago. If now some people despite the warning, change to firmware 6.17 - 3.18, which does not take over informarce before doing so. At least everyone knows that something's up. Do not know what causes it, but nobody should update a pro...

jrecabeitia

This security under the name

jrecabeitia

Normis have been able to determine the cause of this problem with firmware 6.17 and 3.18 see? I'm not complaining, many years working with Mikrotik ago and this is the first time that I have problems with one version. Unfortunately, I might forward to update and do not wait long enough, took the pro...

jrecabeitia

/system/packages
mark ipsec
disable
reboot

jrecabeitia

Normis,
Removing the IPsec packet only solves a problem that occurs when you turn back.
It does not solve the problem that gives rise to this issue, which remains a big question.

jrecabeitia

Normis, returning back at 100% of my devices, the IPsec packet takes all the processor.
What I could see is that to turn back the default setting disappears.
I believe that's the cause, but I can not verify.
What I can say is working out down the IPsec packet

jrecabeitia

If the micro processor is 100% remove the ipsec package.
Reincie and should function normally.

jrecabeitia

No link 60Km.
My network has a length of 60 km from end to end, on geographic area.
The longest link I have is 32Km and most are in the 12Km.

jrecabeitia

Normis, I'll go by. Upgrade Device: We went from 6.15 to 6.17 Most teams tear well, only in 3 I am forced to have to do a netinstall. Estimate that could be a current problem. (then discard it, because one of those teams is with UPS and surge) In yesterday morning I see the fall of another link. The...

jrecabeitia

On Saturday, update all my installation with the version 6.17 and then update the firmware of computers. The result was in two adjoining cases. They were inaccessible. Others were falling in these 3 days. Observed loss of configuration in some cases. In others, loss of system packages. I went back t...

jrecabeitia

Dear, I have detected a few days ago my CCR connections. These connections generate significant outbound traffic. They have origin in the CCR The CCR has software version 6.2 and 3.09 firmware Blocking the IP and no other IP while doing the same. It is tedious to have to do this manually. Letting go...

jrecabeitia

solved in version 6.2

jrecabeitia

CCR1016-12G with 3.04 firmware v.6.1 works
When updating the firmware to 3.09 does not work.
backup partition booted.

jrecabeitia

CCR1016-12G with 3.04 firmware v.6.1 works When updating the firmware to 3.09 does not work. backup partition booted. All Partition work on same firmware. but on the other partition I have v6.rc11 and allowed me to download the firmware and boot from the root partition. Now install v6.2 and firmware...

jrecabeitia

With the RB493 is the same.
With the RB133 Connection is lost.
With the RB493G everything right, accessed by ethernet.
No problem with RB711-5HnD
In all cases of V5.25 migrated to V6.0

jrecabeitia

RB433 - ospf router mode - V6.0
At 1.48 minutes to lift the wlan link, stop working and webfig winbox services.
It is only accessible by telnet mac.
It responds to ping. Pppoe connections and normal traffic

jrecabeitia

I have a CCR1016-12G V6.0 - 100Mbits ethernet connects to a RB711-5HnD Nstreme V5.25 - 5GHz links - other end RB711-5HnD V5.25 - 100Mbits ethernet connection to a switch and from there to a PC. Testing with BTest from the PC and the ethernet connection occurs between the CCR and the RB711 fall, when...

jrecabeitia

I have understood that you can not use the version 5 in the CCR.
Can you confirm this?

jrecabeitia

Are two major problems. 1) pppoe - so erratic pppoe disconnects all connections simultaneously. (symptom) 2) Interfaces queue - queue type - if you change default ethernet (no single queue of pppoe nor any other to the eye. They should be) to only hardware queue, appear single queue, but not traffic...

jrecabeitia

Set B and Bridge
Set C as Station Bridge
Set B bridge interface IP address 10.1.35.201
Set C bridge interface IP address 10.1.35.202
No LAN IP
No WLAN IP

jrecabeitia

In the filtering rules:
By setting time interval to activate a rule fails.
For example:
Time: 00:00:00 to 7:30:00
Error undetermined.
Registration is marked in red.

jrecabeitia

at issue was l7
Disable all filtering without positive result.

jrecabeitia

RB1100 - Moving from version 5.20 to version 6.0rc1 triggers the microprocessor 100%

jrecabeitia

I have a link with RB 5HnD SEXTANT is 12.45 Km to signal an both ends of 75dBm and a theoretical speed of 23Mbits. Nstreme use.
I think this is the limit of stable operation.

jrecabeitia

Crea una regla en el firewall para esos rangos de ip

jrecabeitia

Hello, I consult if anyone knows any software for client management, billing, notices of court advance notice. Work with Mikrotik. It would be a very important tool for an ISP. I apologize in advance because it may not be in this forum to discuss this. Thank you very much from now!

jrecabeitia

Normis, and to this solution.
Thanks for your help

jrecabeitia

Thanks Normis, as I will then comment.

jrecabeitia

I have an RB711 5HN To be updating the firmware, there was a power outage. Now the RB will not start. Can anyone tell me to do to recover it. Thank you all. Tengo un RB711 5hn Al estar actualizando el firmware, se produjo un corte de luz. Ahora el RB no arranca. Alguien puede decirme que hacer para ...

jrecabeitia

Dear, I have a RB1100 who upgrade to v.5.7 The result was very bad. The RB1100, stopped working. The memory is consumed until it stops and does not respond. (single ping) This occurred within a few hours. I went back to version 5.6 Note that changing the values of PCQ was stabilized but not enough...

jrecabeitia

You must use channels 1 - 6 -11 to avoid overlap and a physical separation between antennas less than 1 meter

jrecabeitia

Normis, then with N plates must be used only dual antennas for maximum performance, regardless of the selected standard. Right?

jrecabeitia

That board recommended me to replace RB44G because I am having serious problems.
Thank you all.
Javier

jrecabeitia

normis thanks.
Duda clarified.

jrecabeitia

You can use the USB storage in a RouterBOARD 433, to have a webserver that is accessed from hotspot
Thank you all.

jrecabeitia

Note that both extremes have set the same parameters. Frequency Mode and Country. Country is more non-stop country-set In the images that stuck, it appears that are different. With regard to the selection of country, it is likely that this is the reason why the level of power is so low compared to t...

jrecabeitia

Verify Antena Mode at both ends.
Do not use band 5 GHz Turbo Mode.
Use 5 Ghz.

jrecabeitia

Something very strange ... what is the truth?
RB433 with XR2. "Data rates" default. only G band
firmware v.4.6

AND

Nanostation2. G. Mode only "Data Rates" only 6 Mbits
v.3.5.1rc firmware

RB433 RX Registration Rate "18 Mbits"

jrecabeitia

I accidentally commented a problem that I was presented with a link PTP r52N plates. My setup was based on the selection of waveband N. Change in the 5GHz and lost remote connection. So far so good. But I accidentally set the side stay bridge 5Ghz N only am station-side and 5 GHz and the connection ...

jrecabeitia

Nicomorgan note that modifying the parameter of country, change the frequency ranges you can use. I imagine that the opportunities given to UK may contain an error and therefore does not have the range you need

jrecabeitia

I add other important information to analyze the problem:
With Nstreme
The signal level is -50 / -53
The CCQ 100% TX and RX 1%

Without Nstreme the TX CCQ 100 '% and 100% RX

jrecabeitia

I take a big surprise in yesterday. Having spent my ptp with r52n to Nstreme worked all right for a day until it was shutdown and re-ignition of one of the teams. From that point, the delay went into the clouds and there was no way back. Only be restored when Nstreme deactivated. I'm using v4, 5, RB...

jrecabeitia

What I can say based on my observations, is that between R52H and a plaque NanoStation2 there is no 100% compatibility. This is because if you look at the NanoStation2 its transmission rate at 6 Mbit, we see that the board shows that Mikrotik is receiving 24 Mbps. This can not be. There is an error,...

jrecabeitia

that is using radio plate with mikrotik?

jrecabeitia

When things are so strange, the way that I solved by doing the following: a) Make a backup of the entire router b) Reset default c) Re-build the backup. At least a couple of chances so I could solve similar problems. It's like a bug that is generated within the router's impossible to get otherwise. ...

jrecabeitia

I know that the ROS inspects the contents of PPPoE tunnels and even if they are rules, they work. The issue is that with or without rules, there are connections within the tunnel to pass and others not. For example: Connecting to an SMTP server and / or pop3. Some servers will come and some do not. ...

jrecabeitia

Normis, do not stain or theme idea? It is an implementation that is not to be used? (ip firewall for pppoe)

jrecabeitia

No one has implemented ip firewall for pppoe?
There is no documentation on this?

jrecabeitia

I want to filter traffic ip firewall for pppoe. While inspects is correct, I note that much traffic (pppoe) go to stop, but not observed to be blocked by any existing rule in the firewall. I clarify that I want to do filtering on a bridge ptp, through which pass all the PPPoE connection. I removed a...

jrecabeitia

Hello everyone!
I need payment by snmp to signal levels of the links. Someone knows how to do this?
Thank you!

jrecabeitia

There is a bug in the display of the routing table in winbox, with version 3.24
When a registration mark leads routing, it disappears in winbox, via telnet, but if this registration.

jrecabeitia

Firewall on PC if Windows

jrecabeitia

´Fix frecuency use, on scan list.
Not use SR5 with XR5

jrecabeitia

I find firmware that could be loaded into KN-50 units.
But then more moth, I not find this firmware.
The Maplenet "I-19", is not available.
Other idea?

jrecabeitia

Connect Kn-50 / Kn-51 Turbocell with MT?

jrecabeitia

Could you send it to me also
jrecabeitia@talahenen.com.ar

jrecabeitia

Verify ping from 532 to client and 333 to client
Drop problem from board and panel sector
what frecuency use?
Drop problem on client, because one client with problem, down your system.

jrecabeitia

your antena is for this frecuency? (5260)
Scan-frecuency fixes in 5260
exist bug. if not fixed frecuency, to conect, but the signal is very erratic.

jrecabeitia

fixed scan-list to idem frecuency in AP and Client

jrecabeitia

Ubiquite XR5

jrecabeitia

The Hardware retries is 4, with new version 3.6 / 3.7 produce problem.

jrecabeitia

Help!!!
The RB133 in mode AP-Bridge, register disconnection Station, but the station is not disconnect.
I need to reboot AP to recover this link.
V.3.7

jrecabeitia

Layer7 Protocol
name: SkypetoSkype
String: ^..\x02.............

Mangle
Layer7 Protocol: SkypetoSkype

jrecabeitia

I have your problem. My board cliente is 133C and AP 133C
The SO cliente v.3.4, firmware 2.12 and AP v.3.3 firmware 2.12
I update AP to v.3.4
End problem.

jrecabeitia

Exist any mode for upgrade or upload firmware on XR5 and SR5 from routerboard

Search found 91 matches