MikroTik

Vacadeluna

I believe it may be due to that fact that I moved the DHCP servers over to the VRRP interfaces as well. This means all of the alerts we added were going to an interface not bein used the same way I guess. Personally, I didnt even realize that we did use dhcp alerts until I exported the whole dhcp se...

Vacadeluna

My man! That was it, I moved them to the VRRP interfaces and it has stopped the flood of DHCP entries. I still wonder why it was causing that, its kind of odd.

dhcp-clean.jpg

Vacadeluna

Its funny you say that, when I decided to hit it again lastnight, I noticed the alerts as well and thought to myself. I am actually going to try that next, I just want the stupid dynamic leases to stop popping up lol.

Vacadeluna

So, I have enabled VLAN filtering on both routers and the aggragate switch and trunked all ports including the LAN bridge, and now it appears to be working, but the connection to the routers doesnt seem as table as before. Also the DHCP table is still flodding. I dont think this is an issue with the...

Vacadeluna

I will try this again tomorrow, but I originally did have the bridge in that list as well.

Vacadeluna

I will try this again tomorrow, but I originally did have the bridge in that list as well.

Vacadeluna

Sure I can attach them here, and also you will see here I didnt just turn on VLAN filtering, I also created the VLANs for it which are currently disabled. All VLANs should be tagged as we will be trunking them all down stream to a ag core switch that will feed each individual IDF closet throughout a...

Vacadeluna

Amm0, would you mind removing the Solved, because this has not been solved yet.

Vacadeluna

OK I figured out what killed it. So if I enable filtering on the routers with 0 ingress filtering, router 1 stays up, but r2 never brings any IPs up, its kind of odd to be honest that I didnt see the same results between the 2. Obviously its completely up to you, but I am down to hop on a call of so...

Vacadeluna

sorry ,yes, it was working just fine with VRRP and before I added VRRP. I did enable filtering, and then added the vlans to the bridge and tagged them all on all interfaces on the LAN under interface/bridge/vlans

Vacadeluna

I would love to use VLAN filtering, but the routers seemed to have compeltely killed VRRP now even after disabling it lol. I am going to reboot and see if that helps anything.

Also, I disabled horizon on sfp2 on both routers just in case it caused any p2p issues for vrrp.

Vacadeluna

So I tested vlan filtering and it seems to kill everything on both routers when enabled. I added all VLANS to be tagged on the bridge and the physical interfaces on the LAN as well.

Vacadeluna

Our bridge config is pretty simple, not a whole lot to it, and we are actually not doing any type of VLAN filtering on here, we just loaded all of the VLAN up on the BRIDGE-LAN that we created and leave it at that. I am aware of how to set up filtering, so if that is what we need to make it resolve,...

Vacadeluna

Update, I moved both routers to have dhcp listen on the VRRP interface rather than the VLAN directly, and it still seems to be having the same issue.

Vacadeluna

It is listening directly on the VLAN interface currently. I am moving them both to the vrrp interface instead, as I just tested a single network and it appears that clears it up since it disabled DHCP until needed.

Vacadeluna

Amm0 thanks for the reply!

I have looked and looked, and I dont see where the IP is missmatched on my config, could you show me where that is a little better? That is a /23 so and I decided to use the last usable addresses which would be 3.253 and 3.254. If I missed something, please let me know!

Vacadeluna

Hey all, I have not worked VRRP yet, but we trying to use it to have a backup router at any places that may request to have it. I have a weird issue where every single interface shows an IP address on the DHCP server, and then they will drop off and come back repeatedly. I have set up a floating IP ...

Vacadeluna

BUMP

Need some help asap please everyone!!??

Vacadeluna

So, we have been deploying the hap lites using the script I will be posting below. This script auto generates all wifi information for us, so that our technicians do not have to figure it out and just change SSID, password, and queue limit. The problem I am running into is, we now have the hap AC2 a...

Vacadeluna

Tried with no luck, O well, I will keep at it, but for now, my phone working should be good enough for my needs!

Vacadeluna

I think I now have it!! My only issue is, windows computers cannot seem to connect. I connect on my phone just fine, but windows 7 nor 10 will connect to it. Any thoughts on this?

Vacadeluna

Not sure if you saw the edit or not, but, I was able to get the VPN working with the 2011 being my main router. So, how can I make this work with my Asus router being the main router?

Vacadeluna

How would you suggest I set it up behind my other router? I have a masq rule setup to send traffic out of the "WAN" port. On my main router, I have DMZ turned onto the address my MK is on. My router also has PPTP and L2TP using IPSec passthrough. EDIT: I took my main router out of the equa...

Vacadeluna

Well, if I stay on my main network, and I tell my computer to connect to the address that my VPN router holds, then it works just fine! So, it seems it is only outside of my internet connection where the problem lies. So, my ISP is probably blocking something important....

Vacadeluna

OK, so I posted a while back about trying to use a virtual MK as a VPN server. I have since received a 2011L, and am trying to set it up as a VPN server. I have it set up as a router, nated properly behind my main router. I have tried L2TP with IPSec and PPTP, and have had no luck. It actually verif...

Vacadeluna

Because I use the asus for wifi, and its a pretty good router as well. I would say I could use its wifi in bridge mode, but its a rather expensive device to use just as a switch.

Vacadeluna

So, I have ALL ppp options enabled for passthrough on my asus router, modem is bridged, asus gets public IP. I also have all of these actions accepted on the MK firewall as well. I got you all a shot of the log as well!

Vacadeluna

I may give that a go, for the time being, I just re integrated my asus router and put my modem in bridge mode. So im hoping my ASUS router will allow me to open up the protocol that I need for L2TP-IPSec!!

Vacadeluna

Sorry about that, I thought my web server was working properly, but I guess not. I have uploaded an attachment to show you what it is doing!

Vacadeluna

Vacadeluna

I just saw that it makes it past the verifying the login, and the log on my MK here shows "TCP connections established from x.x.x.x" but then it times out on the remote computers side.

Vacadeluna

I switched to to SSTP, forwarded SSL to my MK and then allowed 443 into my MK as well. I can run torch and see the public IP of the other side hitting my MK. But it still does not connect.

Vacadeluna

Why dont you add a route on the mikrotik that gives it access to the Asus subnet, then just plug PC1 into that mikrotik instead?

Vacadeluna

So, would I be better off going with L2TP/IPSec? I dont think my router from my ISP has the option to open GRE up.

Vacadeluna

Are you talking about your ISPs public address changing that they assign to you? If you are, I would purchase a domain elsewhere, and point your domain to your DNS server. BUT, I would also use a free ddns (or paid) account, and then you can use your web server to redirect to the domain you want to ...

Vacadeluna

I am trying to get a PPTP server up and running for my own personal needs. I have a virtual mikrotik running, and have remote access to it. Every time I generate the PPTP server and try to connect, it always fails. This Mikrotik is behind my ISP router, and I have put the port forwards in as suggest...

Vacadeluna

I have been trying to configure one or the other, which is different at home than for the company I work for. Here is a quick run down of what I have set up so you all can understand to better help me! Virtual Mikrotik running on VirtualBox, behind my ISP router, so it is being NATed. My port forwar...

Vacadeluna

So, I have never actually set up any kind of VPN service (L2TP, PPTP, ETC) anywhere other than here at work where everything is technically on the same network. I am now trying to set up a VPN server on my virtual Mikrotik at home so I can VPN to my house incase I ever need to. I have followed some ...

Search found 38 matches

Re: VRRP - DHCP Entries On All VLANS [SOLVED]

Re: VRRP - DHCP Entries On All VLANS [SOLVED]

Re: VRRP - DHCP Entries On All VLANS [SOLVED]

Re: VRRP - DHCP Entries On All VLANS [SOLVED]

Re: VRRP - DHCP Entries On All VLANS [SOLVED]

Re: VRRP - DHCP Entries On All VLANS [SOLVED]

Re: VRRP - DHCP Entries On All VLANS [SOLVED]

Re: VRRP - DHCP Entries On All VLANS [SOLVED]

Re: VRRP - DHCP Entries On All VLANS [SOLVED]

Re: VRRP - DHCP Entries On All VLANS [SOLVED]

Re: VRRP - DHCP Entries On All VLANS [SOLVED]

Re: VRRP - DHCP Entries On All VLANS [SOLVED]

Re: VRRP - DHCP Entries On All VLANS [SOLVED]

Re: VRRP - DHCP Entries On All VLANS [SOLVED]

Re: VRRP - DHCP Entries On All VLANS [SOLVED]

Re: VRRP - DHCP Entries On All VLANS [SOLVED]

VRRP - DHCP Entries On All VLANS [SOLVED]

Re: AC Wireless On Automated Script

AC Wireless On Automated Script

Re: 2011 VPN Issues

Re: 2011 VPN Issues

Re: 2011 VPN Issues

Re: 2011 VPN Issues

Re: 2011 VPN Issues

2011 VPN Issues

Re: PPTP Issues

Re: PPTP Issues

Re: PPTP Issues

Re: PPTP Issues

Re: PPTP Issues

Re: PPTP Issues

Re: PPTP Issues

Re: Acces to mikrotik router through other router

Re: PPTP Issues

Re: Local address make it public

PPTP Issues

L2TP/PPTP

PPTP Issues