MikroTik

jakkwb

Router is on 7.5. When I try to upgrade from winbox, it downloads, router restarts. Lights all come up, but I cannot access it by ethernet. I have to power cycle it to access it. When I get back into it, it is still on 7.5. I have also dragged the firmware file into the file section and rebooted the...

jakkwb

I would love someone from Mikrotik to at least acknowledge this issue.

jakkwb

jakkwb

So, I need a bit more performance from this. The CPU frequency setting offers choices of:
500
550
600
650
700
750mhz

Is it safe to run this at 750mhz?

jakkwb

Are there any USB wireless devices that will work with this router: CCR1009-7G-1C-PC?

Or any way to get a wireless interface on it to act as an AP so it can be accessed wirelessly using Winbox?

jakkwb

So the Ubnt radio is the problem, or the home router? Should I have the same or different renew times on everything, or does it even matter? Or should I just bridge the Ubnt user radio and let the Mikrotik hand the IP straight to the users router?

jakkwb

Yes that is correct.

jakkwb

Yes, the Ubiquitis in router mode can do DHCP to hand out IPs with its own configured IP pool.

jakkwb

Here is my network: Mikrotik Ether port for Ubnt AP 10.11.12.1 Mikrotik DHCP pool 10.11.12.3-30 to Ubnt radio at user Ubnt AP - bridged 10.11.12.2 Ubnt SM at user - gets IP from Mikrotik 10.11.12.3-30 Ubnt SM at user - in routed mode using DHCP to hand IP to users router at 192.168.10.x Users router...

jakkwb

Yes DHCP server on Mikrotik. I have these IPs set to static after they are assigned to the devices. Ubiquiti AP is bridged Yes DHCP server on Ubiquiti radio to user. Renewal timer is set to 172800 seconds Yes DHCP server on end users router - whatever the default timer setting is. Didn't check it. I...

jakkwb

Hello all. Cannot get any help on this from Ubiquiti. I use Mikrotiks at all my towers, using DHCP to hand the IP to the Ubiquiti radios. The radio is configured to then hand out an IP to the customers router. My problem is this - the radio is reporting the lease to the customer router to be expired...

jakkwb

Anyone care to help me on this?

jakkwb

I actually now have it partly working - I can now access the customers camera locally from both his router and my office. However, we still cannot access it from outside of my network. I can access the test camera attached to my gateway router from outside my network, but not his camera. What am I m...

jakkwb

was hoping someone could give me further instructions to get this to work. cannot find posts with similar problem with examples on getting it work.

jakkwb

The columns his router shows:

External port, internal port, Internal IP address, protocol, Source IP

example:
15000,15000,10.0.0.10, both, (no source IP entered - is this needed? - if so, which router IP do I put there?

jakkwb

The only Mikrotik's doing NAT are now my gateway router, and his home router. I am waiting to get his open/forward commands to see if they are correct or not.

jakkwb

Understood. I now have the Ubnt at the remote end bridged instead.

jakkwb

Well, I understand everyone's recommendations to cloud serve this, it probably would be an easier solution. However, I really want to know how to make this work like I originally asked for future reference.

jakkwb

Hello, I have not messed with customer cameras until now. Basically, network is laid out like this: Internet---Mikrotik gateway (nat happens here - everything past is private IPs)---PTP wireless link---2nd Mikrotik (doing DHCP to customers)---Ubiquiti AP---Ubiquiti M5(router mode and NAT)---customer...

jakkwb

Hello all. I am using 12 of the 13 available ports on this router. I have my main PTP feed on port 1 of this router. This port typically sees 100-175mbps. Ports 2-10 are various PTP radios, etc... I have a Ubnt Powerbeam M5 used for PTP on port 11, and a Cambium EPMP access point (10 wireless users ...

jakkwb

thanks for the input.

So, will this code work with my two cable interfaces? They can either by dynamic or I can set them both (or a single interface) up on a provided static IP. If I leave them both dynamic, both interfaces are in the same subnet and have the same gateway.

jakkwb

Ok, I am already using a static pool for my DHCP. I am also familiar with address lists, as I am using those also.

However, how do I take the IPs in the address list and force them down a certain WAN port?

Thanks for your help!

jakkwb

Ok, I have been waiting on a fiber upgrade since August. Once it is installed, it will look like this: 20MB up/down 10MB down/1 up 10MB down/1 up And the 4.5 will be shut down. You mention dividing the LAN into groups. Can I take my DHCP pool and split it into groups and route each group over a spec...

jakkwb

Yes, all that code is in it, except for the backup routing. Still, the same problems as my last post. Any suggestions? There is no data being transferred to the SL-1 interface. There is very little being received, but it is a steady trickle. Do I need to do something in the code for the sizes since ...

jakkwb

This is a copy from the code above that was suggested I try: I have put in notes about what is happening now after I put the code in: /ip firewall mangle add action=mark-connection chain=input comment=Router_in_out_connections \ disabled=no in-interface=Public-gateway new-connection-mark=\ Public-ga...

jakkwb

Let me clear up a few things - it is kind of confusing:

My WAN connection public-gateway is my ATT connection.

The above router code I listed is me trying to get the ATT and one of my cable feeds working together.

Thank you.

jakkwb

Anyone care to look at this?

jakkwb

The counter for this line in my config is zero (not moving any data): add chain=prerouting dst-address=x.76.133.248/29 in-interface=Office-network Also, the following route is not active (font is blue): add check-gateway=ping distance=2 gateway=x.76.133.248%SL-1 On my Interfaces, my SL-1 WAN is rece...

jakkwb

Here is the export. [admin@MikroTik] > export compact # apr/08/2013 05:40:14 by RouterOS 5.22 # software id = S3YX-FI7K # /interface ethernet set 0 name=Public-gateway set 1 name=SL-1 set 2 disabled=yes name=PTP-to-H set 3 name=Office-network /ip hotspot user profile set [ find default=yes ] idle-ti...

jakkwb

When I try this on the routes with marks and without: gateway = x.76.133.250%SL-1 Both routes then say unreachable Also, this line: add action=accept chain=prerouting disabled=no dst-address=y.76.133.1 \ in-interface=Office-network Will not accept me putting in a subnet mask. The counter on this lin...

jakkwb

I have not been able to get this to work. Here is my export: Its probably something very simple, but I have tried many different configs and have not had any luck. This is PCC with cable-1 and ATT. Once I get those two to work together, then I will try to add in cable-2 (has the same gateway and in ...

jakkwb

OK, I will try it tonite. I tried using the script from this page: http://aacable.wordpress.com/2011/07/27/mikrotik-dual-wan-load-balancing-using-pcc-method-complete-script-by-zaib/ To try to get one of the cable WANs and my ATT WAN to load balance, But a couple of the lines in the firewall chain ar...

jakkwb

I will add some more information to this, perhaps it will help with responses..... I have the following interfaces: Cable1 10MB Cable2 10MB ATT 4.5MB Local PTP I need to load balance cable1 and cable2 so that stations connected to local and PTP interfaces can use the load balanced interfaces and tak...

jakkwb

Hello all,

I have looked for a solution to this, but cannot find it.

I need to load balance two cable modem feeds into my Mikrotik. Problem is, both connections have the same gateway.

Is this possible?

Thank you.

jakkwb

OK, I have had this running for a little while now. I currently only have about 40 IPs using the cache/DNS.

Roughly 350 items in the cache, CPU is now 50%-60% load.

I have a maximum of 13MB of data going through it.

jakkwb

Frego - I am having the same problem with my rb450g. If I turn on "allow remote requests" the CPU almost immediately went to 100%. Now, I was tinkering with it and turned that option from on to off and then on again when the cache had about 400 items in it. (around 200 IPs were using it fo...

jakkwb

Here is a layout of my setup: http://s15.postimage.org/69qeice6z/layout.jpg I cannot access the internet from any IP behind the "PTP to 2nd town". I can access all the equipment including 172.16.16.x if I access it from a radio connected to APs 10.90.90.x. I know this is something simple, ...

jakkwb

Please, someone out there give me a clue how to do this.

jakkwb

Please, can someone help me with this?

I cannot ping the remote router from my office PC, nor can I winbox into it....

I can, however, winbox into the Mikrotik attached to my office PC, and successsfully ping the remote router. What am I missing?

Thank you.

jakkwb

Hello all, I experienced some lightning damage on a wireless setup last night...cannot get replacement parts in fast enough, so trying to get a work-around running for now. What I have: Office-Mikrotik (all bandwidth comes in here) PTP-wireless-link to: remote-tower with 2nd Mikrotik with wireless n...

jakkwb

These two lines have zero on all counters:

add chain=prerouting dst-address=74.193.252.0/22 in-interface=Office-network
add chain=prerouting dst-address=192.168.1.0/24 in-interface=Office-network

Any advice?

jakkwb

OK, I am posting an export compact of my config. Perhaps someone can tell me what I am doing wrong: /interface ethernet set 0 name=Office-network set 1 name=PTP-to-H set 2 disabled=yes name=PTP-to-E set 3 name=Int4-Suddenlink-2 set 4 name=Int5-Suddenlink-1 /interface ethernet switch set 0 switch-all...

jakkwb

Can someone please direct me to an example where this will work? I need load balancing for two WANs that are in the same subnet and have the same gateway.

Thank you.

jakkwb

yes. Right now it is dynamically assigned on both cable modems. I have 5 static IPs with the package (not using yet), but they also have the same gateway IP (for both modems).

jakkwb

If it would help for me to post my config, please let me know.

jakkwb

OK, so now I am taking the same setup from above and trying to load balance 2 cable WANs (they are both the same, 10MB by 2MB) using this method: http://aacable.wordpress.com/2011/06/04/mikrotik-4-wan-load-balance-pcc-complete-script-by-zaib/ Both of the cable modems are handing out IPs in the same ...

jakkwb

Awesome! Thanks a million!

It was late and I was tired/frustrated. I knew it was a type or something simple.

Thanks again.

jakkwb

/interface ethernet set 0 name=Office-network set 1 name=PTP-to-H set 2 disabled=yes name=PTP-to-E set 3 disabled=yes name=PTP-to-A set 4 name=Ent5-Suddenlink-1 /interface ethernet switch set 0 switch-all-ports=no /ip hotspot user profile set [ find default=yes ] idle-timeout=none keepalive-timeout=...

jakkwb

Hello, I have the cable modem attached to this via DHCP client. The port has the IP, the routes have been put in. However, I am not getting any TX from the cable modem, only RX. I know its something simple I am missing....

Thank you.

jakkwb

Or how about a fix for this Mikrotik DNS caching issue:

http://forum.mikrotik.com/viewtopic.php?f=2&t=58243

jakkwb

I would like a fix also, not a workaround. I have three Mikrotiks and all are having this problem.

jakkwb

Well, rebooted the radio that my customers are connected to, afterwards caching on the MK started working....

jakkwb

I already have that in there, as well as have given it a name. It is the first DNS server in that list.

jakkwb

Yes, I went in to each client and released and renewed their IP.

Does this matter: This Mikrotik has a private IP address instead of a public one...Problem?

jakkwb

Ok, I didn't have my reverse DNS entries setup correctly on one of my DNS servers.

Running the command again, it is reporting correctly now.

But, the cache is not being filled. It is still at 33 items, which is what it was after I ran the command.

Any suggestions?

jakkwb

Ok from a Windows machine I ran your command. I got this response: DNS request timed out. timeout was 2 seconds. Non-authoritative answer: name: www.mikrotik.com address: 159.148.147.196 I checked the cache on the second Mikrotik, some entries were added for the request. So why is it not filling up ...

jakkwb

Hello all, I have 2 service towers with mikrotiks at each. One tower is the main, where I get all my bandwidth. It is connected to the second tower via a PTP wireless link. I am running DHCP on both MKs. Also, the primary one has DNS caching running on it, works fine. I cannot, however, get DNS cach...

jakkwb

I found an error in the following line: /ip firewall nat add action=dst-nat chain=dstnat comment="DC/Non Pay Users" disabled=no dst-port=80 protocol=tcp src-address-list=non_paying_cust to-addresses=11.11.11.132 to-ports=8080 The address should be 11.11.11.130 instead. Changed, but it is s...

jakkwb

OK, I scrapped the previous attempts and decided to try using the Mikrotiks web proxy option: I took the following code from this post: http://www.dslreports.com/forum/r23762127-Tech-Ops-Billing-Non-Pay-Redirect Mikrotik Commands: /ip proxy set always-from-cache=no cache-administrator=webmaster cach...

jakkwb

OK, I understand that. I didn't know you could do "not" the address list. That is so cool.

Problem is, there are so many Paypal IP numbers! Is there any way to use the domain names instead of the IP in this setup?

jakkwb

Thanks for the help, Nest,

I understand how to make the address list, but how do I make it a bypass rule?

Thanks again,

Jakkwb

jakkwb

Anyone care to comment on this?

jakkwb

Hello, I am not using Hotspot or Usermanager. I am using the method below to redirect non-paying users to a "pay-me" web site: /ip firewall nat add action=dst-nat chain=dstnat comment="redirect for unpaid customers" disabled=no protocol=tcp src-address-list=Unpaid to-addresses=19...

jakkwb

Hello all, I have an existing network that runs great right now: Cisco 2821 A.A.A.129---switch---DNS1-A.A.A.130, Mikrotik-A.A.A.132 The Mikrotik manages two networks - gateway one 10.90.90.1 with DHCP private IP pool to outdoor wireless customers, gateway two 192.168.100.1 - with DHCP private IP poo...

jakkwb

This is from direct export: Routes of office Mikrotik: /ip route add comment="added by setup" disabled=no distance=1 dst-address=0.0.0.0/0 \ gateway=x.xx.yy.z scope=30 target-scope=10 add comment="" disabled=no distance=1 dst-address=172.16.16.0/24 gateway=\ "PTP to othertow...

jakkwb

I still cannot, however, ping or bring up the web page of the PTP link that is attached to the remote mikrotik. Here is a simple layout of my network: Office PC---connected to office Mikrotik----PTP-system-------remote--Mikrotik(10.90.90.9)---2nd-PTP-system Winbox is running on my office PC. I can u...

jakkwb

Hello all, I have a single gateway mikrotik that handles routing/dhcp/etc...for my network. I have a second remote Mikrotik with a wireless PTP system behind it that I am trying to establish communications with. I can ping this second Mikrotik from the gateway mikrotik using Winbox, but cannot acces...

jakkwb

Can someone please help me with this? I can supply any other needed information.

jakkwb

I changed that number from 1524 to 1500. I have a person on the end of the 2nd-wireless-PTP with a attached desktop. They are still seeing sporadic timeouts and pings over 200 or 300ms when pinging my gateway router. I, however, can ping them with no problems at all. As I said, all wirelessPTP links...

jakkwb

Just noticed this in my config:

2 R ether3-loc2-tower ether 1524 1524

Shouldn't that MTU be 1500 instead of 1524? Will that cause problems like I am having?

Thanks!

jakkwb

This is the output from the 2nd Mikrotik: ip address print detail: 0 address=192.168.168.9/24 network=192.168.168.0 broadcast=192.168.168.255 interface=ether2-loc1-tower actual-interface=ether2-loc1-tower 1 address=172.16.16.1/24 network=172.16.16.0 broadcast=172.16.16.255 interface=ether3-loc2-towe...

jakkwb

Hello, I have had a single PC-based Mikrotik running for a few years now. I have lately added another, and have some issues with it. Here is a diagram of my setup: Internet---PC-Mk----1stwirelessPTPlink------2nd-Mk----2ndwirelessPTPlink------otherPCs All IPs once they get past the PC-Mk are private ...

jakkwb

I'm not exactly sure what you mean by that? The UPS is new. It is powered and charged. Just there to do its job. I checked last night and I have the lower powered 12v adapter powering this router. Should I try the 24v one? I read on another forum page that the 750g uses a lot of power, and under cer...

jakkwb

I've got a 12v 1a. Not sure if it has a M connector on it, though.

jakkwb

Or perhaps do I need the higher amperage power supply: 24HPOW for this router?

jakkwb

Hello all,

I have the above mentioned router. I have it on a UPS, but every once in a while it will lose power. I have to unplug and replug it several times to get it to come back on.

Does this sound like a power supply issue or a problem with the router itself?

Thanks.

jakkwb

Anyone give advice on this?

jakkwb

I am doing something very similar. Questions: I am using ATT T1s and Suddenlink cable combined for about 15MB of access. Do yall recommend a in-house DNS server for both providers? I have them setup for ATT, which was my original provider, but have wondered about whether it would help for the Sudden...

jakkwb

Hello again, can someone please tell me what I am doing wrong on this setup?

Thank you.

jakkwb

Here are the configs of both Mikrotiks. I will put them in seperate posts that way it will be easier to read. Please forgive, I am mostly a newbie at this. Any knowledge I can gain by this will be stored and put to use. Mikrotik (750g) at Tower A: interface export set 0 arp=enabled auto-negotiation=...

jakkwb

I now have most of this running correctly, except: From a workstation at my office - pinging to the PTP radio (the closer end of the PTP link to tower B) on tower A thru the 750g also at tower A - ping works about 90% of the time. The other 10 it will report that the "reply from 192.168.168.1: ...

jakkwb

Never mind... the counters on the interface list are always zero. But when I opened up the interface window, the numbers are changing. Not enough data passing I guess.

Thanks again.

jakkwb

Thanks for the help. I can now successfully ping and access the radio on tower A that will be one of the radios to supply a PTP link to my remote tower B. The 750G has software load 4.13. I have the above radio on Ether3. Strange thing is: from my office, I have the radio web page up, and I am pingi...

jakkwb

Here is a current layout of my network: Cisco 2821 for incoming bandwidth Mikrotik PC router on public IP (handles DHCP and NAT for my wireless network) PTP link office end - everything from here down on private IP block 192.168.168.x) PTP remote end (at tower A) switch APs - get private IPs from Mi...

jakkwb

Hello all, At my main office I have a PC based Mikrotik router that handles a PTP link and DHCP services to a remote tower (tower A) that has wireless Internet service running on it. It is running fine with no issues. All IPs on tower are private. I am trying to get service running on a second tower...

jakkwb

Hello, I am considering getting some cable broadband access to go along with my 2 T1s. Cable would be from a different provider than my T1s with static IPs. Am using MK Pc router box for passing IPs to my wireless clients. Want to know if I can have Mikrotik redirect bandwidth intensive page request...

jakkwb

Can anyone out there please help me on this or forward me to some information about optimizing Mikrotik and its firewall?

jakkwb

One other note: I use Winbox most of the time for management. It does sometimes show the CPU to be 90-100% - it jumps around. However, I can close Winbox and reopen, and it goes back down to normal.

jakkwb

I have a lot of stuff disabled for experimentation: Here is my complete firewall filter print: 0 ;;; Drop Invalid connections chain=forward action=drop connection-state=invalid 1 ;;; Allow Established connections chain=forward action=accept connection-state=established 2 ;;; Allow related connection...

jakkwb

I used the nearest server to me: (from my workstation)

1.1Mbps down
.27 up
26 ms ping

I was trying to stream a 20 minute show from Hulu. Like I said, it did some better with the Firewall virus check off.

jakkwb

Hello all, I am a small WISP with some clients who are trying to run streaming video, both live and non. I have 2 T1s for access. during peak times it has gotten to 2.7Mbps peak. For the most part, my load hovers around 1.5. Clients always complain about constant stopping and buffering. I am current...

jakkwb

I managed to find the problem and fixed it.

Thank you!

jakkwb

Hello all, subject line says it all. Changed my whole IP scheme, now I cannot ping Mikrotik from any other machine on my network. Trying to get Winbox working again, too.

Please help,

jakkwb

jakkwb

OK, I think I understand it. I have a few more questions. Here is my currrent filter list: 0 ;;; port block warning chain=Virus action=drop dst-port=1434 protocol=tcp 1 chain=Virus action=drop dst-port=1434 protocol=udp 2 chain=Virus action=drop dst-port=2745 protocol=udp 3 chain=Virus action=drop d...

jakkwb

Anyone? Surely someone out there knows how to do these things.

jakkwb

Hi all - Subject line says it all. I just started my web proxy on Mikrotik 2.9.51. I am still very much a newbie with Mikrotik. Anyway, I have only 5 machines with web-proxy configured on. However, it is reporting 7 clients. I need to know how to restrict access to just my IPs, both public and priva...

jakkwb

Thank you for your input - What I am asking is this: When my Mikrotik assigns an IP using DHCP server to a customer, should they get the Mikrotik itself or my inhouse DNS server as primary? Then should I also assign a secondary (in-house DNS or MT) or leave it blank? I want to make efficient use of ...

jakkwb

ok, please tell me this about my Mikrotik setup: (Using Winbox) In the IP-DNS-Settings-Primary DNS - Which should I put? The IP of the Mikrotik itself, the gateway router, or my inhouse primary DNS server? What about the secondary on this same screen? Then, in my IP-DHCP-Server- which should I put f...

jakkwb

"If so then this must be the only box that references an external DNS server"

Can you tell me why this is?

Thank you.

jakkwb

ok - but should I set the primary DNS to the Mikrotik itself? Wouldn't that give a somewhat better performance since it will use its own cache instead of looking elsewhere? Or leave it like it is? I just want to get every drop of performance out of this box by every means possible. Thank you. Is the...

jakkwb

OK, I upgraded to 2.9.51 tonight. Rebooted - Cache is steadily filling up.

I'll post any changes.

jakkwb

I just didn't know if this was normal or not. It "seems" to be running fine. Here is a diagram of my layout: Ethernet0 - to Ethernet switch (to Cisco Gateway router & Primary DNS sever) Ethernet1 - to Wireless PTP Ethernet2 - to wireless PTP (uses DHCP/NAT) Ethernet3 - to office networ...

jakkwb

Hello all - Am running a PC-based Mikrotik box - 4 Ethernet interfaces, for various ISP/WISP functions/customers. I have version 2.9.43. I have "allow remote requests" checked. I have the cache set to 10240, which is the maximum it can be. I have a primary onsite DNS server, which I have l...

jakkwb

Actually, I have my main group of IPs split into 4 subnets. It is a class A address subnetted into class C.

Those are not the real IP numbers.

Thank you.

jakkwb

Anyone care to tell me why the above is happening?

jakkwb

Scott, quote: add chain=virus protocol=tcp dst-port=1024-1030 action=drop comment="don't \ know" disabled=no I did find that earlier and disabled it (see my above posts). That fixed my Office-network web pages loading. There is still something wrong with my PTP-H - I still cannot get web p...

jakkwb

As you can tell, I have been messing with it all day long. I changed the IP information for the Office-network. Also changed that NIC card (it seemed a bit flakey) Anyway, there are a few pages now and then that come through (via a remote PC connected to a Motorola Canopy radio on the PTP-H interfac...

jakkwb

There are no route rules. Here are the routes: Terminal vt102 detected, using multiline input mode [admin@MikroTik] > ip route print Flags: X - disabled, A - active, D - dynamic, C - connect, S - static, r - rip, b - bgp, o - ospf, B - blackhole, U - unreachable, P - prohibit # DST-ADDRESS PREF-SRC ...

jakkwb

Please help me. The web performance on the PTP-H is dismal. Something is wrong with my setup, but I do not know what it is.

Anyone?

jakkwb

please, someone help me with this....

How can I test the NIC cards in Mikrotik?

jakkwb

Thom, hi again. After I disabled all the other filters, I waited a bit then rebooted the router. I do not have a hotspot, this PTP is a wireless PTP to a Motorola Canopy tower. I can ping from a remote Canopy connected PC using IP or domain name successfully. I can also ping (ip or name) from Mikrot...

jakkwb

Thanks for the tips, Thom. I actually found the rule that said to drop all UDP last night after my last post. After I disabled it, one of the interfaces started working (Office-network). The other, PTP-H, still does not bring up web pages. It tries - sits for several minutes as te progress bar slowl...

jakkwb

ok, here it is: # nov/14/2007 20:54:45 by RouterOS 2.9.43 # software id = DQ5H-6XT # / interface ethernet set Public-gateway name="Public-gateway" mtu=1500 \ mac-address=00:10:4B:C5:25:68 arp=enabled disable-running-check=yes \ auto-negotiation=yes full-duplex=yes cable-settings=default sp...

jakkwb

Yes, that actually is enabled under the default profile, but I am not using wireless or hotspots on this router.

Advice?

jakkwb

post a traceroute from your clients: from one of my office machines that can ping/tracert, but cannot get web pages: tracert yahoo.com 216.109.112.135 first hop 172.16.1.1 (office-gateway NIC on Mikrotik) x.y.z.1 Cisco gateway router (nothing changed on this machine at all - has always worked perfec...

jakkwb

Hello all, I have Mikrotik running with 4 nics. I don't know how to export my configuration (yet). It was running fine until earlier today. Do not know what happened/changed. I have 2 DHCP servers running on 2 of the NICs. They both hand out/assign IPs with no problem. DNS servers are also registere...

jakkwb

What version are you running? If not current then upgrade. 2.943 What happens to these routes when you reboot the router? nothing. Same thing Do you have bridging setup on any interfaces? no bridges at all. Anything else you haven't told us that might be relevant? I can't think of anything. I will t...

jakkwb

Would someone please help me out with this? I found this post:

http://forum.mikrotik.com/viewtopic.php ... ref+source

It seems that the "pref source" might be a possible bug in the software.

Has anyone dealt with this before? I need to have it fixed.

jakkwb

Thanks for the tips. Here are my corrections: ip address print: #__ADDRESS__________NETWORK_______BROADCAST_______INTERFACE 0 ;;;added by setup __100.101.102.4/26____100.101.102.0____100.101.102.63____public Gateway 1_100.101.102.129/26__100.101.102.128__100.101.102.191___PTP-B 2_192.168.1.1/24_____...

jakkwb

What would help a lot is to be able to change this dynamic route below:

DAC 192.168.1.0/24 (blank) 100.101.102.129 0 PTP-B

The interface needs to be OFFICE-NETWORK instead of PTP-B

I don't know why it is setup that way.

Please help me fix this.

Thank you.

jakkwb

Hello all, please forgive my newness to this. I am learning as i go. I have a full class C of public IPs. lets say 100.101.102.x/24 My gateway Cisco router is at 100.101.102.1 My Primary DNS is at 100.101.102.3 My MT router is at 100.101.102.4 The MT router has 4 NIC interfaces on it. They are: publ...

jakkwb

ok, I still don't know if the demo license supports radius pass through or not. I can only assume it does, but like I said, I went ahead and purchased the next level license anyway. Turns out, I had forgotten to enter the secret key for radius for the MT router into my radius client file. It started...

jakkwb

In the radius button on the left side of the WinBox / MT console. I have PPP and login checked. Called ID box is unchecked and empty (I have read a post where it cannot be blank, or it will not work at all). I have my domain in the domain box, and checked My Radius server IP is in the address box I ...

jakkwb

I just purchased the level 4 license. Rebooted. I am still not getting radius requests/replies.

Any suggestions?

jakkwb

OK, I just purchased the level 4 license. Still no radius.

What gives?

jakkwb

yes, it is a point to point link That part runs fine, and has for years. Mainly it is the radius authentication that I need to get working.

jakkwb

not exactly. This is what the Ascend max looks like: http://cgi.ebay.com/Ascend-MAX-6000-Remote-Access-Server-MX60-4T1-32-AC_W0QQitemZ260131172146QQihZ016QQcategoryZ162QQssPageNameZWDVWQQrdZ1QQcmdZViewItem it is a remote access server via dial-in for ancient dial-up ISPs. here is a diagram: Ascend M...

jakkwb

Hello folks, just a simple question. I am currently running an evaluation MT server (see my other posts concerning DHCP). Will the registered demo license support external radius authentication? On one of my interfaces I have a wireless PTP link attached and working fine. On the remote end I have a ...

jakkwb

ok, I added more RAM, it seems to be running fine now. On one of my interfaces I am running a wireless PTP link. On the remote end I have a Ascend MAX with dial-up internet access. I have a central Radius server setup here at my main location which authenticates the remote MAX box users. However, si...

jakkwb

Yes - I finally found that masquerading was required for the local machines to "see" the outside world. After I entered the command, it started working correctly. However, the performance seems a bit slow. Is there anything I can check concerning performance? This MT box I am building is g...

jakkwb

update - OK, I didn't have my subnet mask declared in the address list page for 192.168.1.1 I put in 192.168.1.1/24. Now from the Windows PC attached to a switch attached to that interface (I named it Office-network), I can ping the gateway (192.168.1.1), I can ping the MT router (68.95.x.x). But I ...

jakkwb

I tried running the wizard. Any type of IP pool I try to enter in the addresses to setup box, I get an invalid pool message. I am trying anything, such as 192.168.1.2-192.168.2.100. So instead of using the wizard, I just went through and manually set it up. Using the wizard - Am I supposed to put an...

jakkwb

Good day all, I am somewhat of a newbie at this, so please be patient with my explanation: I am setting up a Mikrotik router using a PC. Lets say it is at IP 1.2.3.4. ( I actually have a full block of class C). I have another NIC in it that I have assigned 192.168.1.1. I am trying to set that interf...

Search found 133 matches