This still doesn't work. After changing it to 200, it doesn't report a down when losing all packets. Status: up Since: Nov/16/2022 09:03:01 Done Tests: 26 Failed Tests: 0 Sent Count: 10 Response Count: 0 Loss Count: 10 Loss Percent: 100.0 % RTT Avg: 0.000 ms RTT Min: -0.001 ms RTT Max: 0.000 ms RTT ...

Thankyou. However, this is poor design. In theory, if the field is 'not enabled' and has 'no value set' then it shouldn't be used when determining if the test result is UP/DOWN. If this field is going to be used regardless in determining a UP/DOWN result then it should be a mandatory field with 100m...

Hi, I am having trouble with the new Netwatch, I am trying to monitor if my Wireguard-VPN is up and passing traffic. I created a simple static route for example 8.8.8.8/32 through the Wireguard-Gateway, and 2nd rule for 8.8.8.8 as a black hole. I am using a ICMP Netwatch check. Configured as: Host: ...

Simply READ carefully pervious post...

The post is not clear. It does not state where to add it.

The correct answer would have been:

Add :global pushover in the script you are calling $pushover in.

No need to be a dick.

$pushover message="xyz" does work in terminal, but it doesn't work in scripts

update：
add
:global pushover
and I can use $pushover now

Hi,

Where did you fix this? I am able to send using terminal but not in from inside of scripts….

Can you tell me which line to changed?

Thanks.

Have installed a few of RB4011, yes - only one screw. Looks like this is by design.

So the brackets were still loose after you tightened the 1 screw?

I am worried about going to over tighten and break the screw...?

I just upgraded my RB3011 to a RB4011 and the brackets on the 4011 are very loose but I only see 1 screw hole to affix to the router on each bracket… is this by design or am I doing something wrong…..?

6.48 beta58 randomly starts dropping traffic. DNS looks ups are fine Some sites load others don’t. After a reboot suddenly starts working again for a few hours then stops again. Reboot fixes it. Internet is up, no packet loss, dns working, disabled fast track, enabled fast track, checked route cache...

Hi, I am trying to get a VPN up on my mikrotik, and its working well -- however I am in the nightmare of Netflix which I am trying to *EXEMPT* Netflix from passing through the VPN. I want to stay in my geographic area and route the traffic directly through my ISP. I have successfully whitelisted the...

Thanks bpwl

You are correct. This fixed it.

Would you be so kind to post the default rate config?

Hi, I have 2 stand alone APs at work which have no problem to accomplish 650-866 Mbps @ 80Mhz/2S/SGI however at my home environment I cannot accomplish more than 80MHZ/1S/SGi @ 433 Mbps on the exact same devices using CAPsMAN. What am I doing wrong? I have posted my config below. Any ideas? # jul/22...

Hi, I am running 6.46.6 May/16/2020 12:19:21 lte,async,raw WAN-LTE: sent AT!GSTATUS? May/16/2020 12:19:21 lte,async,raw WAN-LTE: rcvd !GSTATUS: May/16/2020 12:19:21 lte,async,raw WAN-LTE: rcvd Current Time: 64319\0x09\0x09Temperature: 35 May/16/2020 12:19:21 lte,async,raw WAN-LTE: rcvd Bootup Time: ...

Hi, I have a Sierra Wireless 330U LTE USB card connected to my X86 ROS. I am able to connect fine using the LTE interface (not a PPP connection) and pass data without issue. However soon as I attempt to send a text message using the LTE interface the whole LTE interface drops and disconnects - needl...