are you sure that your default gateway is the 192.168.1.1?
Mikrotik's DG is 192.168.88.1
If you're sure, then in the screen saying: "your connection isn't private", hit "proceed anyway"!

either i connect them via L2TP or PPTP, i cannot ping devices between the two networks, not just windows pc, anything. can i configure an EoIP with DDNS?

what i want is: LAN1 can communicate with LAN2, not being on the same LAN.

Hi everybody. I'm looking forward in doing something a little bit out of my knowledge i think. I have 2 MT's, both under the same ISP and miles away from each other. I want to connect them (via PPTP, L2TP, IKEv2 or whatever) and make them work as one network (meaning that one PC from the one side ca...

oh i see, thanks again, next time you need an advice i hope there's someone kinder to answer you!

As always, the forum solved my problem. You are both right, the rule should concern both 1wan and pppoe-out interfaces since i have a modem connected to ether1 of my router. So if i set the in-interface-list to WAN in my already existing rule or keep the rule as is and create another with in-interfa...

Already checked it but nope, nothing. That's why i know for sure that it's not a server problem (windows FW etc.)

Yes it has a dynamic public IP. Truth is i had it working 2 months before in another setup which unfortunately can´t access right now. I don´t remember the rules i had back there though. I remember clearly that i had the already active rule (the one you referred to also) but can´t remember anything ...

I have a little problem on accesing my plex server from outside my network no matter what methods i've tried. Searched a lot but no solution found, so i'm posting my FW configuration with the hope that someone helps me out! Server has a static IP (192.168.10.101) and plex shows the message "Not...

So i have made a setup earlier and i have a problem i can't seem to figure out. I think it just need some route rules though. I have 3 different bridges: 1)bridge: contains 1 physical interface (ether5) and 1 logical (l2tp_1) and is configured with 1 network (192.168.10.1/24) (belongs to LAN_1 inter...

Hello friend. If you refer to:
/ip service
set www address=192.168.88.0/24
then it's for browsing via my vpn. I have specified the subnet that i want to browse so as the rest cannot.

Oh yes i do know those things, have already read those stuff. I've made some changes based on your instructions and i'm posting below my new config, if not a problem, can you read it and advice any other changes? Mostly on my security, the other stuff i think i can handle! # may/29/2020 09:49:16 by ...

what do you mean by c net? i have a few fixed-ip and only left 10 addresses in the dhcp pool for the devices that's not always connected. the fixed ip's are for devices that are always on!
Thank you again for your time, always good to learn from experienced people!

i just dropped 1723 and 443 and left open only the 3 needed (500, 1701, 4500).
Anything else that's wrong in my config and leave me vulnerable?
Many thanks in advance!

if i drop this one, what's going to change? will it affect the current situation or just block the attacker?

My VPN connection is a L2TP. Not a PPTP. I don't know why PPTP is open. I'm posting below my config 'cause i'm new and may have some mistakes! # may/29/2020 07:49:53 by RouterOS 6.46.6 # software id = C8B5-GX6M # # model = 2011UiAS-2HnD # serial number = xxx /interface bridge add admin-mac=xxx arp=p...

i should also say that i have an always active vpn connection to my router, although i don't know if that has anything to do with the above logs!

Hello everybody. I'm posting a photo of part of my log below. I keep getting those logs (there is no pattern like in a specific hour or something like that). The IP's differ every time, what's happening? is anyone attacking me? how do i stop this?

So it seems that there isn't any situation to fix the problem permanently. Personally, i did the following and fixed this problem, although it has a gap since i lose about 3 minutes of connection. Windows 10 will hangup the connection at exactly 7h36m16s. I did checked it over 5 times. I already had...

so i tried some solutions out and it seems that with a few changes in the windows firewall, i managed to get access to the pc which i use as an FTP server from the network discovery via my VPN. When connected to VPN, windows network discovery can't recognize the PCs in the network but if i type the ...

thank you very much for your help. problem solved!
Is there anything else i can do for the network discovery? I am planning on building up a very tiny home file server in an old pc i have!

thank you for your answer. i posted below my config file with all the sensitive data hidden. although i should mention that i'm a newbie and learning most things right now. so my config is very possible to be messed up. if that's true, i don't have problem to reset the router, make some basic config...

Hello. I've have set a VPN over my MikroTik RB2011UiAS-2HnD. The LAN has adresses in the pool of 192.168.88.0/24 (DG: 192.168.88.1). The VPN doesn't have a pool (i don't want one), it only has one adress the 192.168.89.100. My problem is that over VPN i can access all of my devices (for example the ...