MikroTik

artist1

Thanks leonj, upgrade is what i need.

artist1

Hi all. Is it possible with script to block wireless users with low signals and optionaly show them message why they are blocked until they have better connection? I want mt to ignore all wireless users with lower signals than -75dbm. To ignore them is just fine, but if possible it would be nice to ...

artist1

Hi.

I have ip phone from my isp. I found that MT can be a phone central. All i can find about that in "how to" section is the oposite way. Examples are from pstn line converted to ip phones.
Now i would like to convert one IP phone line to multiple pstn lines. Would that be posible?

Tine.

artist1

PC is athlon 1700+ with 256Mb DDR, 1 lan card and 1 wireless card. Hotspot setup is just basic with hotspot login.. (x.19 version of mikrotik and had the same problem with last 5 versions) "Error: 504 Gateway Timeout" is what i get after hotspot is 4 hours online.. Slow responding or no re...

artist1

Hi all. Im expiriencing hotspot slowdown after few hours of working. I tryed all kind of setups, but always the same. What could i miss with the wizard? Is there any other trick? What could slow down responding, resolving pages? Uploads, downloads, msn, internet radio, all work great, showing pages ...

artist1

Or how to limit users loged on HS with same user/pass to share bandwidth of one user?

artist1

Hi. I have problems with basic hotspot system. It works in intervals,and sometimes i need to double-click links on google to open them. All users have -60/-70 dbm signal, hotspot is installed on 1700+ athlon with 256Mb of ram. Max is 7 users at the moment.. I dont know why, but often it waits and wa...

artist1

Ok, but if 2 clients sign in with same user/pass, then their bandwidth would be double right? I want them to split bandwidth of one, coz they use same user/pass... And i would like to set them 1meg for 4minutes, and after 4mins only half of that. Is it posible to make one queue for all usernames wit...

artist1

Hi all. I have latest MT on my hotspot. I wanted to limit each user or better each username for certain bandwidth. I did it with added ip to every HS user and then simple queue for that ip. Queues dont work for all users, but work for some of them - and they are all the same.. I dont understand why....

artist1

Go to hotspot menu and press setup. Follow the wizard.

or type in console

/ip hotspot setup

and is the same.

artist1

I cant find anywhere if this new chipset is supported in mikrotik?
AR5005GS (AR5214A) I think this card is newer than the mikrotik manual, so is it posible to be accepted as previus atheros models?

Thanks....Tine

artist1

Which card does provide noise information?

artist1

Check your local store...

artist1

Its true, also level1 wnc0100 works and netgear wg311t . I have tested them, they work perfect with 26dbm, 30dbm setup makes latency unstable and netgear card gives out 5W instead of 1W (on 30dbm setup), but is unusable.
The power was measured with osciloscope and spectral analyzer.

artist1

You need to buy them with extra license from mikrotik...

artist1

Time outs are comon in wireless. Your link is bad, too much noise, other interferences or weak signal causes this.

artist1

@Coyote

There is no SR3 card.. SR2 works on 2,4Ghz and SR5 works on 5Ghz, these two cards are 400mW with -98/-91 reciving sense. SR9 is dualband card 60mW.

artist1

Jep i tried 2.9.5 and it works. Thanks!

artist1

I have NETGEARS wg311T atheros wireless card. I read somewhere here on the forum that this card is bad, Its recognized by mikrotik(2.8.25 ver.) as an AR 5213 but it doesnt work at all. I tried 4 of them, not all can be bad. They work in PC. I have the same chipset on LEVEL ONE card that is working j...

artist1

http://forum.mikrotik.com/viewtopic.php ... ight=#9690

I had this with msn, dont know about other things.

artist1

Gain with antennas is much higher than with amps, so no problem to that link is my opinion. Hard to say about the speed.

Im working on a record in our country with 146km link, 42dbi 180 dishes, i calculated full speed, how much i will get i will tell later

artist1

Thanks guys, it works fine now!
Mikrotik forum rocks!

LP......Tine

artist1

plenty, but none that will help until we know more about your network configuration.. Is the network NAT'd? what do your firewall rules look like, specifically the forward chain. might as well copy the src/dst-nat rules as well. Omit ip addresses. PLS share ur ideas with me, coz im desperate. LP......

artist1

My configuration is very basic: /interface enable ether1,ether2 /interface pppoe-client add interface=ether1 service-name=adsl user=xxx password=xxx disabled=no /ip address add address=192.168.0.1/24 interface=ether2 /ip firewall src-nat add out-interface=pppoe action=masquerade /ip firewall rule in...

artist1

Still no luck. What could block the thing? Port test fails and i get low id!

I dont wana block others for p2p downloading, just i dont care if they got low id, but i def. want high id at least for myself

My isp allows the p2p connections.

Any ideas?

artist1

I tried, but no results. When i test ports with emule i dont pass.
Can you be more specific?

tine

artist1

What is the simplest way to open emule ports for only one computer on the network?

artist1

The chain syntax wasnt recognized, so i got an error message.
Then i played arround with winbox and configured something like u send me and it trully started working!

Thanks alot ANdrew

artist1

Hi!

I just managed pppoe client on MT, but now msn is blocked.
When i was testing the router on my network it worked just fine.
Whit same settings and pppoe client added to the router, nobody can sign in with msn.

PLS help.

Tine

artist1

Well thanks, i managed somehow to fix the problem, i trully didnt see that help chapter.

TY

artist1

Hi everyone! Im sorry for being a dumbass, but i cant figure out how to configure the router to login on my isp adsl and hold the line. My clients are wireless clients, but i dont use wifi from MT, i just connected netgear wg302 to ether2. So im using MT for holding the line, bandwidth management fo...

artist1

Name - 2.201/32 Target Address - 192.168.2.201/32 Limit At - 65536/131072 Max Limit - 262144/524288 Burst Limit - 393216/786432 Burst Threshold - 262144/524288 Burst Time - 90/180 Im noob at mikrotik, just purchased the key, and my router rocks with settings u gave! :D I have a question maybe in wr...

Search found 32 matches

Re: low signal redirect/disconect

low signal redirect/disconect

IP phone question

Hotspot problem

Hotspot problem

hotspot bandwidth limiting

Atheros AR5005GS

wg311T problem

emule ports

MSN BLOCKED

PPPoE