MikroTik

nannou9

Still issue on rb4011 with rc3 with vlan and bridge hw offloading. Created SUP-118205 with supout file. Will post updates if I get any response. Got response from support team. My issue was that my bridge interface had pvid set to the same value as vlan id. As soon as I reset it to default 1, all s...

nannou9

Still issue on rb4011 with rc3 with vlan and bridge hw offloading.
Created SUP-118205 with supout file.
Will post updates if I get any response.

nannou9

Just tried rc1 on my RB4011 with single vlan spanning on both chip ports and sfp and it fails. Had to revert to 7.7 immediately.

nannou9

In case if anybody has misbehaving rb4011 using vlans, please make sure you have MSTP enabled on bridge.

Didn’t work in long run. I tried also disabling hw offloading on bridge ports or enable ign snooping as someone suggested and none of it helped.
Gave up and reverted to 7.7 again.

nannou9

In case if anybody has misbehaving rb4011 using vlans, please make sure you have MSTP enabled on bridge.
Interestingly I had RSTP used previously and all was working fine on 7.7 and older.
Took me some reading to find it.

nannou9

Waiting for audience refresh please! Hope there is one in works.

nannou9

I had to revert to 7.7 as since I upgraded to 7.8 I started having issues with my Lightwaverf Link Plus hub (which is about 5yo IOT device)- mostly not working, showing as disconnected from internet etc. suspect might be DNS related? Restarting my RB4011 router to which it is connected by wire didn’...

nannou9

Cloud backup stopped working for me on all 7.6 devices( rb4011, crs305, audience)
Says error from apis.
Was working on 7.5.

nannou9

Where are our posts from the weekend???
Forum was down yesterday. Assuming you have guys restored from backup and they are lost?
Just guessing, log4j cve issue?

nannou9

My audience wifiwave2 is finally stable on latest rc builds.
It has been very unstable on betas, dropping clients sometimes every few minutes.
Thanks for fixing this!
I haven’t spotted however anything on any tv release notes which would explain improvement.

nannou9

I have HP 107w printer at home. Haven't been using it for a month but it was working fine on betas. Now however I cannot connect to WIFI anymore. My short config: set [ find default-name=wifi1 ] channel.band=2ghz-n .width=20/40mhz configuration.country=Malaysia .mode=ap .ssid=XXXXXXX disabled=no sec...

nannou9

Are you using the wifiwave2 drivers nor CAKE/fq_codel/CoDel queues in your Audience?

Using wave2 and simple vlans. Can’t paste my config as I am away and have mobile only.

nannou9

Audience is crashing regularly- like every 10-20h.
No support file created weirdly.
Changed to persist logs so will update you soon.
RB4011 is ok however.

nannou9

Have you created a support ticket about it? I though this thread is good enough to report a bug/issue. But as you are asking for it it sounds like it isn’t. I will raise support ticket separately. Thanks. But this is then slightly weird. Are you telling me that all the problems reported in this for...

nannou9

Hopefully the wait for next beta will be worth it and it fixes Wifiwave2 issues where my wifi sometimes goes down every few minutes on my audience. I have reported this multiple times with logs and config export already. @Normis I also asked for comment few times from MikroTik on this, no answer so ...

nannou9

Thanks to MikroTik for honest summary.
Looks like few users enjoy 7.1b7, any reason why it is not official?

nannou9

My wifi1 phy is going down multiple times a day. It is very unpredictive. There are days where everything is fine, others it is dropping all clients sometimes multiple times per hour. Only reset helps and sometimes it is close to unusable. This has been reported multiple times and is present in beta...

nannou9

Hi,
Try export verbose

nope, nothing.
Besides, my understanding of verbose is that it is printing defaults?
But my value is not default.

nannou9

/ip/firewall/mangle/export doesn't work correctly for mark-routing action. Did you add the routing table named "via-gw" first? It doesn't let you mark-routing for a routing mark unless that mark matches the name of a routing table defined on the router in v7. Yes it is there and working c...

nannou9

/ip/firewall/mangle/export doesn't work correctly for mark-routing action. I have added rule add action=mark-routing chain=prerouting comment="via WG" dst-address=0.0.0.0/0 passthrough=no src-address=10.0.0.0/16 new-routing-mark=via-gw but it is exported as add action=mark-routing chain=pr...

nannou9

On my Audience I am still getting wifi1 (2.4GHz phy) dropouts. The is happening consistently throughout beta 4,5,6. All my clients are down and unable to reconnect. In logs like 20 last messages for wifi1 are: "@wifi1 disconnected, group key timeout." Nothing special in my config: # jun/27...

nannou9

Hi Guys, I am nowhere close to an expert, rather hobbyist. I have WireGuard Server on RB4011 to which I can connect from my mobile. I can even see my requests being routed from my mobile to other devices in my network using torch- like through VPN trying to load Audience AP WebFig. So it is like: Mo...

nannou9

Ah, got it. Looks like the app falls back to userspace implementation if the wireguard module is not loaded...
So this worked:

Well done mate

nannou9

Well, you still need to run the nordvpn app to extract your private key... Though this can be done in a virtual machine I guess. I will give it a try. Thanks! Correct, this is exactly what I did as they require Debian or RHEL family while I am big fun of Funtoo (Gentoo). You do t need X so minimal ...

nannou9

Yes, please! I think NordVPN uses something on top of wireguard and calls it "NordLynx"... Having the details here would much appreciated! See 1st post here: https://forum.openwrt.org/t/instruction-config-nordvpn-wireguard-nordlynx-on-openwrt/89976 Private key goes to the wireguard interf...

nannou9

Just installed yesterday on RB4011 and using it now with NordVPN wireguard (not officially supported yet on MikroTik). Works really well, getting full 550MB internet speed.
Cpu jumps up 70%, but that is fine.
If anybody is interested can post instructions.

nannou9

It’s about time for next beta.
Let’s hope it improves wifi stability.

nannou9

My Audience 2.4GHz network is crashing frequently every few hours to every few days- this is consistent behaviour for beta 3/4/5 for me. No idea what is causing it as there is nothing special happening- not adding any new devices, nor removing anything. So not sure why it sometimes crashes after fe...

nannou9

They are doing the right thing (I hope) stabilising core. 7.1b5 is still crashing frequently on many devices (sometimes multiple times a day on my Audience), same with wifi. So they are (I hope again) focusing on core features, without which it makes no sense to use it at all. Otherwise you would ha...

nannou9

try netinstall

Sorry for noob question, but how netinstall is different from factory reset?
I mean I know what netinstall is, but just not sure why it would make a difference vs factory reset.

nannou9

My Audience 2.4GHz network is crashing frequently every few hours to every few days- this is consistent behaviour for beta 3/4/5 for me. No idea what is causing it as there is nothing special happening- not adding any new devices, nor removing anything. So not sure why it sometimes crashes after fe...

nannou9

My Audience 2.4GHz network is crashing frequently every few hours to every few days- this is consistent behaviour for beta 3/4/5 for me. No idea what is causing it as there is nothing special happening- not adding any new devices, nor removing anything. So not sure why it sometimes crashes after few...

nannou9

What to do, when my Chateau12 hangs up / freezes after 5d of uptime without problems? What can I report to support? No unusual usage, suddenly wifi disconnects. No connection via cable either. LEDs still blinking on the device. Had to power-cycle the device. This leaves me clueless. Consider using ...

nannou9

Anyone have any wave2 performance numbers between the releases? I was just wondering if the performance is gaining or staying relatively the same. It is not getting any better on audience. On beta 5 I am getting max 550mb with iperf3. I was actually getting ~620 spikes on beta 4 which I cannot repr...

nannou9

kernel panic reboot only after a few hours with beta5

kernel failure in previous boot

Mate your post is useless. You provide no info at all.
Give some model details, post config export etc.

nannou9

No health/temp option in my case too.

nannou9

Has 2.13 been pulled off? It is not finding it for me anymore.
Also as per screenshot it was dated as 1st feb, but there is nothing about 2.13 on MikroTik download page.
Can anybody confirm if this is still available?

nannou9

tested iperf3 throughput wifiwave2 on an audience configured as a simple AP, from blank config - using the 4x4 radio. the other end was an iMac with 3x3 BCM94331CD. max speed topped around 580ish Mbps. this seemed to be strange, so i checked stats. found out that core2 is getting all the fun as sho...

nannou9

R13 & R25 fixed SFP+ access for me but I think the current bug lists are issues associated with config changes that require reboots etc. The frustrating issues is the lack of engagement from Mikrotik telling their customers (beta testers) what's been fixed and what's not and what bugs have been...

nannou9

WHere are the 60hz smartphones Well, talking about that... my friend was testing 5G at his place and came up with some ridiculous number over 600Mbit download... If that really works all around, wifi will be irrelevant in the next decade. This will not happen anytime soon due to cost of contracts a...

nannou9

WHere are the 60hz smartphones Well, talking about that... my friend was testing 5G at his place and came up with some ridiculous number over 600Mbit download... If that really works all around, wifi will be irrelevant in the next decade. This will not happen anytime soon due to cost of contracts a...

nannou9

Sorry nannou you dont know shit. There are stable and dependable wifi5 Access points just as cheap as the capac (TPLINK EAP245) that runs circles around it. In other words, while MT is perfecting WIFI5, that many have done for a number of years with no extra cost or requirement for services. By the...

nannou9

So those complaining that they will not get wifiwave2 because of their device not being capable of it in some way, should buy for example linksys velop which can be very pricey anyway. They are just like MikroTik adding more features all the time- ON SUBSCRIPTION BASIS! Like seriously, paying 4$ a m...

nannou9

For those who are complaining about wifi6 etc, I would encourage you watch few REAL reviews (not sponsored) of some "relatively cheap" wifi 6 routers from big brands (including Ubiquiti) for same price range as MikroTik (~$150) and then run similar benchmarks using MikroTik Audience/RB4011...

nannou9

This is what I am getting too: max 500mb with iperf and it seems to use only half of the cores so might be some temporary beta limitation/bug I hope, which I hope they will fix soon. The main reason why I am using wifiwave2 is because it has much better range and stability for mobile devices. Rest I...

nannou9

Software is already cooking for WiFi6. You can see that in wifiwave2 package.
I bet hardware is in development too.

nannou9

Mate. Read other threads. You should post new one if there is no related one recently, while there are many.

nannou9

In previous betas it was actually completing but after very long time, like 20m. Assuming it is simply still the case.
I have been doing exports myself too and I do not consider this a blocker as others are suggesting.

nannou9

Wifiwave2 frequencies for UK are incomplete. According to Ofcom (UK regulator), frequencies between 5725-5850 MHz do not require DFS and are available for indoor WiFi. Currently they are not available for UK in MikroTik devices. More details: https://www.ofcom.org.uk/consultations-and-statements/cat...

nannou9

However now after less than 1h all my devices disconnect and can’t connect anymore and reboot is needed. There is absolutely nothing in logs which would indicate any problem. Even no unsuccessful authentication or anything. WiFi however is still advertised by the ap, just can’t join. This seems to ...

nannou9

audionce will easily reach 1Gbps traffic in almost any scenario. I don't think there is a problem with the CPU. Test conducted using Traffic Generator. The CPU generating to ip package bit high as they produce 4011. In your 1st post you have mentioned wave2, so I assumed you are using new beta 7.1b...

nannou9

This is same chip as audience. Audience however has 4 chains for it. I can’t get however more than 480mbit data transfer (with 1300mbit link, 3 chains 80mhz) as cpu seems to be limiting factor, where it uses fully 2 cores, while for some funny reason 2 others are unused. Rb4011 ha much better cpu. C...

nannou9

Rc25 fixes all my remaining problems

nannou9

You have clearly not tested ros7 with wifiwave2. The range and performance is amazing. My iPhone used to have unstable 10mbit in my kitchen on AirPort Extreme (last gen). Audience on ros6 was about the same. While with ros7 and wifiwave2 I am getting at the very same place 350mbit stable! Sure ros7 ...

nannou9

Has anybody managed to actually ever save any config change for wifivawe in web ui ? I am getting error saying that exactly one must be set: Mac or master. But I have mac only set through cli, but UI tries to set master each time as there is no disabled/blank option.

nannou9

Audience ros 7.1b4 wifiwave2, factory reset after upgrade to b4 from b3. Tested Wifi3- QCA9984 Wifi reconnection problem is fixed in b4- thanks! However now after less than 1h all my devices disconnect and can’t connect anymore and reboot is needed. There is absolutely nothing in logs which would in...

nannou9

And you need to keep waiting mate.
We have pandemic, so be patient.
For sure they are doing their best.

nannou9

Sorry had no access to my machine and was answering from my mobile previously. Attaching screenshots of my working config on 2.13rc12 eth 1 is my trunk from my router which serves multiple subnets and services for my vlans (DNS, DHCP etc). Sfp+ are my trunks to other switches - so strict and only ta...

nannou9

Why are you forcing vlan id? Also you don’t want to force vlan id 1 as this id is kinda special. I have same switch and got it working well with multiple vlans, trunk ports, access ports etc. My trunk is on sfp+. Vlans are working for me on all 2.13rc5+ There are already threads for css610 vlans whe...

nannou9

After almost two months of testing, 7.1b3 with wave2 only works for one device connected. More devices usually fails to authenticate or are rebooting device. In past somehow I was able to add more devices as long as they were not disconnecting, as later they were unable to reconnect, but since lates...

nannou9

A new testing version 2.13rc12 is available - the VLAN and management connection through SFP+ ports are fixed. Please try upgrading your devices and share your feedback. Below are versions for CSS610-8G-2S+ https://box.mikrotik.com/f/0a98c88515a64596be3d/?dl=1 for CSS610-1Gi-7R-2S+ https://box.mikr...

nannou9

2.13rc12 One more minor issue noticed: MikroTik discovery doesn’t seem to work anymore. Can’t discover devices behind the switch. I am pretty sure this was working previously. Switch itself is discoverable however. My other devices are on trunk port eth1 with poe. Connections however still works if ...

nannou9

2.13rc12 I have new problem now. When I change port name and save I am loosing connection on some ports. It happens every time for me. I need to completely reboot the switch to recover operation. Switching information option off doesn’t change anything. Tested like 5 times and happened each time. Sf...

nannou9

On 2.13rc12 all working for me even with rstp and add information option.
I am using multiple vlans, access ports, trunk ports etc. All good.

nannou9

DHCP client for MikroTik devices doesn’t work for me somehow, have all addresses static on my mix of css610 and crs305.
But it works for devices attached to them- untagged traffic, so does the minimum required.

nannou9

Disabling rstp on sfp port makes the admin working well for me.
Thanks for this workaround.I

nannou9

Accessing admin via sfp on 2.13rc5 usually doesn’t work for me. I gave up on it and I vpn to edge router to access it. Or connect physically to eth ports.

I’ve got my vlans working however.
This thread was helpful viewtopic.php?f=17&t=168532

nannou9

Got it finally working. But tbh not sure why problem with packet loss got suddenly away. Let’s assume user error.

nannou9

I am on 2.13rc5, followed support response steps in one of the first posts. I am getting 96% packet loss with vlans. I can wait anymore, I need vlans. Is there any update from MikroTik please? Any newer rc build? It can’t be any worse for me. I will be forced to order different hardware within days ...

nannou9

There is no "foolproof". By mistake I updated ros7.1beta2 arm to ros7.1beta3 arm64 instead of arm. I got a "brick". Just use netinstall https://wiki.mikrotik.com/wiki/Manual:Netinstall and you should be fine. I managed to brick my device too once when it lost power during upgrad...

nannou9

Posted few findings here viewtopic.php?f=1&t=169992#p836843

nannou9

Mikrotik Audience, bridge mode, UK, updated to 7.1 Beta 3, reset to clean and then setup, purchased 3 days ago from Amazon. I have spent last 3 days testing and ROS 6.X is no go for me as it deliver much worse WIFI than my 7 years old Apple Airports which I am looking to replace. Therefore looking t...

nannou9

Big thanks to Mikrotik!

nannou9

Same problem. Took me few hours of wondering what am I doing wrong before I found this.
Agree. Quite annoying as my networks are connecting to this switch through sfp.

Search found 74 matches