MikroTik

plani

You could reset and have the device run an initial script.

/system reset-configuration run-after-reset=config.rsc

The config.rsc must be stored in the /flash folder. Details can be found here: https://wiki.mikrotik.com/wiki/Manual:C ... tion_Reset

plani

Hi all, I'm unsure where to start the next project step and hope someone can give me an advise or give me a direction. Searching: A mechanism that helps me report/detect/monitor when the failover has been initiated/taken place. Given: A router with WAN-Failover configured, default-WAN goes via ether...

plani

So, I finally found the solution and will post it here for others having the same issue. The solution is that in your capsman configuration you need to set multicast-help=full. Not sure if I can explain why, but finally found the solution on google/stackexchange. /caps-man configuration set multicas...

plani

Still doesn't work. What I did was basically clean up the config by removing the unneeded SSIDs and restarting the APs in order to reprovision as @gotsprings mentioned. My concept is to have 3-4 APs in the end, managed centrally by capsman on the RB3011. Clients connecting to the Wifi will be in VLA...

plani

Yes, same /24 IP-Addressrange and the the same vlan.

plani

@plani: Did you succeed? Sorry @farshield I missed your post. The answer will not be of much help: No, I didn't because I went down another path. As the LTE-modem in my LtAP seemed to be defect, I had a weak moment and bought an SXT-LTE kit which I mounted on my roof. This is then connected to a de...

plani

HI all, I have a running network with VLANs, thanks to this forum. Part of this network are 2 Mikrotik AccessPoints (1x cAP and 1x wAP) managed bei capsman on my central router (RB3011). Assigning WiFi-Clients to VLANs inclulding according DHC-Lease and everything works just fine....at least I thoug...

plani

SOLVED everything.....at least everything relating to this thread. After approx. 2 hours of running various netinstall versions in various orders during different states of the LtAP netboot process I finally have an LtAP mini running RouterOS 6.47.10. And *drums* I have a lte1 interface. *applaus* A...

plani

Additional try: Changing the update-channel to "long-term" which would result in RouterOS Version 6.47.10: Ends in a loop of blinking LEDs in a repeated manner for over 15 minutes.

plani

Unfortunately no other device to test the r11e / mini-PCIe. Regarding the RouterOS version, there was no specific reason for that version I took. BUt what makes it even more strange now is that I tried to update the ROS but it somehow doesn't show anything properly, meaning the Versions presented do...

plani

Hi Sindy, I'm not sure, but I believe I already saw the LTE device last week. So there is a Risk that when I inserted the SIM card for testing today, that I might have fried something, also I believe that is unlikely. So let's hope it is something else. Regarding the ROS version, I upgraded to 6.48 ...

plani

Hi all, after the SIM-card finally arrived I wanted to start to configure my LtAP mini..... and failed. I configured an APN but I have no LTE-Interface anywhere. I unscrewed the LtAP mini and saw that one antenna connector was not connected. Tried with SIM in slot1, slot2 and no sim....no sucess. Ev...

plani

Thanks Sindy for the reply. I've not answered yet, because I was hoping the SIM-Card would arrive for a first test, which is not the case yet. So let me recap in my words what @sindy said to see if I understood correct: a) Setup the LtAP as Router with the LTE "Connecting locally" and rout...

plani

Hi all, after my PoC for a mobile AP using the LTAPmini in a very specific way proved to be a not so good concept, I now want to make use of the little box to: a) increase WiFi coverage in my garden b) use the LTE as the backup/failover to by DSL-based WAN The configuration plan is to create a bridg...

plani

Thank you all for the good feedback. The quick proof of concept showed that although it is doable, it should not be implemented, especially if thought of as a professional, reliable solution. To summarize: - Sharing the Wifi for internal AP and station/client mode will reduce performance noticeable ...

plani

@ConnyMercier: But it did work. Here is the export of the config I User today: /interface bridge add name=bridge1 /interface wireless set [ find default-name=wlan1 ] country=germany \ disabled=no frequency=2422 mode=ap-bridge ssid=\ MobileAP /interface wireless security-profiles set [ find default=y...

plani

Great, thanks for the fast reply. Just two more questions: a) @mkx: You said: "master wireless interface has to be configured as client". Why is that? My logic was, the master-wireless-interface running as AP will 'never fail' while in the meantime the virtual-wireless-interface can try to...

plani

Hi everyone, after finding a few threads that have a similar topic, but none with the configuration I have in mind, I though I'll ask the proven source of truth. I'm looking to implement the following scenario: - A vehicle provides Internet access via LTE while on tour and shares the access to the d...

plani

Adding my experience to the port flapping issue on an RB3011 UiAS: After receiving my RB3011 I updated it by setting it to the stable-branch and going for 6.48. I noticed that the ports on switch2 where randomly going up/down. Connected at that time where ether6 to a Mikrotik CRS as Trunk-Port and e...

plani

Problem solved. I found this or similar issues several times without stating a solution. Maybe because the issue was in front of the keyboard, so here my resolution that might help others: I forgot to put that VLAN on the trunk-port on the switch in the middle. So the client send a request to the DH...

plani

Hi all, I got an issue running a DHCP-Server on my RB3011 and would apreciate an idea where or what to look for. What I have done so far: - Setup is Router RB3011 ---- Switch1 ---- Switch3 ---- Cisco Phone - Set up VLANs according to pcunites tutorial an help as described in my previous thread - VLA...

plani

Thanks tdw, I left out the ingress-filtering for the time being as I wanted to do one step after the other. Regarding the trunkports on switch1 only having tagged 10 and 99 is right too. As the other VLANs (50,70,...) are not yet populated, I just left them out and add them now, as the basics are wo...

plani

It works, a big thank you to @mkx and all others who helped me understand VLANs on RouterOS and get this up and running and to @pcunites HowTo on VLANs for the thorough examples. And for all who stumble over this thread at a later time and wonder what the solution was to my last issue: It's a bit em...

plani

Here the export from switch1, where everything works: # jan/10/2021 20:18:59 by RouterOS 6.48 # # model = CRS326-24G-2S+ /interface bridge add admin-mac=C4:AD:34:E5:2F:D2 auto-mac=no comment=defconf name=bridge \ protocol-mode=none vlan-filtering=yes /interface vlan add interface=bridge name=MGMT_IF...

plani

Here it is the config from switch3: # jan/02/1970 03:25:51 by RouterOS 6.48 # # model = CRS326-24G-2S+ /interface bridge add admin-mac=48:8F:5A:B6:2D:98 auto-mac=no comment=defconf name=bridge \ protocol-mode=none vlan-filtering=yes /interface vlan add interface=bridge name=MGMT_IFACE vlan-id=99 /in...

plani

Hi everyone, Frustration is at a maximum, hope someone can give me a lead where to Look for the following issue: I set up the vlans on all three Switches, as discussed in this thread and pcunites HowTo. Same on the router, setting up a bridge, adding ether6 and the VLAN-Devices for Layer3. After som...

plani

thanks @mkx, I just don't understand Answer c) Maybe there is a misunderstanding. Every VLAN will get it's own /24 IP-Network, So an device plugging in to a "catch-all-VLAN1" will get address from e.g. 192.168.199.0/24, where the actual LAN for example resides in VLAN100 using 192.168.100....

plani

Thanks for the details @mkx Just zu clarify regarding the bridge as interface: Both ways can be used: Define L3 on the bridge, add pvid for desired VLAN on the bridge and add the bridge as untagged member of designated VLAN in /interface bridge vlan Create VLAN-Device by "/interface vlan add in...

plani

Ok, now starting to play around. 1.) First question: I add "/interface bridge vlan add bridge=bridge tagged=ether1,ether10 untagged=ether21,ether22 vlan-ids=100". Then I decide to remove ether10 from that VLAN. So I issue "/interface bridge vlan add bridge=bridge tagged=ether1 untagge...

plani

Great, I'm getting there. Let me summarise: Incoming traffic, called ingress, is configured in "/interface bridge port" and by default behaves as follows: - Incoming traffic that is untagged gets tagged with a VLAN-Id according to the set pvid for that port - Incoming traffic that is alrea...

plani

Thank you for the response, let me try to put it in my words, as I'm not sure if I really got the point: a) Instead of creating a new Bridge, I could use the Bridge from the default config of the CRS326 where all Ports are configured with hw-offloading and pvid=1. I would then need to add VLAN-ID 1 ...

plani

Thanks for the responses, and yes, I went over the tutorial again. Let me ask my question differently: a) Instead of creating a new Bridge, I could use the Bridge from the default config of the CRS326 where all Ports are configured with hw-offloading and pvid=1. I would then need to add VLAN-ID 1 to...

plani

So, as mentioned previously, this approach of configuring multiple bridges on a switch and connecting each bridge with the bridge on another switch is not elegant, to say the least. This is where VLANs come in to play. The logic behind VLANs is simply said: Asociate a specific Port to a virtual LAN ...

plani

So, now let us extend this concept to three switches: But first lets give those coloured networks a name/meaning: GREEN is the usernetwork, or just LAN BLUE is the guest network RED is for now just another separated Network We already know switch1 from the fist post. Switch2 will only have users and...

plani

Hi all together and a happy new year. As I'm levelling up my network, I reached the point everybody here sooner or later digs into: VLAN configuration. After reading the last two weeks here and there, believing to understand the not always so clear documentation and following the tutorial from pcuni...

Search found 35 matches

Re: resetting mikrotik without losing remote access

WAN Failover detection

Re: No client to client connection [SOLVED]

Re: No client to client connection [SOLVED]

Re: No client to client connection [SOLVED]

Re: LTE failover access [SOLVED]

No client to client connection [SOLVED]

Re: r11e-lte dead? [SOLVED]

Re: r11e-lte dead? [SOLVED]

Re: r11e-lte dead? [SOLVED]

Re: r11e-lte dead? [SOLVED]

r11e-lte dead? [SOLVED]

Re: LTE failover access [SOLVED]

LTE failover access [SOLVED]

Re: PoC Mobile AP [SOLVED]

Re: PoC Mobile AP [SOLVED]

Re: PoC Mobile AP [SOLVED]

PoC Mobile AP [SOLVED]

Re: RB3011 port flopping - bad design

Re: DHCP offered, but not bound [SOLVED]

DHCP offered, but not bound [SOLVED]

Re: Basic Understanding Bridge, VLAN, Switch, ... [SOLVED]

Re: Basic Understanding Bridge, VLAN, Switch, ... [SOLVED] [SOLVED]

Re: Basic Understanding Bridge, VLAN, Switch, ... [SOLVED]

Re: Basic Understanding Bridge, VLAN, Switch, ... [SOLVED]

Re: Basic Understanding Bridge, VLAN, Switch, ... [SOLVED]

Re: Basic Understanding Bridge, VLAN, Switch, ... [SOLVED]

Re: Basic Understanding Bridge, VLAN, Switch, ... [SOLVED]

Re: Basic Understanding Bridge, VLAN, Switch, ... [SOLVED]

Re: Basic Understanding Bridge, VLAN, Switch, ... [SOLVED]

Re: Basic Understanding Bridge, VLAN, Switch, ... [SOLVED]

Re: Basic Understanding Bridge, VLAN, Switch, ... [SOLVED]

Re: Basic Understanding Bridge, VLAN, Switch, ... [SOLVED]

Re: Basic Understanding Bridge, VLAN, Switch, ... [SOLVED]

Basic Understanding Bridge, VLAN, Switch, ... [SOLVED]