MikroTik

sealouiw

Sounds like a very reasonable suggestion in case the hEX PoE were my main router, which it currently isn't.

WAN ports ARE NOT on the bridge!!

Yeah, that's what I realized in #3.

/tool mac-server mac-winbox
set allowed-interface-list=none
Change to LAN

I only use Linux.

sealouiw

Wow so the ISP router provides you two private WANIPs one DSL sourced and one LTE sourced but from the same gateway IP? Basically yes. So no public IPs involved here right? Right. Do these come out on different ports on the ISP router I think the policy-based routing decision (which decides which p...

sealouiw

Because pfSense cannot handle having the same gateway IP on both wan interfaces (at least not if automatic failover is desired).

sealouiw

/ LAN1 (DSL) ----------- | Imposed router from ISP | Main router (pfSense) \ LAN2 (LTE) - hEX PoE - | The sole purpose of the hEX PoE connection to the imposed router from the isp is to generate a second gateway ip which is mandatory for proper multi-wan (dsl / lte) in pfSense. LAN1 and LAN2 are in...

sealouiw

Is it possible to use two RGBPOE to inject and extract power from cabling like this:

(inject power via 5.5x2.1mm plug) RGBPOE <---> RGBPOE (extract power via 5.5x2.1mm male-to-male adapter)

sealouiw

Thank you very much, this will definitely help me make my decision.

sealouiw

Actually both, but the sole purpose of the router part is to provide lte fallback: eth1, eth2 (are supposed to act like a router) eth1, eth3, eth4, eth5 (are supposed to act like a managed switch) The above config does exactly what I need, but I'm not really convinced of having found an ideal config...

sealouiw

I recently purchased a hEX PoE and this is the first time I have done any kind of Layer3 configuration on a MikroTik device. It would be great if someone could take a look at my configuration and tell me if I made any obvious mistakes or if you would have done anything differently. [admin@MikroTik] ...

sealouiw

Great, thank you both for your comments!

sealouiw

Does anyone know if any of the recent firmware updates have lowered the idle power consumption of the device, as has been speculated here: viewtopic.php?p=848539#p848516?

sealouiw

I'm about to pull the trigger on a CRS112-8P-4S-IN, but I still have a couple of questions in mind: Would you bet on MikroTik releasing an updated version of this model within the next two years? How much additional power does each S-RJ01 module draw during idle? Is the idle power consumption compar...

sealouiw

@normis, why are you not implementing a proper way to reduce the power output by x dB and why are you not updating the wiki to at least give a hint on how the user is supposed to reduce the power output? The way you handle this topic makes me not want to buy a MikroTik AP ever gain.

sealouiw

I thought I read everything I could find including the relevant wiki pages, but I guess I didn't. Sorry! I did turn off the 'update time' but it made no difference and since the public IP address was displayed even with the DDNS service turned off, I didn't look any further, which was a mistake. Dis...

sealouiw

Settings: [admin@MikroTik] > /ip cloud print ddns-enabled: no ddns-update-interval: none update-time: yes public-address: **.***.**.*** [admin@MikroTik] > /system ntp client print enabled: yes primary-ntp: 192.168.70.1 Firewall log: 10:59:59.733092 IP 192.168.70.10.57860 > 159.148.172.251.15252: UDP...

sealouiw

Does vlan-mode=secure make any different with the above bridge vlan configuration?

sealouiw

Has there been any update on this issue?

Yes:

6.47.8 has resolved our issues and has been error free.

sealouiw

I have updated my configuration - thanks to all who helped me: [admin@MikroTik] > /export hide-sensitive # mar/25/2021 16:18:09 by RouterOS 6.48.1 # software id = AQPZ-DUUH # # model = RouterBOARD D52G-5HacD2HnD-TC # serial number = XXXXXXXXXXXX /interface bridge add ingress-filtering=yes name=bridg...

sealouiw

What kind of idle power consumption can I expect from the RB760iGS?

sealouiw

Yes, but I also wanted to know what kind of problems might arise with my current configuration.

Which problem specifically page number para #?

Take a look at the "VLAN in a bridge with a physical interface" section (the link in my above post should point right at it).

sealouiw

I found the relevant help section that describes exactly why my current configuration is problematic: https://help.mikrotik.com/docs/display/ ... linterface

sealouiw

That would be great! Because I am just falling in love with MikroTik devices.

sealouiw

@Elans

Thank you!

sealouiw

That's quite a lot. Is there no way to reduce the idle power consumption somehow?

sealouiw

After realizing that CSS Switches do not support RouterOS, I am now interested in the power consumption of the CRS112-8G-4S-IN when idle.

sealouiw

I am by no means an expert, so it may well be that I simply don't recognize a mistake. That's why I came here.

PS: I did give the "all interfaces on a single bridge" approach another try, but failed miserably.

sealouiw

Where exactly is the issue with my current configuration? Is it plain wrong or just not elegant? As I said earlier, it does seem to do exactly what I want.

sealouiw

I promise that it will be the last question of this type, but what kind of idle power consumption can I expect from the CSS610-8G-2S+IN?

PS: Please include these numbers in the specifications.

sealouiw

Have a look at the link that anav posted, their you will find all info you need. I'll try my luck once more and report back. also provide a network diagram as it should help figure out what you are trying to accomplish. I simply want the hAP ac2 to act as a managed switch with the management interf...

sealouiw

So you are trying to configure it as switch with 1 trunk port (eth1) and only accessports, correct? Correct, but eth1 is supposed to be a hybrid port. I want the hAP ac2 to be part of the 192.168.30.1/24 subnet. Because it makes no sense to use NAT... The dhcp-server stuff in my config is a leftove...

sealouiw

Instead of using ehter1 I would expect to see the bridge. I use ether1 as hybrid port, which is connected to my firewall. Why are there vlan interfaces here? It does not work without them. Perhaps you can give some information on the purpose for using VLAN's? ether2, ether3, ether4 and ether5 are s...

sealouiw

I recently purchased a hAP ac2 and this is the first time I play with such a product. It would be great if someone could take a look at my configuration and tell me if I made any obvious mistakes or if you would have done anything differently. [admin@MikroTik] > /export hide-sensitive # mar/09/2021 ...

sealouiw

Sorry that I keep asking the same question for different products, but what kind of idle power consumption can I expect from the RB4011iGS+RM?

sealouiw

Thanks! Does anyone know the idle consumption when powered via the 24V DC jack? I guess if anything it would be slightly lower?

Edit: The idle power consumption without WiFi is 3.6 W.

sealouiw

System > Shutdown. But you will need to reconnect AC plug or PoE. Would be great if there was some kind of Wake-on-LAN feature. Or you can disable "most" things on it, like disable WLAN from a scheduler, I tried that, and the lowest power consumption I was able to achieve so far is 3.4 W.

sealouiw

What kind of idle power consumption can I expect from the hAP ac2?

sealouiw

1. I am about to buy a MikroTik RouterBOARD cAP ac and have a question about the LED configuration. I've read that you can turn them off through software, but I've also read that they turn on automatically when you turn the device off and on again. Is it possible to keep the LED configuration on dev...

Search found 36 matches

Re: Double-check my first hEX PoE configuration [SOLVED]

Re: Double-check my first hEX PoE configuration [SOLVED]

Re: Double-check my first hEX PoE configuration [SOLVED]

Re: Double-check my first hEX PoE configuration [SOLVED]

MikroTik RBGPOE - usable as PoE splitter? [SOLVED]

Re: CRS112-8P-4S-IN - To Buy or Not to Buy (in 2021)

Re: Double-check my first hEX PoE configuration [SOLVED]

Double-check my first hEX PoE configuration [SOLVED]

Re: CRS112-8P-4S-IN - To Buy or Not to Buy (in 2021)

Re: RB4011

CRS112-8P-4S-IN - To Buy or Not to Buy (in 2021)

Re: "antenna gain" missing in 6.46.8?

Re: Failed to disable communication with cloud2.mikrotik.com (v6.48.1) [SOLVED]

Failed to prevent communication with cloud2.mikrotik.com [SOLVED]

Re: Double-check my first hAP ac2 configuration

Re: RB4011 Management Lock Ups - where are we now?

Re: Double-check my first hAP ac2 configuration

RB760iGS - idle power consumption

Re: Double-check my first hAP ac2 configuration

Re: Double-check my first hAP ac2 configuration

Re: RB4011iGS+RM - idle power consumption [SOLVED]

Re: CRS112-8G-4S-IN - idle power consumption [SOLVED]

Re: RB4011iGS+RM - idle power consumption [SOLVED]

CRS112-8G-4S-IN - idle power consumption [SOLVED]

Re: Double-check my first hAP ac2 configuration

Re: Double-check my first hAP ac2 configuration

CSS610-8G-2S+IN - idle power consumption [SOLVED]

Re: Double-check my first hAP ac2 configuration

Re: Double-check my first hAP ac2 configuration

Re: Double-check my first hAP ac2 configuration

Double-check my first hAP ac2 configuration

RB4011iGS+RM - idle power consumption [SOLVED]

Re: hAP ac2 - idle power consumption [SOLVED]

Re: cAP ac - a few questions [SOLVED]

hAP ac2 - idle power consumption [SOLVED]

cAP ac - a few questions [SOLVED]