MikroTik

clivejo

If channels are shown during normal operation (LTE modem is registered to network, traffic flows), then they are somehow candidates to be used (either mobility or CA or both). If they only appear while modem is searching for network to connect, then they may be just anything. I'm still wondering wh...

clivejo

Try find them on https://www.cellmapper.net and you will see to which provider belongs.

I have, but it's a rural area and I'm mainly the only contributor of data to CellMapper, to date I have not connected to these bands, so they are not on CellMapper

clivejo

Your B28 has low RSRQs relative to the RSRPs, which means that it receives external interference. Raise a complain to your service provider. I don't even know where these signals are coming from! I have a Pixel 6a running CellMapper and can't seem to get it to record these cells. I've been to the l...

clivejo

Really? the B3 one I have been on for years is :

87 B3 1392 -123 -15.0 -99 1

RSRP : -123
RSRQ : -15
RSSI : -99

I thought B28 would travel a lot better and be more stable?

clivejo

When I run Cell Monitor, I am seeing the following LTE B28 appear: 445 B28 9360 -104 -18.0 -76 2 220 B28 9360 -105 -19.0 -76 2 122 B28 9360 -107 -20.0 -77 9 216 B28 9360 -107 -20.0 -76 2 While I can connect to all the other bands shown (B3 and B20), I can't seem to connect to these bands for some re...

clivejo

Have you tried separating 2.5 and 5GHz networks with separate name (SSIDs)? Then both app device and Tuya IoT device need to be on the same 2.4Ghz network

clivejo

Surely my disk space should be 16 MiB not 15.3 MiB as reported in resources? Is it not being formatted to the correct size, or has some of it been corrupted? Or was it procured from AliExpress, is fake with a rubbish SD card instead?

clivejo

I used on my Chateau Netinstall 7.13 for installation which I described in above post. Only problem I have in general with Netinstall (regardless of version) on Chateau is that I need to hold Reboot button until device appear in Netinstall, it doesn't work by steps described in doc for my device (l...

clivejo

Glad to see you got it working, but to me it is unclear what happened and why new netintall "did not allow" to select more packages :( It allowed me to select them and said it was installing to the router, it said actually said something weird like "Ordering to install", it only...

clivejo

@clivejo You got wrong advice about "The whole reason of buying Mikrotik products was ease of use, this experience is far from it!". I never recommend MT devices (sorry MT) to anyone who has not at least some basic networking knowledge, willing to learn new things and has will to spare so...

clivejo

What a kerfuffle! Tried netinstall via versions 7.13, and 7.12.1 no luck. Found an older netinstall 6.* (can't remember the exact version) and it formatted disk and installed 7.13 system and wifi-qcom-ac packages. Rebooted and imported my config. Seems to be working okay, but really shouldn't have t...

clivejo

I give up, the more I try the worse it gets!

upgrade failed, free 121 kB disk space for a (null)upgrade

clivejo

I've deleted some config trying to make room and its getting worse!

Upgrade failed, free 109 kB disk space for a (null)upgrade

clivejo

Found this in the log - "upgrade failed, free 85 kB disk space for a (null)upgrade"

clivejo

It now won't upgrade to 7.13 from the GUI. It goes through the motions (downloads it, reboots etc) but still remains at 7.12.1

The whole reason of buying Mikrotik products was ease of use, this experience is far from it!

clivejo

No, this device doesn't allow me to select the packages. It just uses one package "routeros" and doesn't let me select what I want (like other devices I have)

clivejo

I've netinstall'ed 7.12.1 and restored the settings from backup so back to where I started.

How do you install it manually?

clivejo

Hi, Yesterday I used the web GUI to update RouterOS from 7.12.1 to 7.13 from stable channel. Before someone jumps on me. Yes, I read the notes and it said that the upgrade procedure would install the necessary wifi packages, but it hasn't. Everything else seems to be working ok, just no wifi (I used...

clivejo

This issue is doing my head in. Now every-time I reboot or have a power cut, the router won't boot. I have to take it down from the roof space and reset the configuration EVERY time now. Once I reset the config and boot into default config, I can restore from backup and everything works fine until t...

clivejo

Hi, Recently my Chateau LTE12 - ROS 7.11.2 (stable) has started to lose my configuration when rebooted. For example, I have a number of static DNS entries which keep being deleted on each reboot. They are definitely being added, as I can use them and it shows " static dns entry added by $user&q...

clivejo

Make sure you netinstall it with v7.3 which just came out. A reboot loop issue has been solved there.

Could you describe the process please? The device is mounted, outside on a mast and it is a big job getting it down to put it in netinstall mode.

clivejo

If you try to upgrade router "in a normal way" (either by hitting the upgrade button or by uploading newer npk files), then there will be something in log to indicate why upgrade failed.

If the device doesn't boot how do I "see" the logs?!

clivejo

on Sunday I cleared the configuration to default and then tried an upgrade via System>Packages, but still won't boot. I have also tried installing v7 via netinstall and that won't work either! People have showed me the RBLHGGR running v7 software, just can't figure out why mine refuses to work!

clivejo

Hi, I have been trying to upgrade my RBLHGGR to ROS v7 but it refuses to boot! I have tried to upgrade via System>Packages and also netinstall but no matter what I try it leaves the device un-bootable. I just spent Sunday afternoon trying to get the device back on-line after trying to install ROS 7....

clivejo

3UK Technical Support are about as useful as an ashtray on a motorbike. The only fix for questions is "turn it off, wait a few seconds and turn it back on again". They have absolutely no understanding of the network or even the current status (They have argued that the network is up and ru...

clivejo

Anyone know when RBLHGGR will be supported? Every-time I have tried to test it, unit fails to boot and have to reset it with v6 software.

clivejo

If I change the band by enabling only B20, I can connect to cell 1720070 which is on the same mast. But I can't connect to both (B3+B20) at the same time!

clivejo

I installed one of your scripts to add these entries into my log, these are the changing value as I was running the command 20+ times. DIAG__LTE6: lte1: rcvd +EEMLTEINTRA: 0, 351, 1392, 36, 0 DIAG__LTE6: lte1: rcvd +EEMLTEINTRA: 0, 9, 1392, 32, 0 DIAG__LTE6: lte1: rcvd +EEMLTEINTRA: 0, 93, 1392, 33,...

clivejo

I use Linux and can't get the information you are looking for. What is the difference between cell id and physical cell? In the cell monitor I am seeing lots of different PHY cell ids appearing on earfcn: 1392 and in the LTE info page can see I'm connected on 99. Cell monitor shows me numbers betwee...

clivejo

/interface lte at-chat 0 input="at+eemginfo\?" output: +EEMLTESVC: 564, 2, 32, 3831, 99, 1392, 19392, 3, 15, 43, 16, 1, 2, 10, 0, 1, 0, 33000, 11, 3237756295, 1720064, 255, 0, 3, 44, 39, 18, 19, 61, 6, 112, 2, 2, 2, 2, 0, 0, 3, 22480, 2, 6, 6, 2, 11, 4, 33774, 10, 2, 83, 0 +EEMLTEINTERRAT:...

clivejo

Still generic story. Remember that math: enB ID * 256 + Sector ID = Current Cell ID eNB ID - ID of your Tower for your ISP (other ISP at the same tower and antennas have other eNB ID) Sector ID - is a ID of sector antenna for specific band, like eg. id 0,1,2,3 can be 4 sides of the world for Band20...

clivejo

I've found some of our local masts incorrectly marked. The one my SXT connects to is correct I think, Google Maps satellite images show two masts at the location, one of which is the one I connect to. My colleague has found the same, he connects to a mast that is not only in the wrong place on Cell...

clivejo

Just an update. I finally found this rogue mast but it turns out that it's location was just an "estimate" based on user submitted signal recordings, so was sending me looking in the wrong direction!! I looked for the bright patches on the coverage checker and drove around in that area whi...

clivejo

I was getting a good speed from the rogue cell and know it's ID, but I can't find it via the MikroTik dish, only B20! The only problem with this cell is that it kept throwing me off any time the local power went off and I couldn't get back onto it, without calling Three and getting them to "res...

clivejo

Sorry my friend, the dish is up on a radio tower! MikroTik_Mast.png It is times like this I regret selling the antenna rotator that used to be on the top of it. I have been out driving with CellMapper today trying to locate the mast's I am connecting to, but can't seem to locate the mast the "r...

clivejo

Oh that is odd!! For B20 it's connecting to a base I know about which is 4.7km away, however for B3 it's connecting to "something" closer with a different eNB, but I can't find it's location. I been trying to collect points with cellmapper, but can't pinpoint it's location :/ The B3 signal...

clivejo

Hi,

Sorry for interrupting on this thread, but I am looking to do the same thing as the OP. As with the OP I can connect to Band 3 or Band 20, but not both at the same time. Has anyone got this to work with Three UK?

Search found 37 matches

Re: Chateau LTE12 - Cell Monitor

Re: Chateau LTE12 - Cell Monitor

Re: Chateau LTE12 - Cell Monitor

Re: Chateau LTE12 - Cell Monitor

Chateau LTE12 - Cell Monitor

Re: Unable to connect Tuya devices

Re: D53G-5HacD2HnD update 7.13 no Wifi

Re: D53G-5HacD2HnD update 7.13 no Wifi

Re: D53G-5HacD2HnD update 7.13 no Wifi

Re: D53G-5HacD2HnD update 7.13 no Wifi

Re: D53G-5HacD2HnD update 7.13 no Wifi

Re: D53G-5HacD2HnD update 7.13 no Wifi

Re: D53G-5HacD2HnD update 7.13 no Wifi

Re: D53G-5HacD2HnD update 7.13 no Wifi

Re: D53G-5HacD2HnD update 7.13 no Wifi

Re: D53G-5HacD2HnD update 7.13 no Wifi

Re: D53G-5HacD2HnD update 7.13 no Wifi

D53G-5HacD2HnD update 7.13 no Wifi

Re: Chateau LTE12 - ROS 7.11.2 (stable) - Loses (some) config on reboot

Chateau LTE12 - ROS 7.11.2 (stable) - Loses (some) config on reboot

Re: Can't upgrade RBLHGGR to ROS7

Re: Can't upgrade RBLHGGR to ROS7

Re: Can't upgrade RBLHGGR to ROS7

Can't upgrade RBLHGGR to ROS7

Re: SXT-LTE6 - Carrier Aggregation - 3UK

Re: v7.1 is released!

Re: SXT-LTE6 - Carrier Aggregation - 3UK

Re: SXT-LTE6 - Carrier Aggregation - 3UK

Re: SXT-LTE6 - Carrier Aggregation - 3UK

Re: SXT-LTE6 - Carrier Aggregation - 3UK

Re: SXT-LTE6 - Carrier Aggregation - 3UK

Re: SXT-LTE6 - Carrier Aggregation - 3UK

Re: SXT-LTE6 - Carrier Aggregation - 3UK

Re: SXT-LTE6 - Carrier Aggregation - 3UK

Re: SXT-LTE6 - Carrier Aggregation - 3UK

Re: SXT-LTE6 - Carrier Aggregation - 3UK

Re: SXT-LTE6 - Carrier Aggregation - 3UK