MikroTik

sseldiablo

http://wiki.mikrotik.com/wiki/Manual:IP ... c_examples

Simply fantastic....
Thx.

sseldiablo

Thanks first of all,
I have a small problem with nat, I have configured a router with public ip rb1000 65.58.XX.XX/24 ether1 on, I use the public ip 65.58.XX.10 to get the ip 192.168.1.20 on ether4, someone could be so kind as to tell me how?
the eth1 and eth2 are not bridges.
Thanks infinitre.

sseldiablo

how did you install it? are you sure it's installed correctly? routerboard: yes model: "600" serial-number: "rebootrebootreboot" current-firmware: "2.19" upgrade-firmware: "2.19" The firmware if 2.19...... and uptime: 4m35s version: "3.19" free-memo...

sseldiablo

try to use the new bios for RB600 which might help you: http://www.routerboard.com/files/rb-2.19/mpc8343-2.19.fwf Hi Uldis, thx fo your response, i have installed this firmware but after one hour the RB rb has restarted, and this happens when there is much load .. you think I might disable some fun...

sseldiablo

If it's got a daughter card on it remove the daughter card and put the mini PCI cards right on the RB600. We have a dozen RB600's, previously had problems with the ones that had daughter boards and 4 cards installed, removed the daughter boards at Uldis's suggestion and no more problems. S Good mor...

sseldiablo

What can I do to charge as little as possible and avoid RB600 making reboot?
since I set the frequency at 266 Mhz seems better but not completely, and given that the problem is dell'overclock, I can do to not load too much rb600, disabling features or maybe more?

Thx to all

sseldiablo

lasted 16 hours, then it is restarted, and I set the frequency at 266 Mhz. Problem is not resolved.

sseldiablo

FACT I HAVE REDUCED THE FREQUENCY OF A 266 MHz CPU AND NOW RB 600 E 'STABLE FOR NOW CAN NOT BRING ANY FAN SHOULD SATISFIED WITH THIS SETUP I hope CHILD DOES NOT RATE AFFECTS THE TRANSFER OF BANDA.

THANK YOU.

sseldiablo

Should reduce the frequency of the processor rb600, because for now I can not change, what are the specific commands and how often I could sect?

Thanks for your reply

sseldiablo

however, I will only say one thing, is not a problem to replace the RB600 here with me I have 20 other location, the problem that this card has happened in a very critical location and difficult access, therefore, what I say attention first to say that the product is ready to be put on the market, b...

sseldiablo

so "/system routerboard print" also shows on the other one Bootloader 2.18?

routerboard: yes
model: "600"
serial-number: "XXXXXXXXXXXX"
current-firmware: "2.18"
upgrade-firmware: "2.18"

this is my system RB

sseldiablo

This morning I checked the uptime of RB and I saw that, a totally enjoyable, it has operated for 6 hours almost 7 if coming 24 hours, pizza for all ...

sseldiablo

This p a very irritating, the RB I tested for a week and I had problems ever since. Now I am with that stupid card hung 30 meters in height and I again every 20 minutes or so, but the fact is that most beautiful coast replace me 500.00 Euro 300 + + for permits rb600 to 150.00. No, I am sorry but fo...

sseldiablo

This p a very irritating, the RB I tested for a week and I had problems ever since. Now I am with that stupid card hung 30 meters in height and I again every 20 minutes or so, but the fact is that most beautiful coast replace me 500.00 Euro 300 + + for permits rb600 to 150.00. No, I am sorry but for...

sseldiablo

Try in this topic

http://forum.mikrotik.com/viewtopic.php?f=3&t=22265

I updated the firmware, we hope to have resolved ... Thank you

sseldiablo

Hi,
i have a problem with a rb 600.
The RB600 is powered at 48 volts but sometimes automatically restarts, and writes:
router was rebooted withut proper shutdown by watchdog timer ....

someone authority may help me?
I do not know what to do, is the only rb that behaves in this way.

Thx to all

sseldiablo

You should disable the watchdog, go Watchdog System menu and uncheck the watchdog timer Thank you very much for your reply. I thought well I to this solution, but if the system goes into block should not restart since the watchdog is disabled. In this case, no risk of having to manually restart the...

sseldiablo

Hi,
i have a problem with a rb 600.
The RB600 is powered at 48 volts but sometimes automatically restarts, and writes:
router was rebooted withut proper shutdown by watchdog timer ....

quancuno authority may help me?
I do not know what to do, is the only rb that behaves in this way.

Thx to all

sseldiablo

thanks for your invaluable advice. Today I moved as far as possible the frequencies and it seems better ... ps the link is now a 14 km distance between the 2 stations. We keep up to date.
Thank you.

sseldiablo

I chose the maximum, rb 600 with 4 R52 H parables dual polarization and have only one result ... Today it is a rainy and foggy day... Only problems .. link and falls back continuously, that ugly thing ...

sseldiablo

try reducing tx power of cards

hi, thx for response,

i have changed a rf card and the situation i best, now have 35/35 mb of throughput.

I noticed that the signal drops more and more worsens the speed, we will see a 14km away with two parables dual feeds 90 cm.

thx to all

sseldiablo

Hi I have installed 2 rb600 dual-mode nstreme but the performances are 16 mb in tx and 21 mb in rx, and values are very unstable. the software of RB are the version 3.13 and 4 rf card used are R52H, accurate that I have set up a test laboratory and 2 stations are 10 metres away. There are things tha...

sseldiablo

the cables are ok, I continue to have the same problem, and say the real thing annoys me, this only with 411, 133C rarely gave this problem.
I do not understand but I am not a few are creating serious problems with the work.

sseldiablo

Hi to all,

first of all sorry for my English.
is possible to upload via telnet a file in a rb411 directory?

thanks for your patience and disponibility.

sseldiablo

This is a problem that I have not ever happened, but there is always a first time. when install the rb411 in some cases, the PC would not the network card and tells me network cable unplugged. This problem is present only in RB411 the rb133C never appear this. 0 ether1 ether 1500 1 R wlan1 wlan 1500...

sseldiablo

Negative... the problem persist....

sseldiablo

hmmm... try enabling ftp-helper in firewall -> service ports, and then in firewall rule use connection state = related

Ok i try it, if is ok i advise you Thx

sseldiablo

Hi to all, i have a big problem to solve, someone could help me? I 2 connectivity ADSL A1 A2, on A1, I want us to spend requested on port 80 443 21 22 110, while the A2 everything else including p2p. I used this rule chain = prerouting protocol = tcp-dst port = 80 src-address-list = Clients action =...

sseldiablo

Hi to all,

i have a RB 600 3.9 routeros, and two ubiquiti xr5 600 mw, are compatible this components?

Thx for all.

sseldiablo

hi to all,

knew I wanted to ask whether a system to limit the number of connections for each user in PPPOE. if I look in firewall, conections I find a high number of connections. Can i limit the number for each client, for example 10 for each client?

Thx

sseldiablo

hi,
i have this message with a new routerboard rb411, any idea?
system,error,critical System rebooted because of kernel failure

sseldiablo

Hi to all.

i have one user connected to my concentrator by RADIUS. Can i redirect tis user to a specific page? for example "www.google.com/welcome.aspx"

Thx to all

sseldiablo

my dafault value, when i make a server PPPoE is 1500, but this is wrogn. i change the value at 1480 and try it. Regards ElDiablo Leave it to its default, PPPoE has 20 bytes overhead that's why it decreases MTU at 1480 bytes. If you have something else configured in your network like tunnels ect or b...

sseldiablo

MTU MRU 1480 because of encapsulation of pppoe
http://www.mikrotik.com/testdocs/ros/2. ... /pppoe.php <- troubleshoting

MTU MRU 1480 at server and client, right?

Thx

sseldiablo

Hi to hall, i have a big network where the clients are connected only with rb133c and only in PPPoE mode. i have a problem with the MRU and MTU parameter, if i set 1500 on pppoe server and 1500 on client, any client do not go in internet or only in any site. My question is, wich is the correct parem...

Search found 35 matches

Re: Nat Problem

Nat Problem

Re: This Stupid RB600 Problem

Re: This Stupid RB600 Problem

Re: This Stupid RB600 Problem

Reboot reboot reboot rb600

Re: This Stupid RB600 Problem

Re: This Stupid RB600 Problem

Re: This Stupid RB600 Problem

Re: This Stupid RB600 Problem

Re: This Stupid RB600 Problem

Re: This Stupid RB600 Problem

Re: This Stupid RB600 Problem

Re: This Stupid RB600 Problem

Re: This Stupid RB600 Problem

This Stupid RB600 Problem

Re: RB600 Problem

RB600 Problem

Re: Nstream Dual RB600 and bad performance.

Re: Nstream Dual RB600 and bad performance.

Re: Nstream Dual RB600 and bad performance.

Nstream Dual RB600 and bad performance.

Re: RB 411 ethernet problem -not link-

RB 133c 411c upload by terminal

RB 411 ethernet problem -not link-

Re: FTP Redirect

Re: FTP Redirect

FTP Redirect

ubiquiti xr5 600 mw and rb600

Limiti number aof connections for Client

RB411

Redirect PPPoE User

Re: MRU MTU

Re: MRU MTU

MRU MTU