On my RBM33G, Wireless module get disabled. I only have WIFI module enabled. My WIFI card is AC so I need wireless module. I tried multiple times to re-enable Wireless module without success. Any idea?

I have a similar issue of getting TCP RST for http connections. Then I discovered it maybe a issue of insufficient power via PoE. My ethernet cable maybe too long and too thin there maybe an issue of powering the device. After I plug the device directly to power and the issue went away.

I have this problem too. It looks like at first try it does register a "trial" license at my mikrotik account. However, it doesn't seem to be recognize the license status as "trail" instead of free. When I try to renew it again, I get bad http response

I am trying to add a IPv6 address block to my Mikrotik router as address-list. I am getting error "Couldn't add new Firewall IPv6 Address list - 2001:250:2000::/27 is not a valid dns name". I am confused with this error. This is a valid IPv6 address block. Why Mikrotik is trying to make it...

There is a few devices that I need to not have IPv6 connectivity. Is there a way to block IPv6 to a few specific devices?

I have similar situations. I find out if I force my modem to LTE I will get IPv4. One thing is interesting, when I am on 5G SA, I do get ipv6 PD to my network. My laptop has no problem accessing Internet, including IPv4 only sites. But my router can't access any sit( when I ask it to check for ROS u...

I tried the forward chain configure you suggested. However, in wireshark I can still see pings coming in from WG2 still trying to go out via other WG tunnel because of that 0.0.0.0/0 via WG1 static route in routing table.

Anyway to make incoming traffic from WG2 back out on WG2?

Oh, these WG1 is not intended for public internet to access the router. But is acted as a WAN for LAN clients. WG2 that has public IP is the one I intended for Internet to access this CHR router.

This CHR does get a public IP via Wireguard Tunnel 2. It also has a local WAN port that goes to the internet. So the WAN port goes to the ISP provided router

YOu have half a diagram. CHR does not typically have any clients SO. a. what is goig to or coming from WG1\ b. what is going to or coming in from WG2| What are the relationships? Are you saying WG1 and WG2 are both WG servers for initial handshake? What is their relationship? Still not clear at all...

I am running CHR at an X86 machine as my home router. So, my CHR has LAN clients. WG1 and WG2 are tunnels going out from my WAN interface. I route all outgoing LAN traffic to WG1 by adding a static route 0.0.0.0/0 & ::/0 via WG1 in the routing table. WG2 I only have a route to that subnet where ...

Here is the network chart https://imgur.com/a/eTy6ehT

I have 2 wireguard tunnels configured on my CHR. 1 wireguard tunnel is used for my primary outgoing traffic. The 2nd Wireguard tunnel has static public IP address. How can I configure my CHR so that when traffic coming in from the 2nd WG Tunnel, the return traffic will go out from the 2nd tunnel? Ri...

I get this error "Error: either "local" is duplicate, or "ip" is a garbage." when CMD is set to ip -6 addr add {myipv6}/64 dev eth0; ip -6 route add default via {ipv6gateay} dev eth0;

Any idea?

How do you resize the partition with CHR? I don't see any tools to do that

Something like this might work for you. { :if ([/ping 8.8.8.8 interval=500ms count=10]<8) do={ :log error "Warning: no internet connection. Reconnecting..."; # Reset WAN interface. e.g. "pppoe-out1" interface /interface/pppoe-client/disable 0 :delay 5s /interface/pppoe-client/en...

This works very well for me:

Code: Select all

:if ([/ping 1.1.1.1 count=6] = 0) do={/ip dhcp-client release [find]}

For [find] do you mean replacing it with like WAN?

Sometimes my WAN would lost DHCP IP. Is there a way to run a Script to release/renew WAN IP when offline?

Oh, I am talking about R11e wifi card. It's not ufl. The spec says mmcx. But when I go to shop for antenna. There are tons of different mmcx.

It's not u.fl. it's way bigger then u.fl

I have trouble figure out exactly what kind of antenna port is on R11e. I am trying to find an internal patch antenna for R11e but always pick the wrong antenna port at (https://www.digikey.com/en/configurator ... a-builder/) Any idea exactly what patch antenna should I look for?

Thanks

Has anyone tried any AX wifi cards that works with RBM33G? Or is there any mikrotik card in the plan?

Thanks

What do you mean by EP mode? How did you switch away from it?

My RB960 is runnong on 7.3.1. However, it doesn't seem like I can reset it or remove any packages from it. I tried reset in the winbox or terminal. It will reboot but not reset to default. I try to press reset button while applying power, it did not react to the reset button pressed. I also try to u...