Why is ethernet 5 UNTAGGED FOR TWO different vlans. ILLEGAL !!! Quite right and an oversight, was fixed asap, regardless it was not in use and thus is not the cause, as i am 'trunked' to a brocade at sfp and using access ports there. All smart devices get ip on Vlan11 ?? How ? You have not set it a...

Well, currently this is for sure a config error as i already dont understand PVID well enough and maybe a mistake in filtering or tagging

hey gurus.., Studied the guides, by anav and others and followed 'thenetworkberg' tutorial to make vlan's on my ros.. Have 1 rb5009, hap ac (backup), and 2 switches.. brocade icx7250/3com baseline 2948 (which will only run on 1g SFP+ Only) My wan side is 5009 connected with 2 bridged mode modems, SO...

Yeah, i did all that turns out, the new mangle ((prerouting/output)) rules (6) seem to be the issue

- Multiple (duplicated) routes deleted - Address gateway was a redaction issue, it was fine before.. so the config is okay (apparently) but routes are shown as USI (unreachable) except for the main table ones.. So why is connectivity lost once we replace 'ether' with the public ip's, i think this is...

post your full config, hiding/redacting whatever you need to

Wait no.. if you want i can pm you the exact public ip's but these are just the dummy ones i enter, these are not correct.. So is our config a 100% ok ? if so why (as in the pdf) it shows all our 'AthenB' and so on as unreachable while they carry the name 'ether' port if i disable and reenable them ...

Hey forum gurus, I'm currently grounded by office seniors since 2 days due to a config issue, and i'm hoping i can get out of my seat can anyone take a look at this, this was done after i consulted and used Anav's knowledge (i can't expect him to be online 24/7) The issue: (which shouldn't be happen...

A quick read would say that you haven't added a route for you fib 'to-wan2' in your routes .. why is that
intentional or mistake ?

Whoa.. Something is wrong here..! i have added the screen shot, i edited it in word and then made a pdf since i couldn't past the screen shot here to show you my routes tab; When i disable a wan to just check if the fail-over was working and the secondary wan kicked in i said fine.., that is until i...

Regarding speed testing our wan’s combined output is shared among the 3 office building’s directors (so like 3 shareholders), and since I truly have a combined wan output of 250m +, I want to be able to show this.. is this possible without config mess ? 2) I saw you have added port forwarding, and i...

Thank you so much man !!!!!!! :D Ive set it up as below (config posted) and its working so far.. but i'm wondering; 1) If some users speed test will they receive the combined speed test result. If not can we make it so that they are able to achieve that result (this is just a requirement and i under...

As per the old approach it was easier, but with your 'monster approach' i dont know how to match the marked connection like isp1-incoming etc etc to all 6 routing tables in mangle (i.e, output chain) and PCC.. Is it possible that i can share you my desk remotely as i have 2 same routers, 1 running t...

(1) Your doing PCC, drop any queueing of WANS for the moment. Ok, but i havent set any que for this, all i did was change Ethernet default, and changed pfifo (2) interface list members...... should be modified to the below /interface list member add interface=ether2-TW list=WAN add interface=ether1-...

Well, its not flux really, but ambitious. Anyhow i tried your approach#1 and did the config, i am now going to change it to your 'monster approach', And i would want to answer some questions you posted also; For PCC MANGLING ENSURE YOU HAVE THE USERS PROPERLY CAPTURED> ( assuming all subnets are VLA...

Ages ago on the forum while i was learning i came upon posts from you and sob and rextended etc.. i found you guys very in-depth with all the mikroitk workings, but after your reply on my post, Damn you really go all the way and look at the config as a whole I had written a few paragraphs actually a...

I require my ISP email for my LAN users to not have a constantly changing gateway/sticky connection (you could say)
Because we get backlisted by the servers firewall as well as banking apps..
Can you take a look at the tread i posted ?
xx Edited xx
i just saw your post on it lol,

Anav, I was under the impression from the forum that; we can have a preferred gateway for traffic to go out to, basically in my PCC setup i can not open emails at a 200mb aggregated system due to config issues I get the error message 'your session has been logged out due to IP address change" a...

Hi guys, General tech enthusiast turned to in-house network guy for my office, dying at the hands of config issues I've got 3 buildings on my Rb5009 on 1Gb Ethernet as well as fiber with Wan1 100Mb / wan2 100Mb / Wan3 50Mb / LTE 25Mb I used PCC load balancing and followed the instruction form Marti...

Hey there, could you also mention how to ensure the gateway doesnt change much And if you have 2 wans, you make 3 PCC rules; 3/0, 3/1,3/2 It will distribute the weight to our assigned WAN's and not cause any issues ? Meaning can we theoretically assign more probability to our system by making more P...