This is the task: Rest the router to default as in Task 1 (this is the last time we reset the router) Create 3 VLANs, with all of them needing to accommodate 253 devices. (use 192.168.0.0/16) have port 2 and 3 in VLAN 1, port 4 in VLAN 2 and keep a VLAN with no assigned port to it. Connect your desk...

Actually, I haven't figured out how to do this yet but ether5 will be used to connect between 2 mikrotik routers and a static route will be setup so that VLANs from router1 can talk to VLANs from router2, however even though I defined the static route it's still not working; the routers can't even p...

Hahaha, thank you so much. They might read this. Hi guys

I see. I clearly am not experienced in VLANs or NAT at all since I didn't know that, but essentially what I was trying to do was that any packet coming from any of these VLANs to the internet shall be masquerated before failing miserably . I am an intern at a company and this task was given to me.

Okay, thank you for your response. I understand that default config is good starting ground but I didn't use it since this is a task and I'm expected to start a new config from scratch.
But I didn't understand what you said about my nat config
Thank you again

I have a Mikrotik router with me. On ether1, I connected my ISP connection line. On ether2, I have my laptop plugged in. ether2 is on vlan40, with its own DHCP and everything. I configured ether1 as DHCP client and added NAT rules, but I still can't access the internet from both the router itself (t...

Yeah this is the best thing to do.

Thank you anyway for bearing with me.

I'm sorry I should have clarified. This is a practice lab, not a real setup. This is just a way to learn how to setup multiple vlans and inter-vlan routing, with each vlan being on its own subnet and having its own dhcp server. The diagram is pretty simple. 2 PCs connected to the router, each on a d...

Yeah my bad. Right now I am using it as a switch even though it is a router also. My entire network is basically just my laptop, the switch and a desktop computer that I try to ping. I am not routing to and from any other interface. I hope that answers your question

i made all the changes and the results are: dhcp_vlan99 works 100% dhcp_vlan20 works 100% dhcp_vlan10 gives out 0.0.0.0 as gateway dhcp_vlan30 is not even found when I run ipconfig /renew I am sorry for being such a pain in the a$$ with these questions and I am trying to configure it as a switch/rou...

Thank you for you response.

Hello All! I have a RB951Ui-2HnD router, on it I have setup vlans 10, 20, 30 and 99. Each vlan has its own DHCP server and running on specific ports. vlan99 on ether1, vlan10 on ether2 and ether3, vlan20 on ether4 and vlan30 on ether5. Everything seems working fine but a few issues: dhcp_vlan10 and ...

Okay thanks guys <3

I lump all the interfaces inside 1 bridge and configure vlan filtering?

Hi, thank you for the reply. I know it's recommended to not use vlan-id=1, but this is a lab not a real setup in which the instructions said to do so. When you say use a single bridge, what do you mean? What to link with the bridge? Thank you for the advices and for the documentation, will go read i...

Hi all, I have a RB951Ui-2HnD router with me, I am using it for a personal lab, not for internet access. I have setup vlan1 on ether2 and ether3, vlan2 on ether4 and vlan3 has no assigned port. ether1 is the port I connected my laptop to in order to configure. I have an ESXi server on ether2. I am t...

Okay, thank you so much <3

Hello all, I am new to Mikrotik and still kinda new to networking in general. I have with me a RB951Ui-2HnD router and I am using it to make a small lab, not as my home router. I connected to it via ether1 but I can't quite figure out how to make ether1 my management port. Is there no such setting o...