As to skip DFS setting: ROS, being the kind which really allows user to fine tune things and doesn't offer too much of "click and forget" functionality, seemingly assumes that if you manually configure frequency list then you "know better" and uses that frequency list despites t...

I create channel 36(5180mhz)-64(5320mhz) and channel 149(5745mhz)-165(5825mhz), one by one. Since you went into trouble of configuring frequencies ... as you found out that some are troublesome, why don't you simply omit those from the list? It doesn't matter if the regulatiobs say it's legal (if i...

VLANS on datapath worked OK on ROS6, but now on ROS7.13 is this such a basic setting which does not exist... why they release such a beta release to users ? Who now have time to mess with "hack" as you call to configure manually VLAN filtering on every CAP device. Datapath works on any ve...

Do you have it configured to use a specific, non- DFS channel? If not, you should. I create channel 36(5180mhz)-64(5320mhz) and channel 149(5745mhz)-165(5825mhz), one by one. These channels and frequencies are all legal in local. I pick up 4 channels with width 20/40/80mhz but channel 48-64 activat...

Hi everyone,

I upgraded routeos to 7.13 and encounter DFS problem in new CAPsMAN. New CAPsMAN persists in doing DFS check at channel 48-64, while old CAPsMAN does not. Setting "all" in Skip DFS channels or/and changing country does not work. How to get rid of DFS? Thhanks.

If they are on the same network, the CAP's should be able to find the CAPsMAN. Have you seen this part: https://help.mikrotik.com/docs/display/ROS/WiFi#WiFi-CAPsMAN-CAPsimpleconfigurationexample: It requires an edit on the default CAPs mode. Or as an alternative, share the config of both CAPsMAN an...

Read the table again Yes, I read it again. My AP runs with routreos + wifi-qcom-ac and is waiting for capsman's control. My switch acts as new capsman with routeros but cannot find AP's wifi interface. Because the table does not mention the switch device but wifi device only, I am not sure whether ...

Correct.

There seems something wrong. I set AP managed by CAPs but CAPs can't find AP's wifi interface. Any advice? Thanks.

Because you are quoting "new capsman ONLY", but video talks about old WiFi5 devices, which in the table is "running two capsmans at the same time" (old + new) In other words, a switch like CRS326-24G-2S+IN that acts as new capsman only just needs routeos 7.13 without package &qu...

The page shows that "New Capsman only controller" needs "routeros" only, while the video "https://www.youtube.com/watch?v=AkBIQxi-VKs" shows that "Package since 7.13" for "CAPsMAN for up to WiFi5 APs" is "routeos+wireless". Which one is cor...

... Mikotik Manual:Fast Path says that FastTrack is FastPath+Connection Tracking. Does it means that FastTrack contains Fast Path？ My interpretation is that without fastpath there is no fasttrack. However I have mixed feelings about the importance of fastpath ... as fastoath manual specifies, there...

Well, if you're running firewall, then fastpath doesn't make much sense (if I understand its function correctly, it's a shortcut between different drivers and traffic then bypasses some of generic L2 of ROS and all of L3, for firewalling such shortcuts should not happen). Fasttract is (again accord...

One likely culprit, you have to disable/remove all firewall rules. https://wiki.mikrotik.com/wiki/Manual:Fast_Path Does it mean that I can only pick up one feature between Fast Track and Fast Path? I added "/ip firewall filter add chain=forward action=fasttrack-connection connection-state=esta...

Hi all,

I noticed that IPv4 Fast Path somehow is not activated but Allow Fast Path is checked in IP Settings. Where is the root cause most possibly? Thanks.

Hi all, I want my WiFi network to run on pure 5G frequency band and turn off 2.4G signal. While I can disable 2.4G wireless interface on winbox, the 2.4G signal still keeps transmitting and it is showing a "hidden network" in spectrum software. Is there way to turn off 2.4G or any WiFi sig...

Unfortunately, 7.11.2 has been reported causing issues on netinstall for quite some users here. Normal operation should be fine though, it's just something with netinstall that seems to be 'off'. Not only netinstall but also RouteOS. I clicked "Provision" and "Upgrade" in "...

My situation is similar to yours. I have 2 wAp ac wireless APs and I set them as managed by CAPsMAN. ... What exactly is your device model? I ask because when I was looking for a solution to my problem, I found information that in some devices, to reset, you need to short-circuit special contacts o...

Finally, the issue got resolved. The last stable version (7.11.2) of netinstall failed to find wAp ac, while the last Beta version (7.12beta9) successfully found and rewrote RouteOS. 7.11.2 stable probably may not work properly on some products, at least including wAP ac. wAP ac should avoid upgradi...

My situation is similar to yours. I have 2 wAp ac wireless APs and I set them as managed by CAPsMAN. In the beginning they work properly, after several hours they 2 all suddenly POWER-OFF and no longer get connected to ethernet. I hold the reset button for 15 seconds to carry out netinstall and expe...

Hi all, I have 2 wAp ac wireless APs and I set them as managed by CAPsMAN. In the beginning they work properly, after several hours they 2 all suddenly POWER-OFF and no longer get connected to ethernet. I hold the reset button for 15 seconds to carry out netinstall and expect them to get reconnected...