Hello, We have customers using wireless RB4011 routers and we want to further extend wireless coverage throughout their building. Of course, we have customers using other Mikrotik's as their "main" router as well. So, what is the best way to connect the RB4011 wirelessly to an Audience tha...
this is SO BADLY NEEDED - keep it simple. Why does Mikrotik continue to lose router sales for us, when nearly every $ 100+ router from Best buy has dual-band?
I truly think TR-069 would be one of the best things Mikrotik has ever done. The "inside of the house" is becoming a big challenge for ISPs. We have even small families having 15+ devices inside their home. It could be a BIG help and profit to ISPs to be able to effectively manage that. I ...
To follow up on our situation - I was the original poster. I had upset customers - this was a MDU - 6 customers affected, I had to upgrade to an 493AH (from the 493) and solve the problem. I had tried to re-setup the 493 router from scratch - adding bits and pieces at a time, and it would sometimes ...
We updated a 433 and a 493 (both non-AH versions). Both of them are doing NAT (src-nat) and both having the same problem. Everything looks 100%, the router can talk through the Internet and the customers (NATd) can talk to the router, but cannot talk through it. Both of these routers were on 4.1.7, ...
I have started using MasterPort instead of bridging, hoping to improve my performance a little bit, as I dont need all the benefits of bridging offered. I keep things very simple... WAN port (sometimes two or more using MasterPort configurations) , and "LAN" Ports (using MasterPort configu...
Hello. From my main tower, I have 8 different towers to feed in the 5Ghz range. We use 5.275 to 5.325 at our towers and 2.4, so I have the 5.4upper to 5.8 to use for BHs and there are a couple other carriers in the area, so I have to be very efficient. I of course, use different polarities where I c...
OK... the router is really in a pretty simple disposition... no mangle rules.. no NAT... I have some simple (standard on all are Tiks) FW rules but they are disabled at the moment. Also, individual queues for each customer for BW control.... again disabled. I have even removed completely both queue...
I have two towers that have the same symptom. One of them did it from the moment I put the Tik in, and the other started recently (I think) One running 3.9 the other 3.10. The symptom is… when I ping an even numbered IP address that is on the router block (“lan”) side of the Tik, from an even number...
1 link using rb333 or rb450 and r52 wireless cards will get you cumulitive of 54megabits using a 40mhz band. eric Eric, I finally got a chance to try this today. Two 433 boards each with one R52 card. connected indoors. Tried the basic way I know how to connect these. AP Bridge and WDS Slave. in 40...
I use DHCP relay to get packets back a central server that hands out Static IPs. Have used this in one form or another for many years. I found a situation where the packets never make it back to the server at all and need to be able to troubleshoot it, and find where it breaks I have Central NOC, To...
What I discovered was not to use Port 1 for anything other than POE on the RB450 There is something different about that port that in two different tower uses, is limiting BW. Heres the scenario. My towers are generally low BW use (always less than 10Mbit). If i am feeding Tower A, and there is a To...
I just put in an RB450 at a moderate use tower and have major throughput problems. 1) This tower is BH’d to my office on Tranzeo 5a series that gives BW of 13 to 14MB (up or down) when I plug in direct. 2) I have the BH in Port 2, and Ports 2, 3, 4 are bridged (ports 3 and 4 have other PTP Tranzeo’s...
I have an application to feed three small POP towers from one large one. I wanted to use 3 XR5 cards in a single routerboard, but have some concerns. Heat - I am in Florida so am concerned about "spreading things out" with room to breath. I also have to feed this the entire way electricall...
Been watching some discussions about various bonding or other techniques to get some pretty decent backhauls created. I want to start on a really short link. <1 mile I am looking specific suggestions for this could with a hardware list to put it together right away. Dont know if it matters but will ...
Hi, I have been steadily been rolling out 'Tiks with routed blocks of IPs to all our wireless towers, and now am ready for two things. 1) Make all towers have redundant links to at least one other tower and setup the appropriate protocols for that. 2) Replace our "distribution router", a C...
I hope this doesn't have people laughing on the floor. I have not used Mtik for Wireless networking before, and I want to create a very simple bridge between two buildings. Using XR9 cards. On the AP, I Bridged Ether1 and Wlan1 together (RB 433). I set the Wlan to be AP of course, picked freq., SID,...
We used the RB192 in multi-tennant office buildings, serving internet to many offices each with its own firewalled private subnet and NATd to Static (Routable Internet) IPs. They pass about 12+ Mbit to a client which is more than sufficient, seing the radio feeding it only does 10Mbit. Works great.....
Based on the drawing above.... Interesting.. but the question then becomes... (and this depends into the combination of how wide your network is vs. how deep as well) ... is the design philosophy to immediately serve the need to the customer in the most efficient (except looking at the next router i...
I am interested in implementing OpenDNS for some of my business customers that need content filtering. (when a users PC is pointed at OpenDNS server, “the filtering works”. If the customer puts a dif. DNS server in his PC locally, then he can bypass it) BUT, If I force said business customer to use ...
Since there is no official web page for the process of new products coming out, and EOL timelines, etc., all we can do is speculate on things based on what distributors guestimates are. Soooo... IS the RB192 now EOL? Is there a RB492 coming out to replace it, ala the rest of the lines. We really nee...
I tried looking in the PDF but cant find an answer. I googled around, but no answer to my question in general terms I tried this on two Mtiks - one runnig 3.3 and one on 3.4. they are at two of my wireless towers. When pinging a device (such as an AP or an SM) with a regular ping, I get the expect s...
Hi, I have been playing with the NAT function and dont quite have a handle on it. The overall scenario is this. I want to use this router to feed 3 customers in the same building, each with its own NATd subnet (192.168.1, 192.168.2, 192.168.3). Since each customer is to have their own public IP, I w...
I have used this script (minus the three burst "variables") for a while successfully. When I add the three burst items, the script doesnt run. It does nothing, as though there is an error in it. I pasted the same "effectual" string into a terminal window and it works fine. I am ...