Just avoid port ether1 that usually set as WAN in default config. All the other stuff should work without any issue.

@mozerd amazing support here ! I will try as soon as I m on side. Look like easy, as usually when you know how

Maybe it is time to post the export of the configuration?

I m a couple of day away ... I will then do it. It is a little bit more that just ipv6 there. Dual WAN, VLAN segregated, one routing over rb5900 (starlink) and one over opnsense. Multiple other remote subnet over wireguard .

I probably give up with the ipv6 mikrotik dhcpserver. Local link IP are distributed / advertised but dhcp seem to not like my setup. I got two VLAN1 one where an dhcpd server work from another server (opnsense) and the one (VLAN2) where I should get the mikrotik dhcp server run. It just don't ... ma...

I hazily remember I had to reboot the router after assigning the global address to the LAN interface in order that SLAAC would start working hmm, ok - i will then try all the stuff on another lab router, before i broke something. Reboot after each change is not really nice :) 2) normal LAN hosts ha...

Kudos to @sindy, great support. I got the pinging working, with adding default route to fe80::200:5eff:fe00:101 link local, that is for me a little bit magic. Is this something specific to starlink router that always use this ip or is general in ipv6. Now i m struggling with the setting of clients i...

hmm, i didn't get it. Let's try to explain my plan with a pic (attached). I have my prefix 2a0d:3344:1234:ab00::/56 . on the wan of the router. Now I would like to redistribute with a dhcpserver on my router in the LAN a subnet 2a0d:3344:1234:ab01::/64 . I have now two issue. Would be nice to ping t...

Hi, thanks for the good advices here, i got the prefix from my starlink - issue is firewall rule by default limit the port udp/546 from fe80::/10, that block the incoming add.

Now i m struggling with dhcpdIPv6 setup. Where is RA in routerOS ?

You don't need NAT with ipv6 , you normally get a /64 or /52 prefix that is enough for all your connected devices.

Submitted SUP-177913

Ok, i will do it ... at the moment the switch is working but fully broken, no reboot possible, unistall of package is not possible anymore. I m too lazy (and not on site) to netinstall it... will solve the problem but :( -- so now more the capsman and then provide ticket. I m lucky this switch ist n...

ok, is strange, because same config on other CRS326-24G-2S+ with same config still have space left. Is disk a special part of memory, or could be possible to shrint memory and expand disk ? CAPsMAN is absolutly indifferent where is installed ... traffic is not routing there. Let's move it to RB5009U...

Hi, after installin 7.17 my disk got space 0. How to clean it up ? What i have done wrong ? I have on this switch CAPsMAN (old and new), is this the issue, should i move somewhere else ? admin@switch012] > /system/resource print uptime: 39m18s version: 7.17 (stable) build-time: 2025-01-16 08:19:28 f...

At least on 7.17, the card honors what you ask it to advertise as part of auto negotiation. If you are getting no link when pairing with a 10G device, remove the 25G options from what the interface on the CCR2004-1G-2XS-PCIe advertises and it will link. I m running now 7.16.2 and i still not reboot...

Hi, how did you setup the card ? is in standard config as in https://cdn.mikrotik.com/web-assets/rb_images/2155_m.png ? Did you let card bootup before you ubuntu bootet, try to restart networking services. i have it running on debian and it use driver atl1c ethtool -i ensfp1 driver: atl1c version: 6...

On device like SXT LTE6 kit would be a very good improvement. I run i some trouble of SIM not surviving extreme winter/summer temperature and humidity.

I have only experience with linux, but I would try a reset and a new netinstall.
Try to be patient and see the result of netinstall.
Card should be then come up again in the default configuration, sfp1 and 2 in passthrough mode and ether1/2 in Bridge mode as admin.

Hi,
There is some roadmap, plan for support of eSIM ?
For SXT LTE would be a very nice improvement, I already experienced issues with the physical SIM, some are very difficult to operate in extreme weather ... and such antennas are most of the time in places that are not so easily reachable.

I have installed version 7.15.3 and on sfp2 I didn't manage to get link up. It say all time, no link. I connect it to a CSR305 with a module and cable. This side say link ok, cable of and I got RX, CCR2004 side say no link and no communication. There is outthere somody managed to get it running, bot...

I had the same issue after upgrading to v7.14. I had to use Netinstall and the reset switch on the card to downgrade back to 7.13.5 to get stability back under Proxmox. How did you put the card in netinstall mode ? Really have to open the server and press the non existent reset button, with screwdr...

i have 7.14 installed and boot only without sfp modules.
I tried to install the new 7.14.1, no luck, get stuck, fan getting crazy. Is really a disaster at the moment. Got two of this card and both broken ...
Log say

"kernel failure in previous boot"