MikroTik

DieselPower

Hi all. I am attempting to install a Quectal EM20-G in a SXT LTE KIT US. I have used an EM12-G without issues in the past, but the EM20 just won't cooperate. I have tried setting up a ppp interface to USB1 but I still cannot send AT commands, I'm assuming because it's not automatically detected as a...

DieselPower

I let this sit in hopes it would be cleared up with another update, but...

Is there anyone that could look at this? I have 50 routers and typing the ip each time sucks! Normis, I could send you a copy of crossover for you to test it with? Just let me know.

DieselPower

I don't know how much demand there would be for this sort of thing, but this is what I wish for the most on the RB. 1) Power supply voltage reporting in system/health on all models Reason: I have a lot of solar powered RB out there, and monitoring battery level with The Dude would be just awesome! 2...

DieselPower

I would also like to know if this is possible.

DieselPower

Yes, all antennas and pigtails have been replaced. We might say the original was hard to recognize! Good idea on the airview, I'll get one on the way. I do not use lightning suppression because of signal loss, been there done that... There is a pager system running at 200 something MHz on one tower,...

DieselPower

I have a 6 mile link that used to work perfectly. It has the complete Fresnel zone open, so no LOS issues here. We had a storm that took out one tower completely a few months ago and I have been fighting it ever since. ALL equipment on both ends has been replaced at least twice and without change to...

DieselPower

So it may have something to do with my latest upgrade of Crossover Office, I'll have to check that out

DieselPower

Winbox has recently changed the way it loads addresses into the "connect to" field for some reason. I used to be able to specifically click on the routers IP address in the search box. Now, no matter where I click, it populates the "connect to" with the mac address, and if I need...

DieselPower

To work around this problem I have always invoked "dhclient eth0" and let it give up, then the ... button will work. Also I didn't have this problem until KDE4 came out, I have no idea what that would have to do with it, but I does make a difference??? I actually ran KDE3 for a long time o...

DieselPower

OK, It seemes like it could be my provider. I'm really stumped. I have a linux server DIRECTLY connected to the DSL line and it does exactly the same thing. How should I approach my provider about this? What should I tell them? I usually get someone that says "Oh, your modem is up just fine, ca...

DieselPower

I get very slow responses on my network at times, and ping acts very strangely. It seems very random, and usually lasts no longer than 10 minutes. What could cause this? Ping to my gateway router (10.0.0.1) works perfectly all the time. Is this likely to be my upstream provider? Just for info, Iv'e ...

DieselPower

Thanks, I didn't see that!

DieselPower

Can anyone help me codger up a way to add a firewall rule that blocks an IP address after say 25 failed logins, and then removes it after 24 hours?

DieselPower

@melwong Yup, waaay to easy! I got my whole network reconfigured last night, and only had one unhappy customer when I got up this morning. Had to refresh his DHCP supplied routing tables. Not too bad! @Chupaka Thanks, so I should probably go with a class A just for future proof-ness, not like there'...

DieselPower

Wow, RIP is way too easy! Problem is, I want to use OSPF, and I don't fully understand it yet... More heavy reading. My biggest problem is I'm learning on a live network so I don't touch anything until I KNOW what the results will be, and that level of confidence only comes with LOTS of examples and...

DieselPower

My network is getting complicated VERY fast. Currently it is bridged, and I am running out of IP addresses with just a class C. In about 10 days I will be adding another AP that will double the size of my network in just a matter of weeks. Some serious planning needs to be done here, and I am asking...

DieselPower

Wow, I just found this. Its going in my toolbox for sure! I tested it on v4.0 beta and it works there too. Thanks!

DieselPower

Hi Guys, I've done a lot of reading on this, but none of the setups seemed to have anything to do with mine, so I have a couple of questions. I am wanting to prioritize Voip traffic so that customers don't get choppy voice while downloading. Right now I only have 4 customers using voip, and I know 3...

DieselPower

I am having problems with snmp on all versions of routeros from 2.7 to 3.0. I get a response to this quary for routes. root@lawrence:/home/lawrence# snmpwalk -v1 -c public 10.0.0.1 1.3.6.1.2.1.4.24.3.0 But not to this one for tx-rate. root@lawrence:/home/lawrence# snmpwalk -v1 -c public 10.0.0.1 .1....

DieselPower

I am having the same problem. This works, (routes) snmpwalk -v1 -c public 69.131.249.115 1.3.6.1.2.1.4.24.3.0 Nothing under /interface/wireless works. This returns nothing. (tx rate) snmpwalk -v1 -c public 69.131.249.115 .1.3.6.1.4.1.14988.1.1.1.1.1.2.2 (yes, you are welcome to try at the IP address...

DieselPower

OK, The first router just started acting up again, I was having to reboot it every 30 seconds before it would just stop passing traffic on the ether1 interface. I just downgraded to 3.13 on that router and I will watch carefully to see if it holds up now.

Anyone with any info, please respond...

DieselPower

OK, after another router going crazy this morning, I have found that the IPv6 package was causing the problem. Again, I'm running RoS V3.16. This router just stopped passing any packets on the wlan interface, and when I logged in from the ether side, all the interfaces were appearing and disapearing...

DieselPower

Hi Guys, I just upgraded ROS to 3.16 on all my 411's as part of my deployment of IPv6, I'm not sure this has anything to do with my problem though. I have one router with [ether1]-[bridge]-[ap-bridge/wds] that decided to act up today. I could not even mac-ping anything connected to the wlan interfac...

DieselPower

If you're being overwhelmed by off-band emissions, an amp is only going to add to the problem. I'm at a radio station site and I have no problems with off-band emissions, but I don't use your gear. How many watts is the station putting out? And is it an old tube xmitter they're running? The station...

DieselPower

Safe-mode to the rescue here :D In the manuel, it says WDS for Nstreme protocol requires using station-wds mode on one of the peers. Configurations with WDS between AP modes (bridge and ap-bridge) will not work. So will this work with Nstream on all links? Tower-AP --------------- Repeater ---------...

DieselPower

It looks like WDS-Slave is what I want on my AP's? I'm just double checking because climbing 400 feet with a laptop and serial cable is not an option I like to think about...

DieselPower

OK, I see ap-bridge + WDS is not compatible with Nstream, I'll have to do some reading on what to do with that...

DieselPower

What about trying Nstream on the 2.4 link? I don't fully understand Nstream, maybe it would also be good on the 900 network as well. Is it just a matter of enabling it on all routers and everything will reconnect? No extra bridging or other settings that may catch me by surprise and send me scurryin...

DieselPower

Exactly the same.

DieselPower

I know, but it's kinda laughable when you're right next to a 100KW FM station. Their off-band emissions are quite a lot more that 5w!

Any ideas on my BW problem?

DieselPower

TN.

I'm going to add the image again because one of my servers is off line for maintenance.

DieselPower

I just changed a few things in my wireless setup to try to minimize noise interference. Mainly move my XR2 and XR9 cards to separate boards with RF shielding between them. My throughput went way down, like from 4.5Mb/s to 280Kb/s. Is their anything that just stands out as to why that might be? http:...

DieselPower

Hi guys, I have a fairly large wireless network using RB411's and XR9 cards. A customer just requested a public static IP. I have several available, but how do I forward it to their router? You can see my network structure in the image below. Both IP's are available on the same port of the DSL modem...

DieselPower

Thanks, that worked. Just had to change the interface for my purposes. Sometimes I think if it was plain linux I could get things done a lot faster than these GUI systems! Anyway, a great system doing exactly what I need.

Thanks,

Lawrence

DieselPower

I am just trying out RouterOS for the first time on a CPE (rb133c). I have a 900Mhz wireless system mostly running on pfSense. I got rOS to connect and get DHCP address on the WAN, and it is giving DHCP offers on the LAN. I have no firewall rules. So what's happening is I get the client configured t...

Search found 35 matches

Trouble with EM20-G not showing up in interfaces

Re: Winbox problems...

Possible Feature Request

Re: Passwordless ssh login

Re: Poor thruoughput & lost packets using XR9 with excelent SNR

Poor thruoughput & lost packets using XR9 with excelent SNR

Re: Winbox problems...

Winbox problems...

Re: winbox won't connect using the mac address.

Re: very strange ping, lost packets -routing mixup?

very strange ping, lost packets -routing mixup?

Re: Gazillions of failed logins, and how to auto-block

Gazillions of failed logins, and how to auto-block

Re: Network Planning/Routing Help

Re: Network Planning/Routing Help

Network Planning/Routing Help

Re: Yet Another wireless alignment script with LEDs and beeps

Voip Prioritizing with Usermanager Rate Limit

snmp problems

Re: snmp frequency gathering

Re: WDS Bridge Problem

Re: WDS Bridge Problem

WDS Bridge Problem

Re: Bandwidth problems.

Re: Bandwidth problems.

Re: Bandwidth problems.

Re: Bandwidth problems.

Re: Bandwidth problems.

Re: Bandwidth problems.

Re: Bandwidth problems.

Re: Bandwidth problems.

Bandwidth problems.

Forwarding static IP over natted network.

Re: Need help with NAT (I think)

Need help with NAT (I think)