Well, I realized that the Vlan setup wasnt going to work had equipment that didn't support the option for a Vlan, So I had to go back to the basics then I went through the first time setup. It has not been completly customized yet but here it is. If I did something wrong let me know. # /interface br...

No I’m not trying to make a default config, I was just trying to use what was there from the default configuration and change it to what I wanted, I’m still struggling with the how the microtok router has a wan configuration and a lan configuration, with most routers when you aren’t connected to the...

I used the default config as a basis, what i didn't understand was the mgnt line from the vlan setup. Let me now if theres anything wrong with it! #------------------------------------------------------------------------------- :if ($action = "apply") do={ # wait for interfaces :local coun...

I haven’t edited the config yet for the router still at the default state. I have only added a password for the Wi-Fiso far, but this is what the network looks like right now and what I want to make it look like!

So with this router being a secondary router, I don’t need the router setup for the wisp option correct and just doing a basic ap router should be fine correct? And then because I’m going to be using a vlan I just need to configure the vlan that’s coming from the switch correct? Because every router...

So I’m having trouble understanding that with the default configuration that it uses wan, so would be the difference of connecting the cable directly to the wan port versus eth1. I do understand that usually you only use the wan port when ur connecting to a modem that doesn’t have router capabilitie...

So i reset the config, i was able to login with the 192.168.88.1 and still not with winbox using the mac on the bottom side of the router, when i logged in i realized that it wasnt connecting because the mac address was not the same but one number off! so the software upgraded sucessfully was able t...

yes the cable was connected to port 4 that im using and then i connected it to port 2, then tried port 6. the wifi has internet but it wont connect with the mac adress using winbox, or by setting up a static ip on the lan connection also setting up the wifi with a static ip and trying to go to the 1...

i added the wlan to the bridge to see it in the config and forgot to remove it and i added the 6.49.13 file and rebooted, but now i cannot even connect with winbox using the mac address.

So find the firmware 6.49.13 upload to files and do i just click on it and let it install or waht process do i go through?

no its the config that was exported that's what i downloaded, but how do i reimport the config when its been edited?

well right now its currently the main router, I'm hoping to setup a mutiwan router with a vlan that would pass through the current network to all devices!

Can it do both be a dumb switch and have the wifi work at the same time as well?

So I was told to use the command do /export file=config but apparently it changed from 6.32.3 to later because I used export file=config and it appered in files. # jun/12/2024 19:51:01 by RouterOS 6.37.3 # /interface bridge add name=bridge1 /interface wireless set [ find default-name=wlan1 ] disable...

The RB2011UiAS-2HnD-IN was already installed never used the mikrotik os before, I read the documentation that said to use Winbox to connect using the mac address. i was able to connect and seenthe software was out dated and that the time and date was off, so i corrected the time and date and was goi...

ill create a thread in the beginer basics. thank you!

yeah I did that do "/export file=config", with and without the quotes but nothing shows up! For some reason i dont think its going to the right directory! Im using winbox terminal!

I did the do command but it isnt showing in files, how do i list the files and directories and move within them?

So there is no chart that details the mikrotik devices model numbers and the current software compatible with or which version you should use for the device? It was a good thing you mention about upgrading to 7.12.1, the device that im working with is a RB2011UiAS-2HnD-IN using not by my choice 6.37...

well thats great when it works.... but that only answers if i want to auto update... it doesn't answer my other questions!

We made a table with some clarifications, can you guys let me know if this clears up some confusion? I see that Documentation and YouTube video still leaves some questions unanswered. So let's try it like this: Sorry I'm very new forgive me if this chart explains it, but if i go to the suppot &...