I'm using SXT N and 20Mhz of bandwidth.

Hello

What is the highest concurrent data traffic allowed in practice in NV2 (mimo2x2) ?

thanks,

Tecnoarte

So I want to deliver a DHCP Server IP from CCR for each VLAN in the RB2011. I have only one DHCP

Yes, the client obtains the IP through CCR PPPoE Server.

Hello, I have a CCR1009 with DHCP and PPPoE functioning properly, but need to connect a RB2011 where I will have client1 (vlan10), client2 (vlan20) and client3 (VLAN30). In the RB2011 created the DHCP-Client in Port1 and PPPoE-Client in Vlan 10, 20 and 30. I made the following configuration, but it ...

But I would like to replace the original power supply VAC to VDC, it´s possible? I don´t like to use POE.

Can I replace the original source of CCR1009-8G-1S-1S + by a source of 48V DC ?

Alexandre

Hello,

I would like to configure the ports 6 to 10 of RB2011 each for a client through VPN, port 1 is the internet output, this port is in Bridge with a panel. How would a basic configuration using VPN?

Thanks,

Alexandre

Hello,

What is the practical rates of MIMO 2x2 802.11n ?

Hello,

I run the script to enable the rates:

/interface wireless set supported-rates-a/g=24Mbps,36Mbps,48Mbps,54Mbps

Which the command to disable ?

Thank you !

Hello,

How to export the LastIP from Registration Wireless-Table ?

Alexandre

Ok, but I think the problem is when you disconnect, the following message appears in the log "Disconnected, management-protection failure". Now, for example, all customers disconnected and log "Disconnected, request to disconnected from registration table".

Hello,

Use 802.11n with WPA2-PSK authentication (AES), even with great signal, some customers disconnect and connect frequently and the log shows "Connected, wants bridge." What could be happening?

Alexandre

We have two RB922 in our tower, one with 40 and another with 25 clients running on NV2, however, we noted that both restart occasionally logging the message: "System, error, critical system rebooted because of failure kernel" "System, error, critical router was rebooted without proper...

Hello,

Already we disabled the Dude and SNMP of RBs to see if the problem was, but it keeps happening. We have sent the file to the support, but, all alternatives that still did not get resolved

Alexandre

Hello, We have two rb922 connected in a rb260 and we have problem in these two rb922, often they restart and log displays the message "System rebooted because of kernel failure". Already upgraded to version 6.35.4, update the firmware to 3:33, connect the original power supply, however, th...

Perfect Sam, the error was in the name of the interface !!! Now is working perfectly...

Thanks for the support Sam and Hilton

Alexandre

Hilton, thanks for the script, but for me it did not work in version 4.10 !

Sam, anything new ?

thanks...

Alexandre

After upgrading to RouterOS 4.10, DDNS ChangeIP my script stopped working ... follow the guidelines of http://wiki.mikrotik.com/wiki/Dynamic_D ... angeIP.com site, but did not work! Has anyone experienced this problem?

Alexandre

Ok, thanks for all the details !!!

I have the ZTE MF626 USB modem, I could use it in USB port without the SIM and add the SIM slot onboard ?

Okay, now I understand it, could send me a link to where I can find the Mini PCI-E compatible?

Tanks,

Alexandre

Ok, the RB411U have Mini-PCI Slot, Mini PCI-e, and also has onboard SIM Card.

I see that there are three ways to use 3G ... by USB, by Mini PCI-e our slot onboard SIM Card. I would like to use the latter to setup 3G.

Tanks

Yes, but I would like to use the chip 3G directly in the slot onboard the RB411U, I would not want to use the modem in usb port.

Tanks.

How to configure the 3G SIM card directly into the onboard slot RB411U ?

When I connect the sim card, the RB does not recognize any additional port !!!

To configure the onboard SIM card I need to leave the modem plugged into the USB port ?

The version of RouterOS is 3.28

Tanks.

My english is bad !!! sorry...
He would like that the client received the information from cache in the speed of its throughput (6199kbps) on the contrary of the speed established in your simple queue (128kbps).

tanks

I have cache full in door 3128 configured with rules in mangles and simple queue unlimited, however, when activating this simple queue, all the clients to pass through with unlimited speed, somebody would have some tip ?

tanks,

Alexandre

How to change of the license level 5 for the 6? It is possible paying only the value difference or I will have that to acquire level 6 for the integral value?