MikroTik

liviu2004

I don't see a reason to complicate with Capsman, for one AP. To be honest, I tried Mikrotik wifi for many many years but I was not entirely happy with it. Since moving to TP-Link AP, uptime has been amazing, almost to the point I forgot about them. And they do VLANs just fine as well. If you would o...

liviu2004

Were you using quick setup on both devices? While this might work to some degree, it is not the best approach, especially when both units are fighting on who is the router in the house...

liviu2004

why? Well, I noticed that the value is ridiculous. On most devices it is higher than CPU temperature, one one device even 10 degrees higher. Probably someone has researched that and concluded that the circuitry is wrong and the value cannot be used. It is still advertised as having PCB temperature ...

liviu2004

So those devices can only cool in front. Do you see the problem?

liviu2004

*) health - removed board-temperature on RB5009UPr+S+IN device;

why?

liviu2004

That part from the manual is new to me. It could be right, it could be wrong, I expect the later, considering my setup works stand-alone with LTE interface VLAN. Mikrotik would not accept untagged packages on a trunk port. The tagging of ETH VLAN is introduced with the latest firmware of v3 and it i...

liviu2004

For testing, I removed all to do with pppoe-out1 config, and reverted to classic config, no Policy Routing. VLANs not touched. All work as should, so the LTE VLAN50 route through AP works?

liviu2004

Switch is an CSS610-8P and is as well pretty simple to configure. Done one or two mistakes there in the past and it becomes very obvious when you do that, because of services not working. switch2.JPG switch1.JPG Indeed, LTE is not directly connected to Router. I tried 4h to pull a cable next to anot...

liviu2004

All wifi and some connected to the AP which is directly wired to the router. APs are TP-Link EAP245 and their VLAN setup is pretty straight forward. It must be the router, if I just make a simple config, one WAN, no vlans, more or less default, without changing APs and Switch, they all work fine. Bu...

liviu2004

For testing, I connected my phone to Internet_of_Things and I can browse no problem. Funky these IoT devices. I also connected light controller to Internal_LAN and was no improvement. Point taken on (14) and it makes sense, I think my brain was locked for many many years. (4) I haven't include it ye...

liviu2004

1st issue encountered, and seen this before: all IoT devices in house lack internet connectivity. Example, Home Zone Heater shows status: Connection issue. Light controller shows no internet connection. Washer and dryer no data shown in phone app. In router, light controller connects and disconnects...

liviu2004

Thank you very much, I am f...ng impressed. I need some days to digest this. I need to provide some feedback to some common sense items you mentioned. (3) For security added Trusted Interface, assuming the one subnet that is trusted is your internal network vlan10 nice one (4) What is the purpose of...

liviu2004

This is weird. I am doing a speed test from VLAN10 and both WAN routes are used in the same time? This is really messed up somewhere.

Capture.JPG

liviu2004

Thanks for the directions given. I'm avoiding combining Mange and Policy Routing, but I need that change the TTL on LTE. Following changes now implemented: - add default routes to both LTE and ppooe (VDSL2) WAN connections so they come into the Route List, and as you mentioned, it was also described...

liviu2004

Nope, still issues. After a while, IoT devices started complaining about connectivity issues . Then I enabled Add Default Route to the WAN LTE19 DHCP client and things got restored. So I am running in circles, if I enable add default routes of WAN, cannot control where traffic flows towards WAN, if ...

liviu2004

I might of solve it. Solution (to be confirmed long-term): remove default route from the WAN LTE19 DHCP-Client, remove add default route from the WAN pppoe-out1. And add Routing Rule to be able to access WAN KPN modem from VLAN10 /interface pppoe-client add disabled=no interface=vlan6 keepalive-time...

liviu2004

I need help with the following setup. Home user. Attached network diagram. The traffic flow requirements are as follows: 1. VLAN 10, 20, 30 and 60 access to internet 2. VLAN no intercommunication with the exceptions: a) VLAN 10 access to VLAN 40 for IP Camera and NAS b) VLAN 30 access to VLAN 10 for...

liviu2004

We're really deviating from the topic scope, but one more to be forgiven. I agree with you and as well want to keep it realistic. You are asking a bit the impossible. I am looking around, all sorts of forums. What one sees here, sees everywhere. Could MT impose restrictions on 1st post, yes. Would t...

liviu2004

Fully agree anav, you are having in mind a full path to success, starting with the most basic question: what does the "client" need?

liviu2004

I came across this topic searching for guidance how to route some vlans to another wan. What I wanted to add is that your last post does not deal to vlan local traffic, basically everything arriving in vlan in sent straight to WAN. Not ideal. The mangle rule should disregard local traffic by negatin...

liviu2004

You would need as a minimum:
- show configuration, use this button </>
- specify which hardware you use.

liviu2004

XV2-21X AP datasheet says consumption is 11W typical. It's not meant maximum.

Questions to Gary:
- what is measured peak consumption?
- what is the maximum dV/dt?
- at which voltage input radios turn down in power?

liviu2004

I think I got this working. Access Point with 192.168.1.4 in the diagram is an EAP245v3, for which I assigned on second LAN port, VLAN ID 50. On the router side: - Interface list VLAN with ID50, name LTE4, assigned to bridge1 - Interface list, add on WAN the LTE4 - Bridge VLANs, added 50 to VLAN IDs...

liviu2004

I use draw.io which is for free as well.

Let me give some tries to your ideas. Thanks for suggestions.

liviu2004

I'm unsure if you replied to me, but I would assume so. /ip firewall mangle add action=accept chain=prerouting in-interface-list=LAN dst-address-list=connected-subnets This does the trick, however, I do not want inter VLAN traffic, unless the parts I specified for, e.g. access to a printer. I know m...

liviu2004

Recently I got an old LTE4 device, which I need to install high in the house, to get some decent reception and speed. But for the life of me, I cannot get an extra cable in the existing plastic tube. Tried for 3h today and damaged 10m of line. Is there any logical way to use the same cable going to ...

liviu2004

Thanks, I read again the specs 5 times 16W is all the rb450gx4 will take. 500 mA for port 5 poe out will be sufficient for the eap610.

liviu2004

So while the topics title, "vlans do not work" suggests that VLAN tagging stopped working, actually routing between connected subnets (which in your case happen to occupy VLANs) stopped working. But you want a solution, right? One possibility is to create an address list of all the connec...

liviu2004

I need help understanding PoE out for RB450Gx4. From the datasheet: Max power consumption 16 W Max power consumption without attachments 4 W Max out per port output (input 30-57 V) 500 mA If max power consumption is maximum 16 W, how can the poe out be 57 V x 0.5 A = 18.5 W + 4 W internal use = 22.5...

liviu2004

I don't know if this is necessary for PPPoE connections, but I would recommend to at least try the following: Set `accept-router-advertisements=yes` in /ipv6/settings Set `add-default-route=no` in /ipv6/dhcp-client: route, normally, should be learned via RAs (but it might be a peculiarity of PPPoE ...

liviu2004

It seems wrong to me to have an interface set on the "default" record. It also appears that you do not have ND on LAN interfaces, did you omit the output? I must of misunderstood one of your previous posts. I have corrected the ND configuration and indeed, it appears to work without RA li...

liviu2004

Nothing, you just need to ensure that the supplied source is sufficient for the RB and your auxiliaries. Failing that, you need to buy a higher rated power supply.

liviu2004

1. I have RB5009 with CSS610-8P, in the beginning I had lots of errors in the CSS610 but vanished by themselves. RB5009 handles all firewall rules ipv4 and ipv6, 3x VLANs, two APs (one directly, one through the CSS610) and also an IP camera. It does not even sweat, however, I am yet to receive the 1...

liviu2004

Not disagreeing that something else might be not right, however, I have no functional complaints. Herewith the output of /ipv6/nd/export. # 2024-04-04 17:22:54 by RouterOS 7.14.2 # software id = LRF1-VRV8 # # model = RB5009UPr+S+ # serial number = /ipv6 nd set [ find default=yes ] advertise-dns=no h...

liviu2004

Dear CGGXANNX, it is exactly like you said. All set according your post, as well on ipv6-nd, then I saw an avalanche in the logs about pppoe connecting and disconnecting. It took 24 tries before the pppoe connection established, I was about to go back .... Thanks, I could of not figure it out by mys...

liviu2004

Most of the settings in /ipv6/nd are for the case when RouterOS is the Advertising Router, i.e. when it sends a configuration. However, in case of the PPPoE interface it's acting as a Host because it receives a configuration. Well noted. You, most likely, want the following settings on pppoe-out1: ...

liviu2004

I appreciate all the help,I read everything and applied accordingly. I still want to read the documentation and understand what settings affect what, in the meantime, problem is solved as follows: applied MTU of 1480 in IPv6-ND. IPv6 test website shows a result of 10/10 in an instant. This is agains...

liviu2004

I've set pool-prefix-lenght=64 on the dhcpv6 client, but did not made a difference. From various posts about my KPN ipv6 settings, I always found 48 to be used and I see the prefix I get is also /48. My feeling tells me that 48 is all I will get? I've set advertise-*=no to yes in the ipv6 nd setup a...

liviu2004

Hi, trying to get my ipv6 going, I'm not fully grasping on the basics and settings.It appears I can obtain an prefix from my ISP, I seem to get an IPv6 address for my PC but when I activate dhcp client on ipv6, I cannot access mikrotik.com anymore and ipv6 test website shows me fail all tests. I'm f...

liviu2004

Thought you could not combine old capsman with new cap ax wave2 drivers things like that. It has been written before, give a search.

liviu2004

Invision power ip.board? i can donate you a license.

liviu2004

Just don’t tell anyone. Keep it your secret.

liviu2004

Come have a look. And maybe you combine with a nice trip to the Netherlands.

liviu2004

It barely fits in the bolts of the mikrotik rack. I had to use force in order to bolt it down. The adaptors would need to be 2-3 mm longer.

liviu2004

That tells not much on pcb setup. I can put 4 pins anywhere and connect only 2. You can have a detailed look to the pcb.

liviu2004

Does the hardware have pwm speed control of some sorts? Otherwise you can wait until year 2500 for software solution.

liviu2004

Why just another device in house? I agree this bad behaviour should stop. In NL this is not permitted anymore and anyone can use whatever equipment they like and fits the provider technical.
So lets stop with this bridge mode bull…t publicity.

liviu2004

Solution for you:
viewtopic.php?t=45259

liviu2004

In 2023 2 devices cannot autonegociate and maintain a 1gbps link…..

liviu2004

Do you think mikrotik will come on a forum and say:
Yes, this is a known hardware problem.

Without even seeing the box???

Get a reality check for your expectations.

Send it back!

liviu2004

Send it back.

liviu2004

Set it back to the seller for warranty. Put some evidence in the package as well.

liviu2004

You cannot setup capac from hexs like that, unless capsman, but that is really not needed.

If in hexs ports 2,5 are in a bridge, set manually IP at your pc in the range of capac; is that 192.168.88.1? Then make yours 192.168.88.2. And open winbox and connect to 192.168.88.1.

liviu2004

Broken because it lights up a few seconds after power on?

liviu2004

I don’t see how this can sit in my living room ceiling. Way way too big.

liviu2004

https://youtu.be/FTQEnDZVHNc

liviu2004

When it will be ready.

liviu2004

Is there any product restricted to be sold to businesses only? No.

liviu2004

http cookies timeout how long? Login by cookies disabled?

liviu2004

Then switching to another os makes no point?

liviu2004

Same here, css610-8p-2S+in with srj10+ brand new out the box, tested 3 cables brand new against a NAS 10gbe port, buffalo Terastation with windows storage servers. Tons of tx fcs errors.
Dissappointment is an understatement.

liviu2004

Hm, worrying, have css610-8p and sfp+ modules coming in tomorrow.

liviu2004

That’s why one should never buy fan cooled equipment in home environment.

liviu2004

There are no brackets for wall mounting. But there are brackets for a rack mount.

liviu2004

I have this switch. You can bring internet to any of the ports, it just doesn’t care which port you use.

liviu2004

No issues, what voltage do you use to power this up and what is the loaded voltage at the unit?

liviu2004

Is it??? Wow, have to check this out. Is there a script to turn them off at night? I don’t need internet while sleeping … yet.

liviu2004

Disclaimer: I know not much, so I might say things which are not correct. I am using Mikrotik since the times of RB450, tbh I did not know what I was buying and took me forever to get internet home. Times change, so the equipment, so I am now recent user of an RB5009. Except that my internet supplie...

liviu2004

I saw somewhere in rc that it was now.

liviu2004

Yep, got one, looks good. How would one mount it on a wall? I have a shelf stand-by in any case.

liviu2004

I don’t think was meant like that, at least initially. I guess we’re all people and make some mistakes?

liviu2004

Post config hide sensitive?

liviu2004

No sector writes statistics on hAP ac^2 (WinBox 64bit v3.37).
res.png

Available on RB5009 still.

liviu2004

I know not much when it comes to fiber connections. RB5009 to CSS610, if I want to setup 10G fiber cable, distance from living room to man’s cave, about 10m, which modules do I need to buy? Preferable mikrotik. And cable, is that doubled? Multimode, single mode? Can be bought at lenght, ready made? ...

liviu2004

Do you test on cable, wifi, 2g or 5g? You might want to drop dns open resolver, why do you need that? To be part of ddos attacks? You’re one of the bad guys?

liviu2004

Perfect solution for you:

viewtopic.php?t=45259

liviu2004

I cry. You happy now?

liviu2004

/ip dns
set allow-remote-requests=yes

That setting made my ISP to shut off internet to me, blaming my IP was used for malicious attacks. I had no clue what it did in those days. Is there a good good reason for you?

liviu2004

Is that a joke, not select a country? Why is there a setting to begin with?

liviu2004

PoE in 802.3af/at (ether1), Mode B (ether2-ether8)

liviu2004

Has this been concluded?

liviu2004

Have a look here:
viewtopic.php?f=2&t=156563

liviu2004

I've played with Tx Power because I haven't seen the Antenna Gain. What a pain from user point of view to enable disable the wifi, just to try things out. But thanks for the tip.

liviu2004

Thanks all, very good suggestions. I run the latest version always (no beta). What did the trick was indeed the Tx Power. I got confused with antenna gain. Yes, on 2.4 GHz I want to run low powers, as I have two AP in the house and want to keep each one with own area. I changed 5GHz channel to 5180,...

liviu2004

Hi, I've looked through similar topics but I am in a dead end. Got this cAP ac, RBCAPGI-5ACD2ND. These ones: https://forum.mikrotik.com/viewtopic.php?t=113997 https://forum.mikrotik.com/viewtopic.php?t=112896 https://forum.mikrotik.com/viewtopic.php?t=137836 https://forum.mikrotik.com/viewtopic.php?...

liviu2004

My site does not work either, I have a created a topic for that.

liviu2004

I've downgraded to 6.40.5 and all fine. There is a problem with 6.41. I don't know what, but for me was bad.

liviu2004

And its done, today no longer access. I'm not really fun of downgrade, it always goes wrong with me.

liviu2004

Hi, thanks, it is my own forum. I've called the host company and they confirmed my IP is not blocked.

liviu2004

With an CCR and simple config, it works just fine. Software 6.40.1. Now, how do I explain this: without changing anything, while I was busy with the CCR, lets say 30 minutes, I plugged back the VDSL to Mikrotik RB493G and guess what, it works now. No reboot nothing. Problem is, this lasts a day or s...

liviu2004

I've just tried that using google DNS but no result. What I find odd, with my laptop Win 10, with simple PPPoE interface, connected to internet provider, all works fine. So I would not suspect DNS trouble. I conclude something odd happens with my Mikrotik. I have an Cloud Core Router with older soft...

liviu2004

I've tried that workaround, however without results. Why would only one website be affected? Do I need to change my host? Is anything in my config wrong? I can ping 37.251.143.31 and get around 48ms reply. Sorry for so many questions. I've logged above rule and got this: forward: in: bridge1(wlan1) ...

liviu2004

Hi, this is over my head. I can't access my own site, corsa-c.ro. It was ok for years until recently. It won't work in my LAN but on phone 3G works fine, so website looks good. On phone, on WiFi, also no connection, so can exclude the PC. I run a Mikrotik RB493G as router, firewall, access point and...

liviu2004

Immediately after update. 1. interface, warning ether6: bridge port received packet with own address as source address (64:d1:54:3c:be:89), probably loop. There is nothing connected to ether6 (it is master port). Router is RB493G. 2. Connection with wAP ac fails frequently, had to abort connecting t...

liviu2004

I find Mikrotik and RouterOS great, sometimes I shoot my own foot, yes. I don't think I would like to search any other router at this point in life; remember, sometimes you will get some hits from it, however, there comes much support from Mikrotik and these people on the forum, that is impossible t...

liviu2004

I am actually not running RB3011. I have RB450 and RB493G, both affected. So it does not matter on which switch port group.

liviu2004

Same here.

liviu2004

6.38 is unworkable for me, pppoe and dhcp no go.

liviu2004

You are not the only one, same here. Very unstable 6.38, dhcp is terrible, i had to pull out 2xrouters and put back kpn xperia box. I havent use it from 2009.

liviu2004

it helped me.

liviu2004

So, after three years I manage to solve few of my wishes. Setup is as simple as possible: 1xWAN connection 4xLAN connections setup as switch dynamic queue arranged for load balancing between users (pcq type). Recently I have learned how to update from 3.6 OS to 5.2. Operating with winbox is much fas...

liviu2004

Got it. Thanks guys. It was easy but if you didn't do it before, is hard.

liviu2004

You are right. Single beep and then 2 beeps. I will try to connect to it. Shall I use ethernet cable? What IP should I put to my ethernet card? Anyway I have installed yesterday Virtual PC as I have seen in tutorials which came with the router. Something happened. When I boot up this morning my inte...

liviu2004

I just bought an routerboard 450. I plugged power supply to it and a blue light is on.

How should I install OS on it? I received a CD with the package but I do not see how to connect and download the OS. Shall I use serial port or Ethernet port?

Any help will be great.

Search found 104 matches