Hello all, I have been using an RB4011 for the last few months recently it bricked. wifi was working but all ports were off and the despite the wifi being on no dhcp was present. The unit was noticeably hot and attempts to reset it failed. I have since taken it down and replaced it with its older br...

Due to the latency differences I would setup load balancing on the two adsl. I would then forward the mail server through the Sat connection as mail services not heavily affected by the latency. Your users will this way have access to their mail from outside and will have a good browsing experience...

Hello Guys, its been a while since i was here. i have just completed an upgrade to one of my oldest networks i have installed a CCR1009 as router and and 2 CRS as switches among an array of mikrotik ptp radios etc. the problems i have. network: 3WAN: 2 adsl (1 static public IP one dynamic) + 1 sat (...

i want to have request if you have drivers for the usb celot coma/evdo modem
http://www.celotw.co.kr/product03.asp

please advise as i would like to integrate it onto a 493G

regards

LM

I have cisco 2960 (managed) switches on both ends of the link.
what can be done?

regards

Louis

Hello all,
I have a transparent bridge setup between our core sw (cisco 2960) and Base station Switch (cisco 2960)
I would like to map vlans on this link. Is this possible? In a nutshell, can you map vlans on a trasnpareent bridge?

regards

LM

according to the wiki the atom family is much lower consumption than the pentium family. http://en.wikipedia.org/wiki/List_of_CPU_power_dissipation Pentium III 800 Coppermine (180 nm) 800 MHz 27.2 W or 26.4 W 34 (27.2 W), 33 (26.4 W) Pentium III 800EB Coppermine (180 nm) 800 MHz 29.05 W, 27.2 W or 2...

does it mean that for the purposes of lets say a SOHO router, or hotspot manager, that the Nvidia Ion Motherboard atom230 is underpowered?

regards

lm

hello all, is there anyone using the nvidia Ion mini itx boards to the run RouterOS and what results are you getting? regards Louis example: Zotac IONITX-C-U Atom 230 Manufacturer Part# IONITX-C-U Product Type: Desktop Board Form Factor: Mini ITX Memory Technology: DDR2 SDRAM Processor Technology: H...

Is it possible to develop drivers for Kyocera Iburst usb modems. We have an Iburst network in Kenya and if we can have this supported it can help greatly. router supporting iburst usb http://www.dovado.com/umrmodems.html When i connect the modem the iburst modem it is visible under /resources usb as...

I am interested to connect the USB kyocera Iburst modem to connect via pppoe.
Does mikrotik support Usb Iburst devices.

i have connected it to the unit and under usb resources it has been detected as Kyocera Iburst terminal.

can you assist?

-LM

Hope that you have some ideas as i am on site for a few more days before returning back to my country. it is important to close these problems soon.

pls help even if it means going back over what i had done earlier.

-LM

Hello all, My problem is that 1. i would like to provide internet access to about 8 users out of a pool of 30 users how best can i implement this ans the internet connection is very small i.e. 128kbps 2. I have a /29 public ip pool and would like all users to be able to get services off the servers ...

Hello all, In a twist I have set up a web proxy on a rb192. I have bridged eth 2-5 as a wan hub and eth 6-9 as a Lan Hub with eth1 as GW. users in the lan can browse he internet etc but they cannot reach the mail server which is connected to the eth bridge 2-5. What could be the problem? have tried ...

Setup information: RB493 as router on a vsat connection with a LAN of 25-30 users. The link is filling up quickly and i would like to give some users more bandwidth in reference to their seniority and need . however, I have some smart alecs trying to beat the system by giving themselves static ips. ...

Services -> web port set to 80? no NAT rules redirecting to port 80? services port is on port 80 and there are no nat rules using that port either. I have a port forwarding to an internal server but its on port 8080. I noticed that i could not get the www page after creating a webproxy and when i d...

I have a router which i have set up to use a web proxy but soon after the setup i was no longer able to view the www page.
i have since removed the web proxy but the mikrotik page stil does not show up.

how can restore the www page back so the client can view their graphs?


-LM

Hello all, I am setting up a 5gh network on a 333 ap however i need to connect this AP to the office via a ptp bridge ( 2x133 flatpanel). i have 2 public ip's allocated and i want to set 1 on the ap eth0 and the second on the one office side of the Bridge. Is this possible? What i have in mind is to...