MikroTik

edmundas

Hi, I'm doing simple policy routing as I have 2 isps but I'm unable to run hotspot. As soon as I setup hotspot on one of the interface of ccr 1036. Hotspot doesnt works. Tried whatever solutions I found on forum but of no help. config is simple isp1 ip xxxxx isp 2 ip yyyy isp1 going with default rou...

edmundas

is it normal that if one of the gateway is unreachable still it shows reachable. Then what is the use of check gateway parameter ?

edmundas

Hi, I have 2 isp and I'm doing ecmp with 2 gateways in single route with check gateway. Upload is balanced fine but when one of the link fails that gateway still shows reachable in routes. It should show unreachable. So my traffic keeps on going on the down isp . Tried check gateway with ping and ar...

edmundas

i have 2 bricked after upgrading to 6.15 on 2011. Netinstall failed to discover the device. Give it a reset it will work only till next reboot.

edmundas

hi,
i'm doing remote logs of firewall but i dont want these logs to echo in mikrotik routeros. Can anyone tell me how to do it
thanks in advance

edmundas

Hi, I bricked 2 rb 2011 after upgrading to 6.13 and 6.15. After upgrade router became dead. No led lighting after connecting ethernet on 6-10. Reseting bring back the router but only for once after reboot its again bricked. One of them after few reboots starting working. The 2nd one even after downg...

edmundas

on which email id should i sent to make MT responsive

edmundas

mail was sent to support@mikrotik.com

edmundas

Hi,
How to get advance channel licence as it gives error of licence. I'd sent mail to support but they have not responded.

thanks

edmundas

edmundas

Hi,
Unable to install Mikrotik 5.26 on Gigabyte b75m-d3h board and kingston ssd. Error comes "No hard drive found". Is intel b75 chip unsupported by 5.26 ? Sata controller is running in ide mode

thanks

edmundas

hi,
A feature request to add Mikrotik-Host-IP to be used in access accept/reject request to bind the request from IP (before translation)
If this user and pass request comes from this ip then only it will be allow. Same as calling station id but instead of mac address it will be IP addresss.

thanks

edmundas

Hi, I'm trying to use MT dhcp server for docsis provisioning. It's just a basic one. Just dhcp release and sending single config file with tftp. It releases the IP address but fails to send . Tftp server is trying to send the file but is unable to send the file. Here is the log :52:59 tftp,debug req...

edmundas

Hi, There is a router(cmts) between users and mikrotik. Users get ip address (cm etc) from provisioning server. Then they authenticate with pptp protocol to get their internet access. As there is a router between Mikrotik and users I cannot use hotspot or pppoe. There is no option for cmts to run in...

edmundas

Hi,
What is the use of Radius AV Mikrotik-Host-IP. I want to restrict users to send login request from a particular IP. If they change their ip then they wont be able to login. Using radius as backend AAA

thanks

edmundas

hi,
how to do port isolation on rb 2011. Port 6 to 10 isolated.

thanks

edmundas

tried using the packet mark in simple queue but no packet passing through that queue. Whereas iptables is marking the packets.

edmundas

then what is the work around if there is no fix. Mikrotik is silent. They should post it on wiki for workaround (if there is any work around)

edmundas

I'd same problem on 1100ahx2 ver 6.0 rc14. Nowdays I dont dare touch any MT with ver 6.

edmundas

Hi,
Is there a way to assign a subnet like /29 /28 to hotspot user with radius at backend. This subnet will be dedicated to that user only.

thanks

edmundas

Hi,
This question has been asked repeatedly and no one has ever given the answer including support.
HOW TO BYPASS THE HOTSPOT QUEUES FOR CACHE HITS OR SOME OTHER SERVER.
ON version 6 and CCR

thanks

edmundas

Hi, Never expected rc 6 will be so buggy. In my experience of MT of over 10 years, I havent seen a buggy release like this by MT. Suddenly my ccr16 hotspot stopped passing traffic thru queues. Everyone was getting wht ever they could pull (v6 rc14). I'm scared to change any other version as some ver...

edmundas

thanks for the suggestion to downgrade to 5.xxx. Can i do on ccr

edmundas

so i'm not the only one. Mikrotik ppl are reading this ??

edmundas

+1 i was attacked too as my allow remote request was enabled. More used to working on djbdns or bind which are more secure. They should add allowed subnets in their dns server. Moreover in earlier versions allow remote request used to be off by default if my memory serves me right. Now its on by def...

edmundas

hi
someone tested rb44ge for routing and comparison with intel 4 port server lan cards ?

thanks

edmundas

hi
suggestion needed for 3gbps routing with firewall and queues on 1 wan and 1 lan situation. What h/w sill suit best in this case.
thanks

edmundas

i'm getting ddos on my router on wan interface. I used ddos prevention based on http://wiki.mikrotik.com/wiki/DDoS_Detection_and_Blocking the only diff was the incoming interface was added as wan. It was preventing ddos then one day all the packets were able to bypass these rules. The attack was as ...

edmundas

hi, how to bypass queues made by hotspot or pppoe server. It was running fine in version 5xxx but after shifting to ccr with ros 6 this has stopped working. The marked packet and adding queue on that mark doesnt get bypassed. The traffic goes through the dynamic queues too. There was no problem in v...

edmundas

after changing from rb 2011 to ccr. simple queues are handled before queues tree and both are used. For instance
hotspot queue is handled after zph marked packet queue it passes thru queue tree then simple queue. So benefit for zph

edmundas

i have 2 bgp peers 1 telco 2nd client
i want filter not to advertise any route to cllient. just default route should be advertised. help would be appreciated

edmundas

thanks for your support. I have some queries.
when i connect to different AS like 65000 and 65001 why does it shows in mikrotik <>>bgp <> advertise<>origin ---- igp.

thanks

edmundas

just received rc9 from mikrotik and the problem is resolved.
Thanks

edmundas

for example
a 65000-cisco
n 65001-mikrotik
c 65002-cisco

65001 peering 65002
65002 advertising route 10.11.12.0/8 to 65001 with local pref 110

65001 peering with 65000 and advertising routes of 65002 with local pref 110
thanks

edmundas

they are static routes. we had added bgp local pref = 200 in static routes. but still my peer shows no local pref

thanks

edmundas

we were planning to replace cisco with ccr before replacing we thought of doing a simulation of router which it was going to be replaced. We made a labtest with linux quagga and rb-2011 router to check bgp. We were able to solve most of the things done on cisco but unable to advertise local-pref. Ev...

edmundas

support.rif has already been sent and support has reverted on the same.
had u tested neighbours with pppoe server on ?
shall i give u read only account in mail ?

edmundas

Hi, I installed ccr 1016 replacing 2011. With 2 bridges. Bridge 1 ether 1 to 6 and bridge2 ether 8-10. Extensive drops on some ports and 2 ports (6 and 10) were unable to communicate with the devices.I'd to use switches to run the network. Neighbour discovery adds every interface like pppoe users, m...

edmundas

i dont have ac power supply so i want to use poe

edmundas

wht is the power consumption of rb 1100ahx2. what Poe power supply shud be used.

how much pppoe users 1100ahx2 can handle ?

thanks

edmundas

I'd limited the connection limit on ports tcp 1024-65535 but still my port 80 gets limited and I get errors of connection reset chain=forward action=reject reject-with=tcp-reset tcp-flags=syn protocol=tcp src-address=192.168.100.0/24 out-interface=bridge-local dst-port=1024-65535 connection-limit=50...

edmundas

is there a way to run multiple hotspot or running hotspot along with other captive portals. As hotspot spoof the arp response, bcoz of which other authenticating services are hampered. Disabling UAM in hotspot or MT ver 2.7 type hotspot

thanks

edmundas

Couldnt keep my client's network down. 2011L seems to be a buggy product. On 450 its working well.
Returned all 2011l back to vendor

edmundas

Hi, We installed few 2011ls with the configurations port 1 - 5 bridged(bridge-local) with wan ip address on it port 6-10 are already bridged (ether 6 was removed from bridge-local) port 6 to 10 using hotspot service or pppoe server 1-5 ports working as wan switch on port 6 - 10 on all installations ...

edmundas

i'd already done tht and explained in the post
1 pool for dhcp which is private ip
2nd pool for hotspot which is public ip
all public ips are routed but users dont get login page
regards
ed

edmundas

its not working. Ppl are unable to get login page. I cant ping to them too. Here is scenario Pool 1 : 172.16.0.1/24 Pool 2 : 28.122.8.0/24 Pool 1 is given to dhcp Pool 2 is given to hotspot server I can see host in hotspot where 172.16.0.x is converted to 28.122.8.x. In arp table all entries are for...

edmundas

so tht means i'll have 2 pools one for dhcp leases and other for hotspot
regards
ed

edmundas

Hi,
How to setup for 1 to 1 natting in hotspot where clients will be getting private addresses from dhcp server and hotspot doing 1 to 1 natting to public ip address.

regards
ed

edmundas

i think they are switched device wont work well in bridge mode.

reg
ed

edmundas

100mbps

thanks
ed

edmundas

Hi,
Someone suggest me MT hardware for traffic shaper in bridge mode with 3 or more ethernets.

regards and thnks

ed

edmundas

some websites need to be bypassed from bandwdith management.

br
ed

edmundas

Hi,
we want to bypass bandwidth queues for some sites where mt is running as nas.
custom iptables rules based on radius attributes like tcp limit for certain users
regards

ed

edmundas

Hi, I'd been trying to connect openwrt (atheros) based station with mikrotik ap. My scenario is mikrotik ap and openwrt clients. Mikroti is running in ap bridge mode with wds = dynamic and stations are wrt in station mode and wds=1. They are connected but can't ping each other. Signal strength is go...

edmundas

Hi,
I'm unable to connect mikrotik ap with openwrt client. It connects but no pings.
AP
RB133c 2.9.38
mode ap bridge
wds dynamic

openwrt
mode sta
wds=1
it a back to back test with both just 5mtrs apart. anyhelp would be appreciated.
regards
ed

Search found 55 matches