We have a job coming up in a warehouse with some long Ethernet runs for access points. We will be using CAT6 cabling. If we use standard 802.3af POE switches and access points that are powered 802.3af, my understanding is that the GPER can go in between and the switch should power the GPER and the a...

I had very poor signal when the unit was laying on a flat surface about 6 ft off the floor, once I hung it on the wall with ports facing the floor at about 6.5 ft from the floor the unit has performed way better than expected. Going through 5 walls I have pretty much a -48 on 2 MBP, 2 MB, 2 iPads, 1...

I have tried with the switch configured and left at default. Maybe you are on to something with the mac address, I did adjust the mac on the two ssid's to be different but not on the bridges or anything because I've not ever messed with them before but not dealt with this built in switch before eith...

This isn't working, it's like the wireless doesn't pass traffic unless something is plugged into the rmxxx port or service port. Although it seems to pass vlan20 to the service but vlan10 gets an ip on the rmxxx but few seconds later it's gone and doesn't work after that. I know x86 version is worki...

Actually my config isn't working correctly. Can anyone help me to get this working or if it can't do it to tell me that as well so I can quit chasing my tail.

If any more info is needed please let me know.

Thanks

Here is what I have so far and it seems to function but I just want to make sure this is the correct/optimal way. And I am adding these units to go with an existing wireless setup that is all based on Cisco 1131AG APs so I've set the 951G's to just do B/G as I'm not for sure how bouncing between N a...

I'm new to the switch settings and not seeing an example that fits exactly and wanting to make sure I set these up efficiently as possible. So I have a Cisco 2960 with a port setup as a trunk for VLAN 10 and VLAN 20 going to power inserter then to ether1 on the 951G. I need it to be a trunk so that ...

I am about to upgrade a network to managed switches to add vlans and needing 2 small switches that can pass one vlan trunk with 4 vlans on it. The had an ethernet run that was almost 700' to another building and was having issues needless to say, luckily I was able to fit 2 switches into a large con...

Ok got an old 532 that has been sitting and figured I would take another stab at fixing it. The ether1/POE port is dead so netinstall is a no go unless I can load the ethernet image it transfers to CF and boot it that way. It was working and running Mikrotik but in an attempt to get ether1 working t...

It works great function wise, but can you open more than one winbox.exe at the same time without multiple copies of the file renamed or duplicate files in difference directories? Maybe I am just weird but I hardly ever just have one instance of the program running. I would gladly use free if that's ...

I had this working at one time I think but for some reason after reloading my iMac I can only launch one instance of winbox, this is very annoying because I usually have 3 or 4 opened at a time. My workaround is to duplicate and rename the files winbox1.exe winbox2.exe etc.. Problem is saved login i...

I saw where someone sent support a sniffer file and that helped fix the xbox360 upnp problem, and I would like to do the same for back to my mac/mobile me for the mac. I have an RB133 I can put 4.6 clean install on. I had planned on just a basic setup for dynamic wan ip with masq enabled, no rules o...

This still does not work! Any help would be great.

Thanks

Not exactly the same thing but how has the macs mobileme or back to my mac been working with mikrotik? Anytime I am behind a mikrotik I always get back to my mac is not working properly because it requires a router that supports nat-pmp or upnp. Upnp is on and does work for other applications on the...

Any ideas on this one? If you need any more info from my configs I will gladly post it.

Thanks
Jason

I tried another upnp app and it creates the rule but when I issue the print command it does not have the dynamic created upnp rule listed. The app is transmission and it does show the port as opened.

Thanks
Jason

Sorry I thought you wanted the upnp config. Here is the firewall config, very simple. Although I do not see the dummy rule in the list. And there are 6 macs all on mobileme connected to the network. /ip firewall nat print Flags: X - disabled, I - invalid, D - dynamic 0 chain=srcnat action=masquerade...

Thank goodness I am not the only one having trouble with MobileMe :) I also am unable to use the Back to my Mac services. I was using smoothwall before replacing it with Mikrotik and it worked great, only thing I changed in Smoothwall was to enable UPNP. I will also post my upnp config to help out. ...

I tried the simple queues and tried to specify an ip subnet but that seems to set a limit on the entire subnet. Such as if I set a limit of 128k down that is for the entire ip range two users would get 64k each. How can I set a limit of say 128k or whatever to each ip. So if I had 2 users they both ...

I am trying to setup wireless for a travel park. There is a RB532A as the main AP and and 5 RB133's setup as WDS nodes. I have a cable modem with 10Mb down and 1Mb up. I have one SSID for the residents of the park and also another SSID for guests. I have setup 2 DHCP pools one for each SSID handing ...

Ok I searched a little but not exactly seen the answer to what I am looking for. I have a 2.9 MT box with 2 ethernet cards and adding a wireless card. I have all adapters recognised 2 Intel's and a D-Link DWL-G520 (detected as Atheros AR5213). I have a Public interface (Intel), Local (Intel) and the...