I am looking for feedback if someone has incorporated a small Java VM on top of RouterOS. For example, JamVM being one http://jamvm.sourceforge.net/

Hi, Is there a theoretical limit on the number of PPPoE client sessions that can be initiated from a RB1000. I have a test configuration consisting of RB1000, Juniper ERX 310 as a LAC and a Cisco 7204 as a LNS. I have no problem in establishing the first 14 PPPoE session's, but on the 15 PPPoE sessi...

I have a test configuration using 2 MT v3.25 connected directly via 3 Ethernet ports which are bonded configured for balanced round robin mode. In this test configuration, I have arp enabled for link monitoring. Running bandwidth test, the behaviour is as expected - each link carrying 33 Mbps of tra...

I have configured HTB on a bonded interface and under certain conditions, in Winbox the queue change colour from Green to Red. No packets are dropped during this time. Stopping the traffic causes the queue to change colour to Green Any idea on when a Queue is RED, what it means and how I can investi...

Need help on PPPoE authentication using FreeRADIUS. MT sends authentication request to FreeRADIUS; FreeRADIUS returns back with a Access-Accept response, however MT terminates the PPP session with the following error - authentication failed because of RADIUS timeout. Using Wireshark and Packetsniffe...

I am in the middle of testing L2TP tunnel between Router OS 4.3 with our service providers Juniper router. The sequence is as follows: 1. Juniper send SCCRQ message which includes a challenge AVP. 2. The MT responds with a SCCRP with response. 3. The Juniper responds with Stop CCN message and thus t...

Looking for suggestions on the following: 1. Is it possible to disable authentication for PPP? Tried it through Winbox and Router OS requires atleast one authentication type to be configured. 2. Anyone out there tried configuring a secret with wild-card name? I understand Cisco and Juniper support t...

Thanks - I agree from a forwarding perspective. More specifically, is Router OS architecture single or multiple threaded with priority support. For example, if the OS gets ICMP packet, SNMP request and OSPF routing update at the same time, which one will it process first or is it on first come first...

When Router OS performs packet processing, are ICMP ping packets prioritized higher or lower or same as other packet traffic.

Has anyone tried using RB1000 as a LNS with Cisco/Juniper as the LAC?

Using BCP bridging (PPP tunnel bridging) configured on 2 RB1000, I can get PPPoE tunnel working into a L2TP tunnel. The specific question, has anyone got RB1000 LNS based on BCP bridging working working with a Cisco/Juniper LAC.

I have a Router Board 1000 running OS 3.3 and tried to configure Jumbo Frame on L2TP server. Winbox came back with a message that for Max MTU the supported values were between 512-1500 bytes. Ether2 and Ether3 are configured as 1Gbps full-duplex. The following link gives the impression Jumbo frames ...

I would have expected CC1 to return to Master + Running state as opposed to just Master.

Not sure if this is known bug with VRRP. I am currently using Router 3.3 OS and performed the following test. 1. Configured CC1 (Master) and CC2 (Backup) in pre-emption mode. CC1 and CC2 both connected to a local LAN 2. Pulling LAN cable on CC1, CC2 changes state to Master & Running. Re-insertin...

Ping using Winbox with interface set to "All" or "ether4" works whilst in terminal mode [admin@MikroTik] > /ping 64.69.34.1 64.69.34.1 64 byte ping: ttl=53 time=34 ms 64.69.34.1 64 byte ping: ttl=53 time=29 ms ... but [admin@MikroTik] > /ping 64.69.34.1 interface=ether1 64.69.34....

Would like confirmation if multiple L2TP tunnels can be established between 2 MT?

Would like confirmation if multiple L2TP tunnels can be established between 2 MT?

I am familiar with MT, however new to scripting. I have taken the time to look through posting in this space and am really impressed how 10 line scripts have been condensed into 1 line. I am trying to develop a script to create 200 client L2TP tunnels between Client-Server and then round robin throu...

For a ML-PPP configuration requiring a prioritized QoS model, looking for confirmation if "mangle pre-routing" and "global-in" is the recommended approach?

I would like understand if there are plans to support ML-PPP Server functionality and if the answer is yes, what is the timeframe?

Hi Cowisp, can you please confirm if you were able to get DHCP option 82 working on MT?

Balance MODE is configured as Round Robin

Router 1 and 2 are directly connected on ether port 3 & 4. On both routers, a bonded interface is created by combining port 3 & 4 and a IP address assigned to the bonded interface. Ping from either router works in this configuration. Switching the bonded interface from physical ports to VLAN...