MikroTik

thembo

thanks again

thembo

wirelessRudy how would one know when their is an interference from others radio's.what should one look for? how would you trace the problems. As concerning my link i have setup my AP on 5240 frequency and its been connected for almost 14hrs hope it keeps up. i had to run a snooper and found that the...

thembo

thanks every much

thembo

thanks for the reply earlier on. i have changed the card in the enclosure to XR5 frequency at 5300,connecting to 24dbi grid antenna. this is set in station mode. my AP is running also on an XR5 connecting to an omni.at first frequency was at 5300 but seem more people are using that so i changed to 5...

thembo

am not using nstreme. client side its on station mode.

signal strength -77dbm
tx signal strength -82dbm
signal to noise 24db
tx/rx ccq 59/43%
Pthroughput 13849 kbps

AP frequency is 5300

thembo

i have a mikrotik client connecting to a mikrotik Ap.first the wireless network was working fine suddenly it keeps diconnecting
every 5 to 10 mins.
the client side is a grid antenna with an R52n card.distance from AP 4km. i get a signal 0f -79 to 80.
what can be the problem?

thanks

thembo

just found out that someone has installed a Vsat in front of the equipment.so i think its the one one causing.will try to move the equipment.using Nstreme do you think it would improve?

thanks

thembo

at the moment i have a grid antenna one side and flat panel the other.the flat panel is 23dbi and grid 24dbi. am using R52N on both sides.

else how can i know that the problem is on this side.what do i have to look for?

thanks

thembo

i have a PtP link which was working fine.i get a signal of -71 on both sides but the problem is that the throughput drops very low a 169kbps and then rises to 16000kbps.i tried changing the wlan card on one side still the same problem tried frequency changing still the same.tx and rx changing from 6...

thembo

i have setup my repeater like this. wireless mode :wds slave ,i have also set it on dynamic wds on bridge1 same ssid ,frequency as main AP.created a bridge where i have added my ether1 and wlan to the port. i have not set any dhcp because i want all dhcp to come from main AP. the problem is that it ...

thembo

need help with configuring a simple repeater for a Hotspot.

thanks

thembo

thanks guys.but practical how many 128k ,256k and 512k can one connect on 3M

thembo

i am running a small ISP of 3M.i have a bandwidth manager.i have tried btest throughput on my backhauls i am getting 3 to 4 Mbps. the problems is am getting slow internet sometimes the browser keep saying server not found.i have asked my providers about the bandwidth quality they say its ok.they hav...

thembo

I have a hotspot which runs fine and then i setup a repeater for the hotspot.signal for hotspot is -69.but the problem is that the repeater only connects to the Hotspot at 11Mbps-SP/11 0r 2Mbps-SP. and then when i connect to the repeater with my laptop its the same 11Mbps or 2Mbps.on the main hotspo...

thembo

i want to create a bridge between two offices.

thanks very much for the response

thembo

i just want to know if a Wlan poynting antenna 2.4ghz would connect to a mikrotik Ap.
i want to know before i buy the poynting antenna.

thanks

thembo

i have a hotspot which gets its pppoe connection through ether1.
it just stopped by itself, the only thing its dialing and disconnecting.i reconfigured the rb and plugged it but
but its still the same.
its connected on a switch which their are backhaul connections also.

can anyone help?

thanks

thembo

the distance is about 2km apart.i have a clear line of sight very clear.

thembo

i have an AP built from RB433AH ,Xr5 cards and 90 degree sector antenna's. i have clients running on Nanostation5. the AP is set: Band -5ghz frequency - 5300 the thing is am able to connect to the AP with signals of signal strength - 80dBm Tx signal strength -72dBm signal to noise -13dB Tx/Rx CCQ 68...

thembo

would someone recommend enabling nstreme on a link which is 2km apart.

thembo

i have a 433rb running as an AP and have a 411rb running as a backhaul.am bridging these two through an 8 port switch cnet. went i ping the 411rb through the poe adapter it runs ok the same with the 433. went i ping the the 433rb through the switch it pings ok but when i connect the 411rb to the swi...

thembo

when you configure ip addresses for different interfaces like 10.1.1.1 for wlan and 10.2.1.1 for ether 2.do you also create a bridge for the interfaces and add them to ports.

thembo

am using a 411rb with an xr5 card on both sides.the spec for the grid 5.4-6 Ghz 30dbi dish antenna 90*70cm parabolic reflector

thanks for the response

thembo

am trying a link 70km with a 30dbi antenna.am able to see the other dish signal in -74 but want connect.am using 5 gzh and frequency 5260.
do these antenna have a specific frequency to run on.

thembo

anyone with an idea of how long would a ptp link using XR5 and 31dbi grid antenna cover.

thembo

am able to get signal strenght of -76 on both sides without nstreme and supported data rates not configured.
but the signal to noise keep flapping from 20 t0 2 db and getting low throughput of about 300kbps.

the grid antenna am using are 29dbi so i want to try with 31dbi.

thembo

let me try and i will get back to you and thanks for the help.

thembo

am not running on nstreme and running on 5ghz and frequency on 5260 wds mode dynamic on bridge1.
data rates is on default

thembo

i have a routerboad 411 cable from injector about 30m. the first time i connected it i could access winbox with no problem.then i started having problems with getting the mac address on winboxloader.if i get the mac and connect ,i get msg 'connection failed port 2#### ' i then shorten the cable ,cou...

thembo

am trying to make a link about 65 to 70 km.am using a 433rb and 411rb, 2xr cards one on each router.am able to see each end but can;t connect for 5min.

am getting -81 to 86. can this be that the distance is too long.

thembo

is it possible to set a wifi network using 2.4ghz freq while the omni is for 5ghz

thembo

my backhole link have just decreased on one side.the other side its ok but the other side has just gone low.
could the problem be on the side which is low.

thembo

this is one of the information from my AP.

signal strength -72
Tx signal strength -71
signal to noise -31dbi
tx/rx ccq 59/20%
p throughput 16953

my AP is running on frequency 5320

thembo

i have a mikrotik AP composed of rb333 350mw card and an omni 12dbi antenna.i have clients using nanostation5. from customer site to AP is about 1km clear line of sight. but when am at customers site and ping the AP the pings go up to 1300ms.form AP the ping are also. my AP is running on frequency 5...

thembo

i have a mikrotik AP/bh composed of an omni antenna 5.7ghz 12dbi ,333rb with 350mw card for the AP. at client site about 1 km i have nanostation5 running and connecting with signal of -64. the problem am facing is when i ping the AP from client side, the pings are so high as 1500ms. opening a web br...

thembo

which are the best frequencies on a mikrokit Ap connecting clients using nano stations.

thembo

am using xr5 minipci cards

thembo

thanks you people

thembo

i have bridge ether 1,2 with wlan but i have not yet connected them on a switch.with the switch its ok i have tried it but i just wanted to know if bridging form the enclosure would do the same.

thembo

i have two mikrotik boards set as APs. one is using v4 so i can connect nanostationm5 clients.
i want to bridge these two using ether 2 on both boards. is this possible.

thembo

i have a bandwith manager which is also my pppoe server.it connected to my AP.if i ping my AP i get about 1ms with no timeouts but if i ping my bandwith manager it pings 1ms but with alot of timeouts. i changed the cables still getting the same. can this be an ethernet problem on my bandwith manager...

thembo

thanks i got it to work.

thembo

ok this is the information.

signal strenght -78
tx signal strength -66
signal to noise 32
tx/rx ccq 76/38
p throughput 16371

this is nano from client connecting to mikrotik ap.

thembo

can some one help me on how to create a vpn using ipsec.step by step using winboxs

thembo

i have an AP on a tower that is fully equiped with different networks for other providers.i had sectors which are 180 degrees but i get customers who connect with a good signal at -75 but the ccQ is very low as 9765kbp and then after about 5 mins it changes to ccq 14387kbp. i then changed the sector...

thembo

can you write me step by step if possible using winbox on configuring the user profile

thembo

i have setup a hotspot but now i want to configure the hotspot user.to create a trail user account for 5 mins.i have already created my login page which asks the client to login as trail for 5 min if they have no hotspot card

thembo

are there other scritping commands for backups apart from /export file=
backing up the whole system.

thembo

i have a 333 rb which is my bandwidth manager which is connecting to my isp.i did a script backup "export file = backup now i have bought a 433 rb which i want to replace.if i copy the backup from the 333 to 433 and restore or import will it restore all the firewall rules, queues and ip address...

thembo

thanks chupaka

thembo

am new to scripting
can some help me with a script so that my router board reboots every 03:00am every day.

Search found 51 matches