MikroTik

diode

Actually all my other routers ignore routes containing the forwarding address set and skip the route from the routing table entirely, they are also running the same router os v7.15.1 (and v6 and Bird). The docu says that when the forwarding address is not reachable for the other router it should gen...

diode

I just want to share my solution of ospf stopping working after upgrade from v6 to v7, so others can find it. The default behavior of sending an LSA generated out of a static route was changed, the forwarding address field before with v6 was 0.0.0.0, with v7 the gateway of the route is inserted in t...

diode

lhg 60 have a fixed rssi now, its not changing anymore. that's ok for already mounted aligned links, but it will make mounting new links more complicated. its obviously only measured once shortly after connecting. the fluktuations are 6.42.6, the line is 6.42.7. the single movement was a reconnect. ...

diode

Hi, I'am a wisp in Austria, running the network with 100% Mikrotik Clients & APs, around 50 Terabyte per month transported. I have Wisps since 2000 ... It's a very noisy environment here, we're using 100% nstreme protocol for all sectors as this gives us the best results. It would be pleasent to...

diode

Having an integrated 5 GHz Backup in LHG 60.

Now I need to mount 2 dishes plus a HEX POE for power ...

diode

Hi, I'd be interested what is the weakest signal that will keep a Mikrotik 60 GHz link online with the lowest modulation and actual firmware. My weakest link is a WAP60 to a LHG60, lenght 763 Meter, RSSI around -69 db. Its planed to possibly have a PTMP scenario later on. ITU Climate Zone H or K (vi...

diode

/in w60g set 0 tx-sector=36

locks tx sector, which might be the center sector

have fun !

diode

Me too ...

I still run the whole ISP on nstreme, its faster here when you have a low count of clients each sektor (4-5 ...).

BR from Vienna !

diode

Are there any mikrotik DFS long time users around ? does the inband monitoring of radar sometimes dedect radars just cause of the damaged pakets a weak link is transmitting on mikrotik ? damaged pakets -> could be radar pulses -> radar dedected, even if not present back in 2003, 2004 exactly that wa...

diode

Hi Mikrotik Gurus,

Is the radar scan active for all channels 100-140 (5500-5700), or just for 120-128 (5600-5640) ? What about channel 52 - 64 ?

will the dfs change also be in 6.36.1 ?

thanks maria !

diode

Hi, after quite some productive communication with the mikrotik support I finally want to announce: Nstreme is now quite stable in noisy environments and works again for outdoor link. Since 6.33 (you need to use the wireless-cm2 paket) its lightning fast again, especially also for single tcp connect...

diode

hi, I have a problem starting nstream to be unusable with ac hardware. I have swapped a RB912 with a netbox5 on a place were nstream was working really good (uptimes of clients ofthen 10-20 days before getting a not polled for too long), now it disconnects ALL clients simultainously every hour or so...

diode

hi,

can anyone explain the different settings, just accessible by winbox

IP, Settings,

difference between

* allow fast path
* allow hw fast path

thanks !!

diode

Hi, It would be fine if the hardware watchdog could check more than one ip adresses, only rebooting if all of them failed. If the checked device is down, the checking device is rebooting even if it doesnt have a problem itself via watchdog. checking more than one device would solve that. thanks, Maria

diode

hi, this is a server housing center, you have to buy the (overlenght) patches from them, and may not place any equpiment somewhere in between. you may even not make a patch yourself, just plugging in a patch cable costs eur 650 each (if cables are present). is there any difference between a "du...

diode

Hi, we do have a 114 m long Cat 7 Ethernet Cable in a server housing center, their room layout is so Sh** that you always get very long connections. That cable worked good with a Routerbord 2011 with gigabit connection for 3 years, now it starts making problems. I wonder which mikrotik products ethe...

diode

Hi, I'd like to be able to specify a source IP for the L2TP Client to use to connect to the destination IP. With a static GRE Tunnel this is possible (field local address). I want to switch from GRE Tunnels to L2TP Tunnel for my internet backup links, and till yet I was ellegantly specifying the bac...

diode

Hi, I had the same issues with upgradeing 5.x -> 6.14, BUT I also had this issue from 6.13 -> 6.14 on one device out of 200. I'm frigthened to upgrade the rest of the 100 devices ... the positive sides: nstreme is extremly fast with the wireless-fp package, it also speeds up nv2 links (but not all)....

diode

Hi,

I do need to set up an indoor WLan for mixed mobile clients. is there any trick to force 5 ghz capable clients to use the 5 ghz clound instead of the 2.4 ghz cloud ?

cisco & lancom systems offer such an option with their accesspoints

greetings, maria

diode

I do have a "default settings" configurations file, which gets to any device before usage, setting nv2 security, security profiles, null routes for bogons, country for the cards, ntp server, smtp server, dns server - so no danger for me. what I found out till yet: 5.14 rocks !!!!!! on a pr...

diode

I'm not having any disconnect problems with nv2, just performance issues. Using nstreme instead solves the performance issuse, but give disconnect problems every few hours.

so I'm just wanting to know which firmware was before introducing the nstreme disconnect issues.

diode

Hi, We're an WISP located in the capital city of Austria. Some sites have a quite congested frequency spectrum, at these sites ofthen NV2 works far worse to the nstreme protokol. With nstreme we ofthen have disconnects (extensive data loss), which we wouldn't have using NV2 (which has way lower CCQ ...

diode

Hi, does the RP filter "loose" setting check the default route or not ? if default route is present (which is nearly always the case at a router), rp filter would be practically disabled. Therefore, the option "Loose Reverse Path Forwarding Ignoring Default Routes" from RFC 3704 ...

diode

hi, the two radio cards will usually interfere each other quite strong. take some tin foil from the kitchen, wrap it to 2 or 4 layers, put it into a platic bag (eg the antistatic bag the 433 was shipped in), and place that between the two radio cards. this works as a reasonably good protection again...

diode

hi, I do have the same issue here with a few clients. firmware version 5.25, 6.2 6.3 6.4 (other not tested) the issue occurs (at least) when winbox is opend, AND the web interface is opened paralelly. while the web interface opening, country will change really ofthen, but I also had the wireless int...

diode

having seperate radios for each provider is the only way to do it for the moment, BUT free channels and space for antennas is not an endless resource.

especially in crowded areas its a huge difference to coorinate 3 oder 6 channels (out of 9, cause 3 cant be used cause of radar reservetion).

diode

any news ?

we, two providers still cant share an ap, as one provider uses encryption as access restriction, and the other one mac authentication via radius ...

greetz from vienna

diode

hi karina ! this is exactly one usual cenario vap is used by me. at the moment you have to configure the network so that nstreme & nv2 are both working, to be able to switch back to nstreme with vap support when you need it. a second scenario is sharing accesspoints between two providers, one pr...

diode

I was JUST quoting the technical details from the mikrotik data sheets on the mikrotik website. so mikrotik says "rb 711" has a worse receiving sensitivity over R52Hn - and I wanted to have that confirmed.

diode

Hi ! I just wanted to have confirmed, that a 711 board really is way less sensitive than a R52Hn card, even if its the same chipset & manufacturer. At 5 GHz R52Hn has a rx senivity of 802.11a: –97 dBm @ 6Mbps to -80 dBm @ 54 Mbps R711-5* has a rx senivity of 802.11a: –92 dBm @ 6Mbps to -76 dBm @...

diode

Hi ! One more issue not beeing solveable without virtual ap: Usually, I have one general SSID on a sender, where customers can roam between if one segment fails, for additional redundancy. Some customers usually will connect to the weaker signal for unknown reason, I do connect these to a sector spe...

diode

Hi ! I'm missing the feature of virtual APs together with NV2. Usually, I have one general SSID on a sender, where customers can roam between if one segment fails, for additiona redundancy. Some customers usually will connect to the weaker signal for unknown reason, I do connect these to a sector sp...

diode

Hi !

I haven't solved it yet - sorry. Perhaps Mikrotik could post a solution ?

Greetings Maria

diode

Hi ! I do have a VLAN Trunk containing tagged packet, but also untagged packets. It's clear how to get the tagged packets to different vlan interfaces and connect them to different bridges. BUT: How do I define an interface getting the untagged pakets from that interface/trunk to a different bridge ...

Search found 34 matches

Re: Static Routes not redistributed with OSPF on v7 - Solution

Static Routes not redistributed with OSPF on v7 - Solution

Re: v6.42.7 [current] is released!

Nstreme improvments wanted

Re: Feature requests

60 GHz minimum RSSI for MCS 0 / staying online

Re: LHG 60G disable beam forming [SOLVED]

Re: Feature request Evolution Nstreme

Re: v6.37rc [release candidate] is released, only one wireless package!

Re: v6.37rc [release candidate] is released, only one wireless package!

Nstreme Working again - Wlan super fast - thank you mikrotik - 6.33

Re: RouterOS v6.27 released

/ip settings fastpath difference

Feaure Request: Watchdog to watch multiple IP addresses

Re: Overlenght Ethernet Cable - Which Product works best ?

Overlenght Ethernet Cable - Which Product works best ?

l2TP Client binding to ip

Re: v6.14 released

Indoor Wireless - move clients automatically to 5 GHz

Re: PtM Links - which firmware for nstreme

Re: PtM Links - which firmware for nstreme

PtM Links - which firmware for nstreme

RP Filter Loose Reverse Path Forwarding Ignoring Default Rou

Re: How to optimize AP performance

Re: ROS 6.2 and 6.3 +Winbox + Quickset = self country change

Re: Virtual AP and NV2

Re: Virtual AP and NV2

Re: Virtual AP and NV2

Re: R52Hn & RB711-5HnD - Big difference in rx sensivity

R52Hn & RB711-5HnD - Big difference in rx sensivity

Re: Virtual AP and NV2

NV2 and virtual APs

Re: VLAN Truck, bridging untagged packets

VLAN Truck, bridging untagged packets