MikroTik

Nanflexal

hi GUys, I already reset my configuration and free internet on youtube.com has been fix however after i reset my configuration my radius is not responding, same radius config. Im using 7.16.1 XXXXXX (150.100.103.22): login failed: RADIUS server is not responding I cant downgrade to lower version. Qu...

Nanflexal

it's not working. the problem remain. im routerOS 7.16.

I will reset the config of my router and try again. I will post the result.

thansk a lot.

Nanflexal

停用 mangle 內的規則就正常了這問題兩年前就反映了無解!!! 官方把問題歸咎於PCC,但我一開始就說了與make connection有關 Disable the rules in mangle and it will be normal This problem was reported two years ago and there is no solution!!! The official blames the problem on PCC, but I said it was related to make connection from the beginning....

Nanflexal

Guys, Here is the export config from my router. Regards, Alex # 2024-10-06 19:16:16 by RouterOS 7.16 # software id = K708-7U56 # # model = CCR2004-16G-2S+ # serial number = HAT07EQ7PC2 /interface ethernet set [ find default-name=ether7 ] name=HOTSPOT set [ find default-name=ether3 ] name=LAN set [ f...

Nanflexal

then it is not possible to go to YouTube if the authentication has not occurred. send an export of /ip hotspot and /usermanager if you use it. Make sure that before the login it does not ping the usual 8.8.8.8 and 1.1.1.1. maybe on YouTube it goes in offline mode. Thanks for your input and you're r...

Nanflexal

Guys,

There is no wall garden and i use external radius for hotpot. please see attachment

thanks for your input.

Regards,
Alex

Nanflexal

HI All, Guys, i setup hotspot in CCR2004-16G-2S+ and hotspot is working fine except one problem. My hotspot is configure to authenticate user before having internet access by using username and password. My problem, when someone connect to my hotspot with the SSID: XXXXX.com the user didn't input us...

Nanflexal

How about Mikrotik OLT, any update?

Nanflexal

HI All,

I have problem in my RB4011, this router take 4 Minutes or more to authenticate PPOE user and I'm using 7.1.1 RouterOS. anyone encounter this issue?

Regards,
Alex

Nanflexal

ANy news about OLT?

Nanflexal

Another problem in V7.5 User manager. when you create voucher then you select same password as username, User Manager will generate other password not the same as username. this is misleading.

we can export only 1 voucher in .html, csv and xml format.

Nanflexal

This is not problem in v7.5 i found the issue. when you create voucher and depending on how you defend prefix username and if you set 4 length password User manager will generate password MINUS prefix Username. another problem of this V7.5 is that you can't export multiple voucher in html or . csv o...

Nanflexal

HI Guys, I'm just testing this User manager 7.5 but after successful configuration and after i created voucher in usermanager, Password is invalid. during creation of voucher, in, "Password Length: same as Username" but if i login to hotspot using that account password is invalid, i have t...

Nanflexal

Any change of having OLT? please give us update regarding this.

regards,
Alex

Nanflexal

any word about GPON or EPON?

Nanflexal

How to block mac address completely without giving them internet access?

Regards,
Alex

Nanflexal

HI All,
guys, i have missing profile problem in user manager. my 1 hour voucher has no profile at the moment. my question is, can i move this voucher to a new profile via CLI.

regards,
Alex

Nanflexal

Hi All,

can we use single mode module in FiberBox?

Regards,
Alex

Nanflexal

You've got the wrong forum it seems.

maybe but my router is miktrotik.

Nanflexal

hi guys

i setup small router at home without toughtswitch & i use un-manage switch and still my VLAN is not working and cannot receive ip from VLAN dhcp.

nanobeam is in router mode with vlan enable connected to litebeam ac sector. libtebeam ac sector has no vlan tag and in bridge mode.

Nanflexal

Guys, can you tell me what is wrong with my setup. LAN ip is working with internet but VLAN has no internet and cant get ip from VLAN dhcp. if this config is wrong, can you help me fix it. thanks in advance. ------------------------- /interface ethernet set [ find default-name=ether3 ] name=LAN set ...

Nanflexal

see below. thanks

Nanflexal

out of interest, how are you connecting to your ISP? fiber modem connect via PPOE then i enable local DHCP server and i use static local ip to connect. The ping times to your gateway are 0ms...very quick! Are you sure the gateway IP is correct? anyway, my problem is fixed now. the problem is in my ...

Nanflexal

i tried to use dhcp client but i cant get ip my local dhcp server.

Nanflexal

still no internet. [admin@MikroTik] > export # jan/02/1970 00:01:53 by RouterOS 6.34.6 # software id = CN5P-ZY8J # /interface ethernet set [ find default-name=ether2 ] name=LAN set [ find default-name=ether3 ] name=WAN /ip address add address=192.168.10.2/24 interface=WAN network=192.168.10.0 add ad...

Nanflexal

Hello,

can you ping your gateway?

yes. i can ping gateway 192.168.10.1 but to internet connection.

Nanflexal

guys, i trying to configure my router but its not working. no internet connection. any idea? [admin@MikroTik] > export # jan/02/1970 00:14:03 by RouterOS 6.29.1 # software id = CN5P-ZY8J # /interface ethernet set [ find default-name=ether2 ] name=LAN set [ find default-name=ether5 ] name=WAN /ip poo...

Nanflexal

Guys,

do you have idea on how to setup TWO WAN in load balancing setup and 4 LAN.

my setup:

WAN1: 121.X.X.X
WAN2: 122.X.X.X
LAN1: 10.10.10.X (DHCP enable)
LAN2: 10.10.11.X (VLAN10)
LAN3: 10.10.12.X (VLAN20)
LAN4: 10.10.13.X (VLAN30)

Nanflexal

Hi we are a small WISP with 120-150 users under mikrotik+ubiquiti is working. We want to invest in more stuff because we need to grow. Our requirement we are searching is, what others WISP are using to save bandwidth caching youtube and site like, fb, u know the type of portals that eat your bandwi...

Nanflexal

I running tagged in mikrotik sxt ethernet - > Ubnt switch and untagged from ubnt switch to user.

Thank you. it's clear to me now.

Nanflexal

Iam running an SXT whit several vlan on the ethernet port that are connected to an ubiquity switch whit no problems. Thank you your reply. I have a question, Do you enable VLAN feature in miktrotik router my setup is this: Miktrotik router > Fast ethernet > ptp link > faster ethernet> Airmax omni> ...

Nanflexal

Guys, I'm about to implement VLAN in my network and i'm looking for advice or suggestion for my setup. my first question is, is there compability issue if i enable VLAN feature in miktrotik router and Loco M2 or NanoStation M2 VLAN feature in customer side and will it work? see my diagram below. htt...

Nanflexal

Please describe which IP address bound to what interfaces. Than double check it yourself before bumping on submit. Maybe you found that NO address bound to any VLAN interface. thank you for your reply. here is the interface and IP for WAN. I just need to figure out if VLAN in my 6 WAN link can be u...

Nanflexal

Nanflexal: Since IP addresses are assigned to WAN interface (physical interface) and not to VLAN, why do you expect so see any traffic on VLAN ? Hello, i'm not sure if VLAN is working because i didn't see TX and RX traffic on VLAN. WAN1 VLAN ID is 100 and WAN2 VLAN ID is 101, I just want to know if...

Nanflexal

Guys, I have miktrotik router and working fine and use in my load balancing. i'm planning to add another line with 10 MB down and 10 UP called ISP4. (see image below). my question is, can we enable VLAN in my load balancing router / setup while the router provide load balancing for my client. ISP1, ...

Nanflexal

Guys, I'm trying to setup VLAN as show in the picture but i'm not sure if VLAN is working because there is no TX/RX traffic in miktrotik router for VLAN interface. VLAN ID for WAN1 is 100 and VLAN ID for WAN2 is 101. what is wrong with this setup. Router config: /ip address add address=192.168.88.10...

Nanflexal

I already have 2 Routerboards running with load balancing enabled. Now I have a new Project at a different location, but one of there Wan Providers only offers dynamic Ip Adresses. Is it possible to have routeros to loadbalance with a wan connection only offering dynamic IP? You can do with a scrip...

Nanflexal

yes, you can. VLAN interfaces just like wired interface from view of firewalling.

thanks and i forgot to mention. No VLAN in ISP1, ISP2 and ISP3 only ISP4 will have VLAN enable. so all ISP1, ISP2 and ISP3 is my default gateway for my residential customer.

Thanks

Nanflexal

Guys, I have miktrotik router and working fine and use in my load balancing. i'm planning to add another line with 10 MB down and 10 UP called ISP4. (see image below). my question is, can we enable VLAN in my load balancing router / setup while the router provide load balancing for my client. ISP1, ...

Nanflexal

Alright. perhaps the term i use here is not adequate for my setup however my plan is simple. at the moment, If i run speedtest via speedtest.net i got 15 or 18 mb each DSL line but let's assume we got 10 MB download and 3 MB upload here. now after your setup and i run speedtest.net we should get 30 ...

Nanflexal

Guys, I'm looking for someone who can combine my 3 DSL line into one, each DSL is 10 MB download and 1 MB upload so if we combine this 3 DSL it will be 30 MB download and 3 MB upload. this can be done without asking ISP side because it's so hard to contact them. i have a friend who have this setup ...

Nanflexal

Guys, I'm looking for someone who can combine my 3 DSL line into one, each DSL is 10 MB download and 1 MB upload so if we combine this 3 DSL it will be 30 MB download and 3 MB upload. this can be done without asking ISP side because it's so hard to contact them. i have a friend who have this setup b...

Nanflexal

how do i export my config?

Nanflexal

Guys, i'm new to miktrotik and i need help about port forwarding. WAN IP: x.x.x.x Router: 10.10.10.254 Rocket M5 radio: 10.10.10.17 how do i forward traffic from WAN IP to my rocket M5 ip: 10.10.10.17 i'm trying to make this thing work but it's not working the config: /ip firewall nat add chain=dstn...

Nanflexal

http://www.sknox.com we are manufacturing whitespace wireless cards for MikroTik devices. currently operating them under an experimental license. i'd be interested in writing third party code to import as a package but we are unable to do that... so our management systems are being developed sepera...

Nanflexal

I'm interested in this technology and can't wait to test it.

can you tell me what equipment we need to implement TVWS? and how much it cost?

thanks

Nanflexal

Hello Guy, can we disconnect user automatically during idle time in user manager? I have customer who bough 5 hour internet access but after 1 day his / her account run out of time because he / she forgot to logout. in that 5 hour, he / she use 1 hour and 30 minutes so he / she still have 3 hour and...

Nanflexal

if your hotspot properly config, it will automatically redirect you to hotspot login page. there is something wrong with your config.

Please post your hotspot config.

Nanflexal

Please send me a copy. nanflexal@gmail.com

thank you very much.

Nanflexal

Hello Guys, I wan to implement VLAN on network but i don't have experience in miktrotik using VLAN. I would really appreciate if someone can help me give some example on how to implement VLAN base of my diagram. see attachment. I should be able to connect from router 1 to router 5 and vice versa and...

Nanflexal

Guys,

I plan to create a promo, let say $10 for unlimited internet valid for 3 day from the first use. or any other similar script.

Thanks
Alex

Nanflexal

you can do this with webproxy and address-list.

can you give me an example or guide on how to do.

Thanks in advance

Nanflexal

can we modify this to send email is one WAN interface is down.

thanks

Nanflexal

Guys,

is there way to redirect user to specific url via ppoe. I'm running 3 DSL line and configure as load balancing & i want all my customer to redirect to specific url

Thanks

Nanflexal

first of all upgrade your ROS verison then verify if the Interface with name Local exists in /interface print thanks. I manage to fix it but i'm having other issue right now. i have 3 dsl line with 10 Mb each line and it's being configure for load balancing but i'm having problem with PPOE Server, ...

Nanflexal

Guys, i'm trying to make load balancing but i'm stuck with message: [admin@MikroTik] /ip address> add address=1.1.1.50/24 network=1.1.1.0 broadcast= 1.1.1.255 interface=Local comment="" \ \... disabled=no input does not match any value of interface MikroTik RouterOS 4.11 (c) 1999-2010 http...

Nanflexal

of course but i think it's not policy ip-base routing.

anyway, i found a sample policy ip-base routing but it's only 2 dsl line.

Nanflexal

Guys, could you please take a look at this config, i found it from other site and i make some modification to suit my need. I've like to use PCC / Policy base routing. the 3 DSL line will be use by three (3) group namely: 1. Residential - 10 Mbit DSL line 1 2. School - 10 Mbit DSL line 2 3. Business...

Nanflexal

Guys,

can you share some of your config on 8 static DSL line. until now i'm struggle to get internet bandwidth so i will build a new backhaul to feed my network.

if anyone of you has a config for 8 static dsl line and be it PPOE or hotspot please share it guys.

thank you so much.

Nanflexal

I'm probably missing something here, but why do you need mpls and pppoe? Unless you're going to run vpls or true end to end mpls I don't think you need any of it for pppoe. I'm just trying to make my network better, be it VPLS or MPLS and you're right, ppoe does not need MPLS. if you have true end ...

Nanflexal

Guys, I don't have experience in deploying MPLS and PPOE so i need your help about how to inter-connect does site using MPLS. I need help about configuration in RB450G to establish MPLS. Site A Configuration /system identity set name=Site A # add loopback interface /interface bridge add name=loopbac...

Nanflexal

could someone help.

thanks

Nanflexal

can't login to the system. perhaps in-correct credential.

Nanflexal

Guys,

is there a way we can redirect non-paying customer to specific page via hotspot because instead of seeing "page cannot be display in customer side browser" they will be redirected to suspended.htm

Thanks in advance

Nanflexal

Guys, Please check if my config is correct for 4 ADSL line and load balancing setup. Thanks in Advance @ Alex / ip firewall mangle add chain=input in-interface=pppoe-out1 action=mark-connection new-connection-mark=wan1_conn add chain=input in-interface=pppoe-out2 action=mark-connection new-connectio...

Nanflexal

For what kind of users? PPPoE hotspot, . . . ? I see my ISP use this for PPPoE service. when my credit finish, instead of block me to authenticate, let me to connect but redirect me to a page which tells your credit has been finished. "PAY". :) i'm using hotspot and DHCP and default DHCP ...

Nanflexal

Guys,

is there a way to redirect suspended account / customer to specific page. (e.g. www.dnsname.com/suspended.html)

Thanks in advance.

Nanflexal

if budget is not a problem then use solar power and use dc to dc conversion for your radios and network appliances.

you can find some dc to dc poe injector here and some poe device.
http://tyconpower.com/products/POE.htm

Nanflexal

thanks a lot.

Nanflexal

guys, i have one more question. how do i make Lan Port 3,4,5 and 6 be able to ping each other? and how do i enable hotspot on Port 3,4,5,6? please check this config for hotspot. Hotspot Config on Lan Port 3 [admin@MikroTik] /ip hotspot> setup Select interface to run HotSpot on hotspot interface: eth...

Nanflexal

No. You only need that NAT line once. Repeating it four times doesn't make any sense.

i see.

i have edited my reply above. thank you very much for your help.

I will test this config next week.

Nanflexal

so it would look like this. /interface enable ether1,ether2,ether3,ether4,ether5,ether6,ether7,ether8,ether9 ISP 1 /ip dhcp-client add interface=ether1 disabled=no Lan Port 3: /ip address add address=10.10.1.1/24 interface=ether3 Lan Port 4: /ip address add address=10.10.2.1/24 interface=ether4 Lan ...

Nanflexal

Guys, please check this config. thanks /interface enable ether1,ether2,ether3,ether4,ether5,ether6,ether7,ether8,ether9 ISP 1 /ip dhcp-client add interface=ether1 disabled=no Lan Port 3: /ip address add address=10.10.1.1/24 interface=ether3 /ip firewall nat add chain=srcnat src-address=10.10.1.0/24 ...

Nanflexal

Guys, i'm using RB493ah right now using bridge mode. now i want to configure port 3,4 and 5, 6 but Port 5 & 6 will be use later. I want to configure NAT on port 3,4,5,6 with DHCP LAN Port 3: 10.10.1.1 / 255.255.255.0 LAN Port 4: 10.10.2.1 / 255.255.255.0 LAN Port 5: 10.10.3.1 / 255.255.255.0 LAN...

Nanflexal

The RB units have no battery backed system clock. You must set NTP to reset the correct time after a reboot.
/system ntp client

hello surfertim, what is the command to enable NTP to reset the correct time after a reboot.

thanks

Nanflexal

Guys,

If i reboot my RB493AH the system clock reset back to 1917, (something like that) this happen everytime i reboot my router.

Thanks

Nanflexal

Guys, I talk to my ISP provider, they said they support MLPPOE this mean i can use bonded feature in my RB493AH but i need help about bonded config. I want to bonded my 3 ADSL first before implementing load balancing. if my ISP don't Support bonded "MLPPOE". (Multi Line procotol) then i wi...

Nanflexal

i have the same purpose too on my RB493AH but right now i have one network but later i will add another one.

but i want to create anaccount that will enable them to login to any of my hotspot / network.

Nanflexal

Hi, Hope this helps... [xxxxxx@xxx.xxx.xx] /ip firewall mangle> print Flags: X - disabled, I - invalid, D - dynamic 2 chain=prerouting action=jump jump-target=p2p-service layer7-protocol=DIRECTCONNECT 3 chain=prerouting action=jump jump-target=p2p-service p2p=all-p2p dst-address-list=!dns-servers 4...

Nanflexal

thanks, let say i have 5 Workstation inside behind router, this workstation will not ask hotspot login credential. is this correct? Thanks If you configure your dlink router as dhcp client(WAN port), and your 3 computers is getting ip address from the same dlink router(as DHCP server-Lan port), the...

Nanflexal

If you use ip-binding, the login requirement is bypassed. I use the mac address of the equipment to bypass. That way you can use the 1:1 nat. If you have the hotspot 1:1 nat disabled, you can use the ip address. /ip hotspot ip-binding add mac-address=xx:xx:xx:xx:xx:xx type=bypassed I see, but let s...

Nanflexal

if you don't want to use ip binding, then enable mac address authentication in your hotspot server profile and create user with the mac address of your dlink router under users. thanks, let say i have 5 Worksttaion inside behind router, this workstation will not ask hotspot login credential. is thi...

Nanflexal

Guys, I have single network with IP: 10.10.10.X and hotspot was enable on this IP, is there a way to bypass hotspot login when using external router like dlink or tplink. My point is, let the external router dial and connect to my network but the computer inside the external router should not ask h...

Nanflexal

That is my config yes, Or to be more accurate the basics of the setup. You will have to adjust it to your setup. Can you be more specific about what confuses you? can you provide screen shot of this part. Go to the Firewall Mangle. Create a new rule Set it as a prerouting chain and set L7 according...

Nanflexal

Guys, I have single network with IP: 10.10.10.X and hotspot was enable on this IP, is there a way to bypass hotspot login when using external router like dlink or tplink. My point is, let the external router dial and connect to my network but the computer inside the external router should not ask ho...

Nanflexal

Here is the login page I've been developing recently for use at my companies sites. We use a full portal-like web site that customers can manage all aspects of their account from.
login.PNG

I'm planning to create similar to this template or hire someone to do the same.

Nanflexal

thanks for your reply. i keep reading your load balancing setup over 6 ADSL line but right now, i don't have VOIP and my problem right now is that assigning IP to my LAN Interface namely: ether1, ether2,ether3 and ether4. please take a look, I've like the load balancing guide there because it's too ...

Nanflexal

Just ask and I'll post my 6 ADSL setup with national/international split, combining PCC for 'sensitive' (read 443) ports & address list of IPs(normal sites that doesn't like Nth load balancing) with Nth for super fast multi-session downloads from the rest. for free. lol hello Ekkas, can you tak...

Nanflexal

I'm just thinking on how i can use this config to my situation. LAN: ether1: 10.10.10.254 ether2: 10.10.0.254 ether3: 10.10.1.254 ether4: 10.10.2.254 Load Balancing Diagram http://imageshack.us/photo/my-images/824/loadbalancing.jpg WAN Dialer 1. / interface pppoe-client add interface=ether0 user=&qu...

Nanflexal

Guys, I'm using RB493AH and i have existing 1 DSL at the moment but i plan to add 1 or 2 DSL line this june so i just want to ask your help setting up Load Balancing for my RB493AH. both DSL account use PPOE and how to enable NAT on port ether3 because ether0 and ether8 & ether9 will be use as W...

Nanflexal

Thanks, I will download this tutorial.

Nanflexal

TKITFrank is this your config? Here is the config DNS /ip dns static add address=127.0.0.1 disabled=no name=router.utorrent.com ttl=1d add address=127.0.0.1 disabled=no name=dht.vuze.com ttl=1d add address=127.0.0.1 disabled=no name=vrpc.vuze.com ttl=1d add address=127.0.0.1 disabled=no name=vzrpx02...

Nanflexal

OMG. the file is too big, could someone post QOS on this tutorial.

thanks

Nanflexal

watch this http://www.tiktube.com/index.php?video= ... xClIoEKDH=

Thanks, i will check it.

Nanflexal

Guys,

I'm new to this QOS so im gonna need some help setting up my QOS on my RB493AH, My LAN IP & GW is: 10.10.10.254,

Priority is:

1 Email
2 Chat. e.g ym,skye and etc.
3 Etc
8 Youtube.com

Any help will be greatly appreciated.

Nanflexal

Thank you. Bonded is not my option right now and i will to ask my provider if they support multi link ppoe.

I will go for Load Balancing, could someone help me the config for my RB493AH.

thanks

Nanflexal

My repeater.

Solar Panel

Picture taken from, Sagrada Bulan Sorsogon, Philippines

Nanflexal

Hi,

Have a look at this topic.
http://forum.mikrotik.com/viewtopic.php?t=21178

Thanks for the link but too many example / firewall rules. which once can you recommend?

thanks

Nanflexal

Guys, I'm using RB493AH and i have existing 1 DSL at the moment but i plan to add another 1 DSL this june so i just want to ask your help setting up DUAL WAN (BONDED) for my RB493AH. both DSL account use PPOE and how to enable NAT on port ether3 because ether1 and ether9 will be use as WAN port. eth...

Nanflexal

Guys,

how do i block p2p traffic on my RB493AH? i have very limited internet at the moment so i want to filter or block p2p traffic while i wait my dedicated internet line.

Could someone tell me where to download regexp and miktrotik firewall rules to block p2p traffic.

Thanks

Nanflexal

Sorry for using the term "Hang"

anyway, When issue that command the router become un-responsive so you need to reboot the router to gain access again.

ether1 act as WAN. my hotspot is working fine now but i bridge ether2-ether9

Nanflexal

I use the config below and firewall are blocking ftp and ssh so i reset the config of my router & create a new one and it work but without firewall rules. / ip firewall filter add chain=input connection-state=established comment="Accept established connections" add chain=input connecti...

Nanflexal

You are trying to connect to the router with a ftp client on a computer? Which one are you using? Use the ip address of the interface, the user and password. It should connect somewhat like ssh or telnet. Do you have any rules in "/ip firewall filter" that could block it? no, i dont have ...

Nanflexal

Guys, i'm trying to connect thru ftp in my RB493AH but i can't connect. could someone help me.

thanks

Nanflexal

I think the site is down during my testing. it's working now.

Thanks

Nanflexal

Guys,

I manage to setup my hotspot and it's work fine however i can't download any file. please help enable download of certain file like, .rar, .exe, .zip, .mp4, .mp3 and etc.

thanks

Nanflexal

/interface ethernet set ether3,ether4,ether5,ether6,ether7,ether8,ether9 master-port=ether2

not working. if isue this command the router hang.

Nanflexal

Guys,

could someone help me create switch on RB493AH, ethe1 will act as WAN port and ether2-ether9 will act as switch.

how do i make this.

thanks

Nanflexal

because i can't figure out how to enable NAT on ether2-ether9. it is my experimental.

thanks

Nanflexal

opps, sorry guys. duplicate post: http://forum.mikrotik.com/viewtopic.php?f=10&t=46205

Nanflexal

guys, could someone tell me what is wrong with this config. this work while the router in ON but when you reboot the server. NAT on ether2 - ether9 is not working. /interface enable ether1,ether2,ether3,ether4,ether5,ether6,ether7,ether8,ether8,ether9 /ip dhcp-client add interface=ether1 disabled=no...

Nanflexal

I manage to work this out by issuing the command. ether2 t ether9 is now working fine. /ip address add address=10.10.10.254/24 interface=ether1 /ip firewall nat add chain=srcnat src-address=10.10.10.0/24 action=masquerade and i create a bridge & port. Thanks this setup work but when you reboot ...

Nanflexal

I manage to work this out by issuing the command. ether2 t ether9 is now working fine.

/ip address add address=10.10.10.254/24 interface=ether1
/ip firewall nat add chain=srcnat src-address=10.10.10.0/24 action=masquerade

and i create a bridge & port.

Thanks

Nanflexal

You need to nat traffic that goes out of ether1 (your wan interface). http://wiki.mikrotik.com/wiki/Manual:IP/Firewall/NAT#Source_NAT Then you need to bridge or switch together eth2-eth9 and run dhcp server on bridge interface. http://wiki.mikrotik.com/wiki/Manual:IP/DHCP_Server#Basic_examples can ...

Nanflexal

thanks for your reply mrz.

I forgot to mention that i will not use DHCP on my network.

I just need to enable NAT from ether2 to ether9 and i should be able to ping device attach on ether2 to ether9,

Thanks

Nanflexal

Guys, I got RB493AH and i want to enable NAT on ether2 to ether9 because ether1 will act as WAN port. I won't use switch that's why i want to enable NAT on ether2 to ether9. im using dynamic IP (DHCP) from my ISP. i will use this IP as gateway "10.10.10.254" and i should be able to ping de...

Nanflexal

Guys,

could someone help me create Postpaid and Prepaid account on my RB493AH.

Postpaid means, they have fix monthly fee
Prepaid means, Pay per hour / per minutes or custom plan as long as prepaid setup.

Thanks guys.

@ Alex

Nanflexal

Thanks, i can't send private message here. I just need to enable NAT on ether2 to ether9 because ether1 will act as WAN port and i should be able to ping all that IP. DSL Modem (dnynamic IP) ether1: 10.10.10.254 (Gateway) Private LAN IP: ether2: 10.10.10.1 ether3: 10.10.10.2 ether4: 10.10.10.3 ether...

Nanflexal

Guys, could someone help me configure my RB493AH, I'm new to this router http://www.adamos.org/images/bon-ot.JPG I want to change the IP address of my RB493Ah to 10.10.10.254 & netmask 255.255.254.0 and use eth1 as WAN and enable NAT but disable DHCP. please help me configure my router base on t...

Nanflexal

Thanks ojsa and can i have the default config of RB750G? also it is possible to create user group in RB493AH called "Postpaid" & "Prepaid", Postpaid will have a monthly fee while Prepaid use prepaid card to browse the internet.

Thanks

Nanflexal

Guys,

I need help in configuring my RB493AH,

I need to change the IP of my RB493AH to 10.10.10.254 netmask 255.255.254.0 &
i need to enable NAT but no DHCP enable & i want to act eth0 as WAN port.

Please help configure may RB493AH

Thanks

Nanflexal

anyone use RB750 to manage port range and is this manage switch?

Nanflexal

after some consideration and presentation of technicals staff from reseller of qno product in the philippines, I will use their Load Balancer appliances with 4 WAN port, This load balancer has a fantastic features, you can make fail over or load balancing or use your 3 ISP at the same time. some fea...

Nanflexal

Guys, i have another question, i was thinking of my 6 ISP with 1 Mbps speed in matnog, so i would like to know if my 6 ISP can reach in Bon-ot big?

Thanks in advance for your reply.

@ Alex

Nanflexal

guys, do you have a guide on how to configure RB750?

My setup would be:
Dual wan Link Router.
internet(1,2)----> dlink1
internet(3,4)----> dlink2 ------>RB750 ------>APs
internet(5,6)----> dlink3

Thanks in advance.

@ Alex

Nanflexal

Price: US $2,145.00
Condition: Refurbished
good luck

I can't affor to buy it this time. maybe later once my network become operational.

anyway, I will try to Bond 4 or 6 ISP using Ubuntu. Thanks

Nanflexal

You may look for the Big 5 Load balancer...

thank your input angboontiong, can you give me the exact model or link to that product?

Thanks
Alex

Nanflexal

Congrat for the hardwork. it's amazing.

I have the same project. anyway, I want to build my own WISP somewhere in the philippines, I plan to cover all island in our place which Telco can't provide internet access.

here is my thread:
http://forum.mikrotik.com/viewtopic.php?f=7&t=34957

Thanks

Nanflexal

how about english language in indonesia or Philippines?

Nanflexal

Hello guys, I'm new to mikrotic product so i need help about configuring RB750, I need help to combine 6 ISP & 3 dual wan dlink router and RB750. Dual wan Link Router. internet(1,2)----> dlink1 internet(3,4)----> dlink2 ------>RB750 ------>APs internet(5,6)----> dlink3 I can't find affordable ro...

Search found 130 matches