Hi, We have several CCR1072`s where we also route multicast over via pim, after increasing bandwidth to 15mbit per stream we are getting random continuity / pixelation errors. Now we traced the problem to one of our CCR`s which runs PIM and routes the multicast traffic, so we replaced the device wit...

how about vlan priority? https://wiki.mikrotik.com/wiki/Manual:WMM#How_to_set_priority + shaping vlan2 to 95% of bandwidth Could not get this to work, but fixed it in another way.. On VLAN 1 = 80% limit, VLAN2 can have 100% of the entire connection. Seems to work OK, normally VLAN2 just uses 10/15%...

Well, VLANs are Layer 2 - I don't believe you can "guarantee" layer 3 capacity. If you have a 100mbps interface, give vlan1 95mbps, and vlan2 5mbps via simple queues. More than that, I don't think you can do. Ok, I also have control over the Layer 3 subnets (both VLAN`s have IP addresses ...

Anav: Good question, I believe want you want to look into is queues! Martinclaro: To do that, you will need to do load-balancing + failover (search for PCC or ECMP). This I know, I already have several working simple queues and queue tree's in my infrastructure that work perfectly; But how to make a...

Hi, I`m a little bit stuck, here`s my scenario; I have 1 interface, 100mbit up and down. Over this interface I have 2 vlans running, 55 and 57. Now from the total link I need to prioritize vlan 57 for about 95% of total bandwidth up and down (only when used). What is the best approach here? Maybe if...

I`m missing the forward rule in the firewall, I don`t know the command out of my head but it should be

Firewall -> add rule -> forward -> DST-Adress = 224.0.0.0/4 -> -> in interface / out interface -> action accept or passthrough..

If someone runs into the same issue, I have found the problem;

On one SFP+ interface flow control was set on auto, after setting flow control on OFF the problem was gone..

I just checked, there is no loadbalancer active on that link

Hi all, 1st: CCR1072 firmware 6.44.2 2nd: CCR1072 firmware 6.44.3 I have 2 CCR1072 routers in 2 different datacenters, both routers are connected with eachother via a 10GB dedicated link.. Now there are UDP streams going over this link but the packets are one-way out-of-order. When using iperf (on 2...

Removed the bridge..
Problem solved..

Thanks!

Hi everbody, I have a problem with 2 mikrotiks, the 2011UiAS and the 3011UiAS. We have 2 datacenters that is connected with an NDIX, previously we used a sophos UTM to bridge the datacenters but we wanted to lower the load on the Sophos UTM. So we have placed mikrotiks instead with the routing table...

it`s working..
thanks for you`re advice..

what i did was add a static value of 0.001, i won`t show up on the chart but it will show the probe as "UP".

Sorry, the ip address needs to be in quotes. oid("1.3.6.1.4.1.1768.100.70.10.2.1.2.1", 10, 5, "81.28.86.107") It works, thanks! one more thing, when the value of the "SIP_TOTAL" is 0, i`m getting that the probe is down.. i`m using: available: SIP_TOTAL() > 0 Error: if(...

hmm it doesn`t seem to work..

i made a function called: SIPCALL1
the error i`m getting = oid("1.3.6.1.4.1.1768.100.70.10.2.1.2.1", 10, 5, 81.28.86.107)

with the function SIP_TOTAL i`m getting a parse failed error.

Hi,,

i`ve made several data-sources from different devices, now i want to add up the numbers (example : 1+2+6 = 9) of these datasources and show them in a chart.
Is this possible?

if so, then what code should i use?

probes/functions for HP laserjet printers which warns when the specified toner reaches 15% or less: function: name: toner1 code: string_substring(oid("1.3.6.1.2.1.43.11.1.1.9.1.1")/oid("1.3.6.1.2.1.43.11.1.1.8.1.1"),0,4)*100 probe: name: HP Printer toner 1 available: toner1() err...

Hello, i`m just new to the dude and have a question regarding SSH probe.. on the remote side there`s a linux machine and i need some kind of script to check if an external device there is working. if i log in the linux device with putty i can isue the following command to check the external device: ...