MikroTik

moly

We solved the problem by replacing the technology by Ubiquity Wave.
Nothing flaps, nothing disconnects, and latency has dropped significantly.

moly

And one more problem what is happening to us. Observed on multiple versions including 7.11. For some clients, the speed gets stuck at 385Mbps - MCS0. They do not display RSSI, TX sector, RX sector and TX sector info. After disconnecting and connecting the client, everything is ok again. It doesn't h...

moly

Tried another frequency and it keeps happening. We will have to replace it with the RBwAPG-60ad-A. People are upset about the constant outages.

moly

AP is CubeG-5ac60ay-SA , all client have 7.11beta2.
Signal level : -53,-51,-57 , all MCS 8 , distace : 307m,284m,330m. Freq 58320MHz.

moly

Hi, i try 7.11b2, problem still here. 3x nRay client. Compared to version 7.10, the client is no longer permanently disconnected until the AP is restarted. In version 7.10, the client was sometimes permanently disconnected. LOG : 06-25 09:23:09 interface,info wlan60-station-1: link down 06-25 09:23:...

moly

A strange thing happened to me. I tried to turn on "Isolate stations" on the AP (CubeSA Pro) and this stopped happening with high traffic. Then I turned off "Isolate stations" again and it still doesn't happen. So far, I have tried it on a test in the lab and on one operating tra...

moly

I try 7.8 and the problem is still there. (1x AP Pro and 2x AD client or 1x AP Pro and 1x AD and 1x Pro client) I observed that when the traffic on the clients is below 200M, it does not happen, or only at a minimum. Once the traffic exceeds 250M, it starts to drop in a big way. Is anyone from Mikor...

moly

AP Configuration : /interface bridge add name=bridge_102 protocol-mode=none add name=bridge_118 protocol-mode=none /interface w60g set [ find ] disabled=no frequency=62640 isolate-stations=no name=wlan60-1 \ ssid=xxxxxx /interface vlan add comment=10.1.137.0/24 interface=ether1 name=vlan102 vlan-id=...

moly

Hi, I have CubeSA 60Pro. If I have only one clinet ( RBLHGG-60ad ), all was ok. Now I have two client RBLHGG-60ad and CubeG-5ac60ay and sometime booth client drop and reconnect. It seems to do it under higher load. If I try Bandwidth test from AP to client, after some second both client drop and rec...

moly

Hi,
will be able to use half channel in 60GHz?
Will be possible to use 1.08GHz or 540MHz channel width?
Thanx

moly

Hi,
I have question about DNS cache performance.
How much DNS query per second can handle ROS?
Its some SW limitation in ROS or can use all resources up to 100% CPU?
And can use only one CPU or all CPUs in system?

Thanx for answer.

Moly

moly

Hi, I have problem with SFP DDM monitoring.
I try on CRS112-8G-4S and in version 6.35.4 and 6.34.6 not report data ( TX power, RX power, ... )
In version 6.30.4 work good.

Thanx for fix

Martin Cerny

moly

Hi, After the expansion of IPv6 in our network, we encountered a problem with the occasional break-up of OSPFv3. For example, when the router reboots or a failure of lines, it will stop the router to work with some neighbors in OSPFv3. Flapping in ExStart, Loading and 2-Way state. Usually just shut ...

moly

Will be available 48V 802.3at to passive 24V Converter with Gigabit ethernet?

Thanx

Moly

moly

We use one router (x86 ) as an aggregate and on it we follow all traffic. Make also NAT and Firewall. Simple queue use in tree mode, in top of the tree, first level is global queue, its parent for all segment queue, with limit of maximum internet capacity like 1024Mbps. In the second level is segmen...

moly

I try instal rc5 on my border router. from 5.22. After reboot, router go up, but configuration configuration seemed to be not loaded. If I try command /interface print or /ip ad print , no response, command line froze. If I try /system resource print , all is ok. Sup-out cannot be created, same prob...

moly

Hi, I try in lab from 5.22 to 6.0rc5 and 0.0.0.0/0 is not added. Tonight I'll try to upgrade our border router, where we have about 1500 queues. Ok here's what I'm seeing. Going from 5.22 to RC4 with Simple Queues, RC4 seems to add 0.0.0.0/0 as a "secondary" IP address on the simple queues...

moly

Router HW : Gigabyte EP45-DS4 , CPU Q9550 , 2G RAM , 2x Intel dual port NIC , 2x intrgrated realtec NIC

IMAG0360.jpg

moly

After upgrade from ROS5.20, router don't boot with error Kernel panic . Picture attached. Try upgrade from 5.20 with configuration and from 5.20 without configuration, result is the same. Netinstall for ROS 6.0b3 not work, try on 2 various PC. Router HW : Gigabyte EP45-DS4 , CPU Q9550 , 2G RAM , 2x ...

moly

I have 1500 simple queues i router.
Hi moly. Do you have latency and slow network issue when simple queue reaches over 1200?

Hi, no, only unexpected reboot or freeze once a 10-14 day.

moly

I have 1500 simple queues i router.

moly

I have the same problem. My configuratin : MB - SUPERMICRO X8DTH-iF-O CPU - 2x INTEL Six-Core Xeon E5645 RAM - 2x KINGSTON 2GB 1333MHz DDR3 ECC Reg CL9 DIMM SR x8 w/TS Server Hynix B NIC - 2x INTEL Ethernet Server Adapter I340-T4, 4x RJ-45 Previous router was : MB - Gigabyte GA-EP45-DS4 CPU - Core 2...

moly

I agree, it would be appropriate.

moly

thank you very much

moly

Code: Select all
/queue/simple/move
=.id=queue1

But, I need two variables. Queue whitch I need to move and Queue where I want to move ahad.

in console is :
/queue/simple/move "queue to move" "destination queue"

Thanx

moly

Hi, it is possible to make function /queue simple move in API?
Please give me syntax.

Thanx

moly

I found error in read function. Problem with length calculation. This function work fine. function read($parse = true) { $STATUS = socket_get_status($this->socket); $RESPONSE = array(); stream_set_timeout($this->socket, 2); while (true) { $tmp = ord(fread($this->socket, 1)); if ($tmp < 0x80) { $LENG...

moly

Hi, I have the same problem. I try 3.15 and 3.19. Error print : !re >>> [8, 24] =.id=*19 >>> [9, 14] =comment= >>> [9, 4] =name=VPN >>> [128, 719] �=target-addresses=10.1.1.222/32,10.1.1.223/32,10.1.1.224/32,10.1.1.225/32,10.1.1.226/32,10.1.1.227/32,10.1.1.228/32,10.1.1.229/ >>> [51, 667] 2=dst-addr...

moly

Hi, I receive some information on ubiqiti forum. Power offset may be same as the "R52H". http://forum.ubnt.com/forum/viewtopic.php?t=5175 Good power control is important for copliance telecommunications condition, in my country is maximum EIRP 30dBm for 5,4GHz. We use hi gain antena an low...

moly

Hi,
have some one experience with MB based on Intel P45 with ICH10 ( like GA-EP45-DS4 ) and ROS on CF-SATA reduction?

Thanx

moly

Thanx, I send question to Ubiquiti. I don't need it for high output power, but for very good RX Sensitivity and standart size. For longer distance I use DCMA-82, but this is bigger and in one routerbord is possible insert one, may be two. There`s not so space in miniPCI. As soon as I receive answer,...

moly

Hi, I have new Ubiquiti UB5 minipci card and test it in network. And have litle problem with power regulation, If I set 14dB or more, all is ok. On remote side i have -60dBm. If I set 13dB or less, link is disconnected, and on remote side I see siganl -90dBm. I try ROS 3.15 and 3.17 and 4 UB5 card, ...

moly

I use in router CM9 or R52 , and as client Ovislink WL-5460AP.
what mode are you using on that Ovislink client?
Make sure that you upgrade the OvislinkAP to the latest version.

I use Firmware Version: "5460APv2_e10_b1" and mode "Client-Infrastructure"

moly

I use in router CM9 or R52 , and as client Ovislink WL-5460AP.

moly

Me too. RC9 and RC10 , all bad.

moly

ok, i send supout and mor info, thanx

moly

but, my clinet not have 00:00:00:00:..... Have real MAC 00:4F:62:....... , but in registration table is wrong, and also interface "unknown".

moly

3.0rc4 on RB333

moly

Some screenshot, upset in registration table, and normal latenci in idle, no trafic.

moly

Hi, help me, i have RB532 and CM9 card as AP and clinet Ovislink WL-5460AP. In version 2.9.x its all great, high thruput and low latency. If upgrade to 3.0xx, all is bad. Thruput abou 700kbps and ping about 300 - 1500ms :( . The same problem with NTB HP compaq. I testing the new RB333 and its suport...

moly

I have the same problem with CM10. But in version 2.9.11 work fine. Now I have 2.9.25 and power control is not good.

moly

If I set TX power to 10dB , all is ok (opposite side have RX signal about -60dB). If I set lower ( 7dB ), RX signal on opposite side fall down (RX signal -90dB). If I downgrade to 2.9.11, this trouble isn't here. All work well. Where is problem?

moly

I have the same. In version 2.9.7. Sometimes in OSPF neighbors table stay neighbor router i init state and ospf connection not working.

moly

I use Atheros CM9 and if I activate encryption my CPU usage goes from 25% to 50% with the same load on Wireles card. On atheros page is writen - " Standard (AES), Temporal Key Integrity Protocol (TKIP) and Wired Equivalent Privacy (WEP) without performance degradation ". It is normal? I us...

Search found 44 matches