MikroTik

pospanko

Tha main problem, I think, is that type is defined on bridge instead of port. I should be able to set Q-in-Q on port, not on bridge.

pospanko

sfp28-1 is connection to main switch. There is no untagged traffic. All VLAN's are going from and to that port

pospanko

This is all of my config except management port and address...Am I missing something? /interface bridge add name=bridge vlan-filtering=yes /interface bridge port add bridge=bridge interface=sfp28-1 add bridge=bridge interface=sfp28-11 pvid=10 add bridge=bridge interface=sfp28-12 add bridge=bridge in...

pospanko

Hi I'm using CRS518-16XS-2XQ and I just can't get make my setup to work right... I wan't classic switching, only L2 This is my current setup on Huawei switch: Incoming port is trunk with VLAN's 10,20 and 30 Port with VLAN 10 is access. Port with VLAN 20 is trunk. Port with VLAN 30 is dot1q-tunnel My...

pospanko

Great. Thanks.

pospanko

Yes I did that. But last mentions are that BGP isn't working well. Last is mentioned for 7.3. I just wanted to check if anyone tested with latest releases.

pospanko

Hi all

Can someone update me on BGP status on 2004?
Should I use them or stay on 1072? I need tu support 2 full BGP tables. Around 20Gbps of traffic.
Thanks

pospanko

Hi I'm trying to log current interface traffic - current usage. This is my script: :if ($Traffic) do={ :foreach id in=[/interface find] do={ :local output "$[/interface monitor-traffic [find where .id=$id] once as-value]" :set ( "$output"->"script" ) "traffic"...

pospanko

I was wondering if MT can evenyl distribute 100.64.0.0/10 to 1024 addresses so I don't need to make multiple rules: Example: chain=srcnat src-address=100.64.0.0/10 action=netmap to-addresses=192.168.0.0/22 If it can't I need to write it like: chain=srcnat src-address=100.64.0.0/24 action=netmap to-a...

pospanko

Hi guys.

Is it possible to netmap 100.64.0.0/10 to X.X.X.X/23 or /22 in one rule?
Thanks

pospanko

Hi! I'm using fasttrack on few of my routers and it works well. But on one of mine CR1072 it just stop working after some time. Fasttrack connection rule counters are getting hit but dummy rule just don't show any traffic is passing through it and my CPU raises dramaticly after it stops (which is no...

pospanko

Getting the most performance out of a CHR (in my case , two CHRs on a single physical computer with two Intel Xeon CPUs (10 cores each) with Hyper-Threading disabled) OK - so I have been blabbing quite alot about CPU cache. Well , here is another trick to get even more out of a couple of CHRs runni...

pospanko

Did anyone try this?
Thx

pospanko

Hi!

I have problem with update statements with DHCP accounting. I'm using 6.43.4 and I'm always getting 0 for acctinputoctets and acctoutputoctets.
Is problem with that version or my setup... Is there anything else that should be enabled?
Thx

pospanko

Is that total throughput or per queue? I would like to use simple queus or queue tree per user, up to 600Mbit...
What do you recomend for Hypervisor?

pospanko

I would like to shape users on that CHR. Mangle based on IP and Queue tree. Is it possible?

pospanko

Anyone on other topics?

pospanko

Ok, x86 or CHR, there will be small difference. Lets say we done this part of my question.
Much more important thing is: Is it capable of shape that amount of traffic?

pospanko

Until x86 is dead look at CHR

How do you mean 'x86' is dead? I see packages in download.
My main question goal was more about HW then SW...

pospanko

Hi all! I need your opinion of what to use for shapening user bandwith of total 10G throughput? CCR1072 can't handle that, not even half of it. We use lots of them currently but is hard to maintain. Is x86 way to go? How do you do load balancing and failover? Do you use DHCP or PPPoE? Simple queues ...

pospanko

pospanko

One joke:
For you, NV2 have significant improvements too

pospanko

This is one of the stupidest answers you wrote. 60GHz is problematic on rain/snow as you probably know. 5GHz backup is not option, it is needed. Maybe would be better to listen to the customers who actually buy your equipment then to make conclusions by yourself? Maybe to ask your customers what th...

pospanko

Ignitnet 60 ghz solutions have the 5 GHz for backup I hope that MIkortik in near future develope a similar solution For that price, why not just put a second link with a couple of SXTsq Lite5? This is one of the stupidest answers you wrote. 60GHz is problematic on rain/snow as you probably know. 5G...

pospanko

The perfect product for the 60Ghz, would be a point-to-multipoint solution, clearly with high gain CPE antennas for distances up to max 1km. Possibility to connect up to 50/60 customers on a single cell Channels smaller than the 2000Mhz (1000Mhz or 500Mhz) TxPower increased to 20dB A integrated fai...

pospanko

What are we talking about? 40Mbps total? We are in 2018 !!!
We need at least 40Mbps per user offered and 150-200 aggregate per AP. Smart nv2, sync, better cpe, spectral scan etc...
No major upgrade to wireless since 2013. 5 years ago.
Just not enough this days...

pospanko

Do you maybe use bridge?
We have dramatic falling apart at 2Gbps on CCR1072 using RSTP. When we set everything to STP traffic started to run normaly. Problem was that hosts table was falling apart, losing records. Of course, no support response from MT...

pospanko

pospanko

Milestone for Mikrotik. One p2p link 80/20 works nice. Soon test p2m.

What's throughput difference for dynamic and 80/20 ratio?

pospanko

Hi everyone! What real throughput do you get for your users with MT equipment? We have 20-25 users on 20MHz, and up to 50 on 40MHz channels, but real throughput are very low. We can't get more then 40-50Mbits total on AP, and more then 10-12Mbps per user on normal AP operation and in medium interfer...

pospanko

We just installed app and I think that you are, again, going in wrong direction... This app is good for someone, and for us in long terms, but... You always miss the point. I, and probably most of people here, wouldn't use winbox on phone, what you are trying to achieve. We need phone apps. Basic fu...

pospanko

I'll start sending invoices to MT for extra cost I have because we don't have this

pospanko

Any news about this?
I would like someone come from MT to my company and try to check links as i do last few months. Without spectral scan we are doomed. It's major tool for us. You should implement futures like this even before putting new chipsets to market.

pospanko

Hi! I'm doing src-nat to public IP and I have a calculation problem. I'm trying to calculate in which PCC rule will my IP ends. Example: ... add action=src-nat chain=srcnat out-interface=XYZ per-connection-classifier=src-address:128/51 src-address=10.53.0.0/18 to-ddresses=172.16.0.51 add action=src-...

pospanko

Hi! Does anyone else experience lag problems with new Dude server? I have 1000 devices in Dude and it's very CPU intensive on CHR. One core goes up to 100% and than Dude client freezes. I'm trying it on Hyper-V VM with 4 cores and enough memory. On that config I was running Windows server with Dude ...

pospanko

Hi! Does anyone else experience lag problems with new Dude server? I have 1000 devices in Dude and it's very CPU intensive on CHR. One core goes up to 100% and than Dude client freezes. I'm trying it on VM with 4 cores and enough memory. On that config I was running Windows server with Dude and lots...

pospanko

Any changes on this? Does VPLS tunnels work somehow in Totally stub areas?
thx

pospanko

Because I have clients which are using my system and I don't want to give them all of my "magic". They need access but I don't want to allow them to see all. Main problem with MT is that user management is very poor. You can't grant specific thing to specific user - that's the main problem.

pospanko

To decrypt the script means RouterOS needs decryption key. And if this key is inside router, anyone can get it. Yes, this may be accurate, but... if I need to enter password when deploying encrypted script and RouterOS encrypt if with some special key (serial-number, licence key or sometnig), scrip...

pospanko

Let's say that this is my simplified network configuration: http://i57.tinypic.com/v5inme.jpg I am connected to two ISP's. I use BGP, but I'm taking only default route. Area1 and Area2 goes via one provider, and Area3 and Area4 goes via second provider. I only want to have backup routes. So if one p...

pospanko

I meant on not so stubby area.

pospanko

Hi all!

Which is better place to have all gateways? In backbone area or to create NSSA and put GW in them?
Thx

pospanko

Hi all!

I have AP (let's say Omnitik) on some house and I need to connect user which is 20m away? I get signals from -35 to -40. What do you do in situations like this one?

BR,
M

pospanko

Is anyone tested nstreme from v6.7, when they updated it? I got some good results lately.

pospanko

Khm,,, Unfortunately I can't use RB411GL because of low MTU - I use MPLS/VPLS. I could use RB711 but they are discounted. Now I'm like fish without water...

pospanko

okay I have had the chance to swap all our 912 boards for our usual 411gl board setup. In 3 cases we had links > 30km with ccq's all over the place and typically less than 80%. With no other changes other than the routerboard (912 to 411gl) we are now at solid performance, 99-100% ccqs, and no ethe...

pospanko

I have same problem on my network. But now I think it's related to RB2011. If I do BT to RB2011, over two wireless NV2 links, I get full throughput. But I get more then 50% lower values if I BT to router which is connected to RB2011 over Ethernet. Both UDP and TCP. There is a major problem somewhere...

pospanko

Hi all. On some CPE SXT's I have strange problem after some time. I add frequencies manually to scan-list (ex. 5180,5200,5220,5240,5260...). They work normally and after some time they disconnect and I can't 'see' AP on scan any more. If I remove all frequencies and add only AP frequency I can conne...

pospanko

Maybe I didn't formalize question good,,, Picture in attachment,,, One of my routers (C), which have gateway connected to it was at area1, not on backbone. I moved p2p link (C-B) and connection from A-B from area1 to backbone area. I expected that all networks, which are connected to router A would ...

pospanko

Hi all! Yesterday I changed few thing on my network, I added my default gateway router to backbone area, and default route wasn't propagated as I expected. On that router I also have few links which are assigned to area1. I moved my backbone link and loopback interface to backbone area and then my p...

pospanko

Is it possible somehow?
I have IP address on a page, is it possible to click on icon and run winbox to that device?

pospanko

It's very similar board. AH version have better/faster CPU. Depends what your requirements are. Probably both would satisfy your needs.

pospanko

Using it in my production network without problems. Of course, Only Mikrotik supports this. That's the only limitation Is this usable in production networks? Where's the catch? BR, M Routing a /32 via another /32 has been used for years in Telco DSL networks on a multitude of vendor equipment like ...

pospanko

Hi.
Just curious, what would you choose if you were starting new wisp. Which authentication service, which routing protocols, which equipment etc.

pospanko

Thank you for your reply and help .
Problem solved . Link up with 160 Mbps Throughput non stop .

Thanks to all

How did you solve the problem?

pospanko

I have 3x of them on stock and I must use them.
I'll give him a try and hope that it will be enough for some time, until I buy something better.
I'll get full table from one peer and I'm talking about 100-150Mbps of traffic. Hope it will work,,,

pospanko

What kind of problems you have with TE?

pospanko

I would skip using an actual /31, and just use two /32s. Specify the remote address as the "network", and you should be good to go. This mechanism is more flexible than using /31s, as the addresses don't need to be adjacent; and more efficient since you can re-use the same address for mul...

pospanko

Is it possible?
Is it fast enough?

pospanko

this feature has been accepted as a possible feature by devs for some time now, all is left - wait till it gets implemented. Unfortunately, it is not that trivial as it might look and will bring other changes to safe-mode as it is. Thx for info. Waiting for implementation. Lots of things would be e...

pospanko

It would be great to be able to enter safe mode from API before updating settings. It shouldn't be so hard to implement!

+1

pospanko

Mikrotik, it would be nice feature...
I think it's not so hard to implement. You have all facilities for that, just add command.

pospanko

Yes. This happens.
But happens on RB450 and RB2011.
On RB411 and RB1100Ah I didn't manage to reproduce this, export on them works just fine.

pospanko

Anyone have any idea?

pospanko

Hi all. I just started with MPLS/VPLS and I noticed that I can't get my tunnels up and running. Then I started with traceroute and I found that I can reach routerD from routerA via MPLS (trought RouterB and routerC) but from routerD I can't reach routerA. There is only normal trace, no MPLS. I use O...

pospanko

Hi all. I noticed that all of my EoIP tunnels every 20-30 seconds get high data rates of data at same time. Actual data is around 80Mbps, and you can see that in this moment it shows around 200Mbps on all EoIP tunnels- Picture: http://img855.imageshack.us/img855/8755/problem3y.jpg Does anyone have t...

pospanko

Anyone?

pospanko

I talked with Edmunds about this last year in Warsaw.
Company like MT should hire professionals to record MUM events.
To have multiple cameras, video director, sound technicians...
It is sadly that good lectures are wasted because of poor video.

pospanko

Hi! I have problems with my bridged tunnels. I bridge ether and wlan on CPE, bridge wlan and EoIP tunnel on AP and I created hotspot over bridge which contains all EoIP tunnels at my central location. I use horizon=1 on bridge in central location. Problem is that ping from CPE rises every 30 seconds...

pospanko

Anyone have idea?

pospanko

Hi all! I have problem with VLAN traffic in bridge. Currently my network setup is like this: CPE: ether and wlan in bridge AP: wlan and EoIP tunnel in bridge (wlan have horizon=1 and EoIP have horizon=2) Central location: Bridged EoIP tunnels and Hotspot on bridge(I use horizon=1 on every interface ...

pospanko

This has been covered many times. It all depends on your requirements If you can wire each ap to a central switch, simply set the ssid the same on all devices, but change the channels so that neighboring aps are at least 5 channels apart. Your device will switch aps as you move around the building....

pospanko

Mail on your page isn't working... Can you send me your contacts?

BR,
Marijan

pospanko

Any suggestions?

pospanko

Hi all! I have outdoor 24V UPS's (MW SCP series power supply with 2x 12V accu) which have temperature compensation. When there are very low temperatures, my output voltage go above 30 volts and my boards stops working. First RB450 goes down and then everything else. Voltage can go up to 32-33V on -2...

pospanko

Hi, I'll try to give more information about my network. I plan to do this because of future expansion and high availability. On picture, which simplifies my core backbone but for this lets take it as it shown, you can see 'my plan': http://img405.imageshack.us/img405/8941/networkyx.png Current situa...

pospanko

Hi all! I have network which have gateway on my central location. My network is spread about 40 km wide so I think to put some other gateways at both ends of my network. Is this wise? Or to stay on only one location? I currently use OSPF on my network and static routing on my gateway. If I put other...

pospanko

Hi!
You have option 'called-station-id' in radius server which identifies hotspots. It's hotspot name. You can identify it by this.

pospanko

You could use Tools->Torch to see what is happening on your interface...

pospanko

Does anyone have any idea? Thx

pospanko

Yes. I'll go with Intel model for software releases. They one year go to better production process and next year they go to architecture upgrade keeping production process the same.

In MT way it would be:
6.0 - New features
6.1 - Bug fixes
6.2 - New features
6.3 - Bug fixes
etc...

pospanko

Hi all! I have little problem and I'm not sure how to solve it. My network is routed. My current configuration is: CPE: ether and wlan are bridged. wlan is set to station-bridge mode. AP: wlan and EoIP is bridged. EoIP is going to my central location where I have central hotspot. Now, I want to reco...

pospanko

Anyone figured this out?

pospanko

In winbox on bridge interface just add Admin MAC address.

pospanko

Hi Mikrotik, nstreme is great protocol in comparison with nv2(when nv2 is better for ptm), to build low latency ptp links. Also dual nstreme. But problem is that they dont work on N cards. Do you plan to solve it? What about v6 - is possible to work there? Agree. nstreme is terrible on N cards. If ...

pospanko

I have multiple Mikrotik Board where i am getting that after some time it is getting 10Mbps & Auto Negotiation is not working, can any one suggest me the reason of it as well what is the solution of it This happens to me also. Near FM towers or far away from them. Problem is when my 1000mbits l...

pospanko

No one have high CPU utilization for ethernet on proxmox?

pospanko

MetaRouter won't boot on RB450G...

pospanko

Hi all!

I have very high CPU utilization when using old MikroTik RB44G card in proxmox. I added it as Ralink card to mikrotik VM.
Does anyone have same problem? What am I making wrong?
Thx

pospanko

I don't understand your question. Can you make it again using other words? Sorry for my poor english.

Enviado desde mi GT-N7000 usando Tapatalk 2

Do you use this card with Mikrotik installed on hardware machine or in virtual machine like I do (proxmox)?

pospanko

I use a quad port intel pro 1000 with no problems

Enviado desde mi GT-N7000 usando Tapatalk 2

Do you use this card in proxmox or...?

pospanko

I tried old RB44G and I have high CPU utilization on ethernet in profiler and packets drop.
I use HP ML350G5 with Xeon 4505 (Quad-2GHz) and it's much slower with this card then RB1100AH.
Is it because of virtualization (Proxmox) or because of ethernet card?
Any ideas?

pospanko

But of course, our own http://routerboard.com/RB44Ge

Of course

I was on vacation and I missed this.
Thx Normis.

pospanko

Hi all.
Curentlly, what is best quad NIC for MT? Thx

pospanko

But I think you should consider replacing RB450(G) with something else (RB2011 or something like that) because of RB450's MTU od 1520. You need at least 1526 fall trought your network for PPPoE over VPLS.

pospanko

In this topic and all otheres like this, everyone is talking how much costumers can be on one interface (30 or less, 50 max, etc...). No one is talking about bandwith we need to give to our costumers per interface. I can have 200 costumers with 1kb of speed on one antenna and also I can't have 10 co...

pospanko

According to the wiki nv2 potentially has lower latency (or at least more tunable) than nstream?

http://wiki.mikrotik.com/wiki/Manual:Nv2

Nstreme is still the way to go in p2p setup (latency 1-2ms).
NV2 is good for p2mp but still ping vary too much.

pospanko

Maybe you could wait for new MT beta3 which would have new linux kernel with Hyper-V support integrated inside, so you could use normal network adapters instead of legacy ones and everything should work out-of-the-box...
I really hope that this will work because I also need Hyper-V support for MT,,,

pospanko

Normis, is there a chance to add radius accounting message in DHCP? thx

pospanko

Hi, Why is this? I have my central routers at NOC. I use EoIP to my central router and there I bridge them and create hotspot or PPPoE services. I put MTU to 1450 and I can't get normal speeds in my setup. If I use same network and use hotspot login instead of PPPoE, I get speeds I set in queue at c...

pospanko

Any plan to divide:
NV2 for P2P with lower latency
and NV2 for P2MP ?

NStreme doesn't work well any more so NV2 with P2P mode would be great!

pospanko

Hello all, I have a RB433AH configured as a hotspot server and I have enable Login By Cookies in the Hotsport ServerProfile. After every first time successful login of a user I can see that a cookie is created, but oddly in all the cookies, the expiration tieme is the same and countdown simultaneou...

pospanko

Surely your reports are appreciated, but I suggest you to look at the forum again few more times. This issue has been discussed in at least two threads and there are also some feedback that you seem to be looking. I'd gladly throw you some links, but currently I'm writing from my phone and since Ta...

pospanko

MimiFlex, you have to wait for the next 6.0beta3 release.
when it will be released there will be line in changelog,
*) upgraded drivers and kernel (to linux-3.3.5);

Small digression...
Any plans to implement kernel 3.4 when it came out. There would be synthetic drivers for hyper-v...

pospanko

Hi all! We try to use Mikrotik as router and DHCP server. Switches send DHCP packets to Mtik, Mtik make req to Radius server and receive dhcp pool name, speed limits... All work good, but small problem.. No accounting :( And i don't know IP address of user (from pool), traffic. And don't know when ...

pospanko

what i mean, is to be able to create dynamic rules instead of static ones. so we could avoid unnecessary writes to the NAND disk that's not how it works, all RouterOS configuration is stored in memory, and is written to NAND after some 5 minutes. This is why you will lose config if you power cycle ...

pospanko

I use VPLS for a long time now with PPPoE to a core PoP. Works great.

What is your MTU?

pospanko

why does you centralize pppoe server instead of activate pppoe server on each access point ? I have same setup. I use EoIP but planning to go to VPLS. I have my network routed with private IP addresses and I don't want that my customers see my internal setup and I want to have everything in one pla...

pospanko

Code: Select all
/interface bridge host print

Yes. But I must search in bridge hosts for MAC address. Ok, it's a solution. I'll write some API script to get this information joined together.
But, problem is that I can't send that info to radius server in this case. I love to have this info in radacct table.

pospanko

Hi, I can see interface, on which user is connected, at hotspot hosts if I enable "Use IP firewall" in bridge. If I turn this off (whic MT recomends) then I can't see this information any more, instead there is "unknown". Is there a way to see this without "Use IP firewall&q...

pospanko

Hi pospanko, have you ever tried Telnet/mac-telnet from a ROS. When you telnet other ROS, a window opened within Winbox, so is that possible to connect it via Winbox like Telnet inside from winbox. Hi, And yes. I do this all the time. I think that it would be very helpfully that we can open winbox ...

pospanko

I think that he want smething like right click on wireless teble and then Winbox instead of MAC telnet to other router...

pospanko

+1 from
Also, more integrated devices like sector antennas (with plastic and metal case), higher gain sxt, sxt with better shilding etc...

pospanko

MT, when new version will be available? Would there be new version?
Thx

pospanko

Yes, My antennas are just one meter from FM antenna. Anyone else have some advice?

pospanko

Does the status tab on the Ethernet interface show that it is connected at a higher rate then 10bt? Is it taking errors?

Hi. No, status show 10Mbps rate (auto negotiation) and no drops or error packages. If I set ethernet to 100Mbps with auto nagotiation turned off, link doesn't come up.

pospanko

I would do a bandwidth test between each interface. I would determine the throughput of the wirelss link without consideration of the Ethernet link and the Ethernet links without consideration of the wireless link. I would suspect that you will find that the issue is either a bad power injector or ...

pospanko

Hi all.
I have problem on the tower where my equipment is set up. About 1m from my equipment is FM radio antenna (93MHz) and I can't get ethernet speed more then 10mbits. Everything is grounded well. Any sugestions?

pospanko

Ok, if you want to keep exactly the same billing system you would have to isolate CPE monitoring IPs and client bridge. First thing that comes to mind is creating separate VLANs or EoIP tunnels. I'm guessing VLANs would be easier solution since you wouldn't have to add IP addresses for EoIP termina...

pospanko

Ok, if you want to keep exactly the same billing system you would have to isolate CPE monitoring IPs and client bridge. First thing that comes to mind is creating separate VLANs or EoIP tunnels. I'm guessing VLANs would be easier solution since you wouldn't have to add IP addresses for EoIP termina...

pospanko

I want to reconfigure my network so I can access, benchmark and control my CPE's (so that I have full speed access and users just speed I gave to them) but to keep them simple with as low as possible config on them. Any suggestions? Is there any reason why your CPEs are set to bridge besides "...

pospanko

i do not have an hotspot in each cpe my cpe are routed: wlan in station, and nat-masquerade. in this mode users cannot access to the dhcp server of the ap my mtu is 1472 yes, i plan to use vpls infew weeks Thx for response. Yes, I understand the way your network is designed. I must get rid of hotsp...

pospanko

my network is routed. cpe connecting to access point receive in the vlan an ip from the AP pool the ap bridge the wlan and an eoip tunnel. the eoip tunnel is terminated to a concentrator with a pppoe server (not an hotspot) the cpe receive a public ip via the pppoe client then give to the customer ...

pospanko

How do you setup your network? How do you use CPE devices? Do you use tunneling? I'm talking about routed network via private address space.
Thx

pospanko

RB1100AHx2-5Hn

Good one

pospanko

your custome connect using pppoe?

No, my costumers use hotspot access. But I want that my users go direct to central server location, not to go trought my routed network. Because of that I use tunneling.

pospanko

Anyone?

pospanko

Hi.. what type of routers ? RB1100 ? or RB112 ?

Probably RB1100AHx2

pospanko

wlan1 could belong to bridge and be reachable directly if it has an ip I already tried that. Added IP to wlan on CPE + default route and IP to wlan on AP. Sometimes it works, sometimes not. Probably because of bridge. With that setup, I can ping CPE, then I get few timeout, then few pings, then tim...

pospanko

you must assign an ip to each cpe. use a dhcp server on every AP (linked to the wlan) and pass to the cpe the ip and the default gateway (the ap itself) I'm not shure how would this help me bacause all my interfaces are in bridge or you suggesting to remove bridges? I need to "preserve current...

pospanko

is this a Routed network or a bridged network.

Routed. Because of that I use EoIP tunnels.

pospanko

Hi all, I have some questions about monitoring and controlling CPE devices. My network is routed with OSPF and I have lots of EoIP tunnels coming from my AP's to my central location. On every AP, EoIP is in bridge with wireless interface. CPE devices are in "station-bridge" mode with wlan ...

pospanko

+1 to ATPC also

pospanko

ROS6 alone would not help. It does need complete new hardware. UBNT failed to do this with SW. MT has to go the path of going deeper into wireless chip design. Not sure this is what MT is willing to do as it will increase pricing. Yes, that is correct. But they could create it like add-on for Route...

pospanko

I have this problem on all of my routers. It should be fixed in 5.9. But if you upgrade from earlier version, there could be setup messed up. Just try to reboote device, don't change enything. Everything should revert to normal.

pospanko

Thank you so much blake for your command. I have 4 SXT which 3 of them connect to the same VLAN 185 and 1 SXT connect to VLAN 187. What should i add mac address of WDS ? . . . /interface wireless wds add master-interface=wlan1 disabled=no name=wds1 wds-address=<Subscriber MAC> add master-interface=...

pospanko

You can cache youtube like content via using 3rd party PAID Addon for SQUID name VIDEO CACHE . I will not recommend you to Cache Youtube , it's not worth it and you can't actually cache even 1% of YOUTUBE , imagine how much space you will be needing , grrrrrrrr :p, Also there are very slight chance...

pospanko

i have solved it. you can contact me : kishor(at)parasoninfo.com Forum is used to share information about how someone somehow solved some problem. I can guess that you found dozen of answers here, on forum. Now imagine that everyone left only "Yes, I solved it. Contact me if you want and if I ...

pospanko

Yes, this would be great to have! +1 P.S. Add to hotspot profile - "Incoming/Outgoing packet mark" two more mangle rules. Not only packet marks but also a connection mark before them and use that conneciton mark for packet marking. This would make my life easier and my router would finally...

pospanko

RB doesn't have battery to keep date and time so only way to have it right is to use NTP client to synchronize your RB against NTP server (Or you could always set it up manually

)

pospanko

Winbox is still the number one tool for us: - Router is searchable/configurable without knowing/changing ip-configuration - It behaves much better/faster than a web based interface and runs fast even on slower laptops Would like to see a Android Winbox app. Agree with everything especialy Android r...

pospanko

Hi, I manage to start it up, but now I have lot of inputs in my syslog: Examle: Oct 25 16:17:43 videocache1 kernel: [11554.750031] via-velocity 0000:04:09.0: BAR 1: set to [mem 0xfe902000-0xfe9020ff] (PCI address [0xfe902000-0xfe9020ff]) Oct 25 16:17:43 videocache1 kernel: [11554.790053] via-velocit...

pospanko

Hi, You could use

/system shutdown

command before you power it off.

pospanko

I think that this topic moved away from memory problem. Problem is why does single queue, of any kind, use 6MB of memory? I'm thinking about purchasing SuperMicro server for my core routing so I'm interested in any problem I could expect. So, let's go back to issue posted by kjasko. And why only one...

pospanko

Hi,

I just can't install it (I can't see it under ifconfig -a; kernel 2.68.35-11). I'm only basic linux user so any help would be appriciated. Beside this, there is problem of finding linux drivers for this card. Can enyone help? Thx

pospanko

E450 is newer. It should be slightly faster than similar Intel Atom models.

Yes, but I don't have Atom tests also, so...

Maybe sameone did some tests and comparations to RB's? Where does Atom and Zacate fits, between whic routers 450G and 800, or maybe they are faster, or slower, or...

Thx

pospanko

Hi,

did anyone tried AMD Dual-Core Zacate E350 as router?

pospanko

That's much better information. If you're good with buying and reading some books (which I'd recommend) I'd suggest "Top Down Network Design" from CiscoPress. Ignore the vendor specific information, the ideas in the book are excellent and apply to any network. If you are looking to be sca...

pospanko

Hi all. I see that this conversetion is quite contrary... Yes we need GPS Sync, No we don't. I think that any new feature is good if product price remains the same (or just a little higher), so the solutions for both sides would be that MT implements Sync in separate device (like RadWin) or create i...

pospanko

Hi normis,
How to select the MMCX port where I am to use the Omni Antenna?

In single chain mode, always use chain 0. Chain 1 is only for dual antennas.
You have this options in wireless interface form, under HT tab.

pospanko

Anyone?

pospanko

Anyone?

pospanko

Hi, I have lots of EOIP tunnels coming to my central location from my APs. All users have RBSXT as client device set in station-bridge mode. My problem is that sometime some of my users can't get login page. They have regular IP with correct gateway and DNS but no login page appears. They have valid...

pospanko

Uf, my mistake. I didn't add those addresses in networks, they were redistributed as connected. Sorry and thx for help.

pospanko

It depends whether route is advertised as external, whether it is in the same area or in different area etc. I put two ranges on ABR for that area. One for links between devices and second range for loopback interfaces. First are /30 addresses (summarized as /19), second one are /32 (summarized as ...

pospanko

Hi, Maybe I'm making mistake, but my /32 addresses, which I use for loopback interfaces, aren't summarized. Other routes are summarized as they should be, but this ones are shown in route table accross network as they are. I'm tried with version 5.4 and 5.6 and problem is the same. I tried to change...

pospanko

Hi,
Let's say:
http://www.i4wifi.eu/hardened-power-sup ... d1903.html
+
http://www.i4wifi.eu/8-port-pasiv-poe-i ... d2063.html

pospanko

Hi to all. I'll try to make more sense to my central location picture. I heve lots of access points connected to my "MT hotspot" router at central location via EoIP tunnels. All authorization is done on that router. All network outside central location is routed with OSPF and there I don't...

pospanko

Anyone...?

pospanko

One more idea...
Add single 2.4GHz antenna in it for free hotspot and use 5GHz for regular customers.
Integrate it in OmniTik, put 2.4 card in it or put one mPCI slot inside so we can add card in it...
Omnitik with two 5GHz antennas, one 2.4GHz antenna, PoE on ports 2-5... Device of my dreams...

pospanko

Great thing would be to have PoE out on ports 2-5... Whats the idea whit those ports anyway? If they doesn't have poe out? They are great. You could connect more then one link or some ethernet users to it but you must have seperate powering, which is pain in the ass :D PoE would make OmniTik superb...

pospanko

Great thing would be to have PoE out on ports 2-5...

pospanko

Is ports for accounting (probably 1813) open on radius server? Is accounting enabled on radius server?

pospanko

No response...
All gurus are on vacation

pospanko

Hi all,
I have a question.
How does MT equipment works near AIRMUX or RADWIN on same tower?
Thx

pospanko

Yes, thats heplfull, but it would be a good thing to have a tool which would do what you described. I think it's not too much to ask and it would make our life easier.

pospanko

I think that second is used only when first one doesn't return response... You can't check second if first doesn't have user because first generates valid response

pospanko

Maybe sameone can recommend me some good book or article about this topic. Thx

pospanko

Yes, same here. Management goes nuts if SNMP is enebled (v5.5)

pospanko

Hi all,
I have few APs which are connected to Central location, Central service. Now I have this setup, so I need to upgrade it. Can you recommend me what to do? Whato to add, how to connect, via switch or...?
Thx

pospanko

I have v5.5 and my "management" process put my RB800 CPU to 100% every few minutes. When I disable SNMP then menagement is from 0-5% and CPU never goes up to 100%. I monitor my router with Dude.

pospanko

What are those extra LAN port for? Run multiple cable from rooftop to basement? he he he Wirelessguy I find it very usefully for AP with 2-3 links for redundancy and user ethernet connection (house or building where I place it). But, as mentioned in some other posts, PoE out on 2-5 interfaces would...

pospanko

Disable Universal client on HotSpot interface, /ip hotspot set <number> address-pool=none Khm,,, Universal client is great thing and I need it because I have lots of users with "forest of IPs", so this is not an option. or use /ip hotspot ip-binding to allow only IP addresses you want, /i...

pospanko

Hi all,

I have another problem with my hotspot. I have lot of public IP's in my host list. How to block them? I want only my clients to be there. I run hotspot on bridge with lots of EoIP tunnels.
Thx

pospanko

Khm... Ok. I was hopping that I can assign to users different pool than they get by dhcp and not to do manual bindings. Thx anyway.

pospanko

Hi all, I added address-pool for my hotspot users so I want that all of users have One-to-One NAT translation to different pool that given by DHCP. But, some of my users still have their local IP addresses, given by DHCP, as outgoing addresses in hotspot. In hosts file there were no translation. Any...

pospanko

Old topic but,,, Anyone manage to fix this issue?

pospanko

When we can expect simple queues to be fixed?

pospanko

Hi fewi, and thx for respons. Use the address list feature of user profiles to put all related users on an address list. Then use queue trees with SFQ to override simple queues. You can't do what you're trying to do with simple queues. http://mum.mikrotik.com/presentations/US10/FelixWindt.pdf Yes, I...

pospanko

Hi all,

Is there a way to create one simple queue with shared-users > 1,? So that all users which login with same account goes to one queue and share one speed limit?
Or, maybe is there any better way to do that...
Thx

pospanko

Only one possible issue I have interest in is left: simple queues/queues. Some reported a strange behaviour here... Hence my only unit not upgrade to 5.4 is my main router (rb1000) with 230 simple queues.... It still runs 4.11 and I am only upgrading is I get 100% feeling it will have no issue.. Ar...

pospanko

Id like to have several hundred monitored devices that are not on any map, is this possible?

Yes, this would be nice to have.
Also, It would be good thing that we could add same device to multiple maps with some "Add existing device option"...

pospanko

The Horizon option only works locally on the router, it does not translate over to another router. On your APs you shouldn't have to worry about placing a horizon since you have wireless interface bridged with a EoIP tunnel, as long as the bridge itself does not have an IP assigned to it, the guest...

pospanko

Anyone?

Beside that, I have one more question. Is there a way to create load balancing on another machine with failover for hotspot users?

pospanko

Hi all. I have setup like this: 2 AP's with 2 wlan and one ethernet interface for clinets (defaoul forward is off on wlan interfaces). All this interfaces on AP are bridged together with eoip tunnel which goes to my office location where i setup hotspot on bridge with two eoip tunnels comming from m...

pospanko

There's no generic answer to that question. In the lab you may be able to push 400,000 connections in the connection table by opening them up one by one and setting a high expiration timer so that the router is essentially idle. That's not a real world scenario. In the real world the router will no...

pospanko

Dear, Regarding Hide SSID in mokrotik , i have more that 30 link and all link Hide and working good , i don't have problem and when make scan i don't get it , in case i type SSID in station and when make scan i get it .... okay If you have more information im glade for help ... I have more then 100...

pospanko

have you tried to scan from laptop?

No, I didn't try that. I'm not currently in office so I can't test it, but on MT scan I see hidden ssid's.

pospanko

RB1000, not RB100. RB100 is crappy old board. RB1000 tested by us to handle up to 300 users with mppe128 encryption. But I don't know actual limitations. I think it is only CPU and Memory dependent. You can use one vrrp group for active/standby failover or you can DNS names and two vrrp groups for ...

pospanko

So, best way for me is to go with OSPF, MPLS and VPLS?
How much traffic and clients can RB100 handle? Redudancy?

pospanko

Anyone?

pospanko

RB411AH as ap-bridge and RB/SXT. Both 5.1 version.

pospanko

When I hide ssid in ap-bridge mode it is shown on client when I use scan...
Bug?

pospanko

Hi all! I have 50 AP's with hotspot access adn around 1000 clients. All addresses are private. Now I get /20 range from my ISP and I want to go with PPPoE and public addresses for current customers and privat will stay for free hotspot access. What protocols tu use for routing (now everything is sta...

pospanko

Normal, as it is. Default is H, if you turn it 90 degrees then is V.

pospanko

maybe cpu process till 100% when proxy building cache,..the solution usual im doing is disable nat redirect to proxy port.

Hi. Thx for answer.
No, I tested it for few days so it isn't in cache build. So, how do you redirect traffic to proxy? By routing it or...?

pospanko

Hi, I figured how to setup proxy to work with multiple gateways, but now I need help on how to setup tproxy,,, I just can't make it work... So, I have one interface on my Squid box and now it is working as transparent proxy. On my main MT router, i marked http traffic and routed it to proxy. On prox...

pospanko

Can anyone help me setup MT and squid to work with tproxy?

pospanko

Thanx 4 replies when the process touch to 100% ,then internet goes down !! why it goes to high ????? Hi all! I openned this topis once again because web-proxy in MT with RB is useless. I tested it on RB433AH with 8GB MicroSD and with 1 (i write it: ONE) wireless client and after few pages are oppen...

pospanko

You should only need / require TProxy in when using public IPs to customers. Since you're not using public IPs I don't see any reason to use TProxy. Just redirect them with dst-nat and define 'http_port 3129 transparent' (or something similar) for the Squid listening port. NAT Squid across the ADSL...

Search found 283 matches