MikroTik

logros

HI, i have trouble with my router, RB941-2nD periodically rebooted after upgrade to ros 7.5
in log see this:
router was rebooted without proper shutdown
kernel failure in previous boot
out of memory condition was detected.

have anyone ideas what that and how to solve?

logros

thanks

logros

Hi, i have this in log
https://prnt.sc/somztx
I changed password but have the same,
when i delete this file from mikrotik in downloaded automatically again.

logros

Have you the network card from pc or laptop a fixed IP-address?

yes.
i did all like in manual for netinstall in wiki.but no result

logros

can't reinstall? netinstall can't see board.

Can you write how must i must do this?

logros

I need help!

logros

hi, i have rb2011ls-in with 5.26 routeros, i want to upgrade to 4.17, after this procedure he don't want to respond. when i plug in cable port eth1 - eth5 start light indicator led, but when i plug to eth6-eth10 don't light. I try to restore with netinstall 5.25 and 6.7 , all step by step like in ma...

logros

thanks,
i need to check every 1 minute with script "rx-bits-per-second" value of interface and if it 0 mbit need to reconnect interface.
how can i do it?

logros

Hi, in picture i write what i need.
please help

logros

nobody knows what is this?

logros

i have four wan conections, but rb800 has only two ports in my case for wans, that i decide to use 250gs switch for wans. each port in switch has vlan1,vlan2,vlan3,vlan4 and trunk port conected with rb800.on rb800 on one port wich conect to switch, i create vlans: vlan1,vlan2,vlan3,vlan4 each has dc...

logros

thanks alot

logros

"not in local ACL, by default accept" i see this event in wirelless log, can i change default action to "drop" ?

i want that stations not in my ACL will be droped.

logros

can anyone explain my wan port every 1minute reconnect.
In log wan port down, wan link up.

Tried to change Rate of port to 1Gb, 100Mb have the same result: reconnect

logros

Halllo, again need your hint. i have 2 routers. I need to setup that rb450g will be only as border router with PCC balance without NAT function, and rb800 will be with nat, dhcp-server and firewall functions. what configuration of lan rb450g port and wan rb800 port i've must to set? http://logros.ck...

logros

Are there plans to create expansion cards for 16 Gigabit Ethernet ports for rb800?

logros

hallo all, can any one help please. i have rb800(1Gb ports)+rb816(16 10/100mb ports) 5 wans 100mb/sec for each port, connect to rb816 ports. local port is one of gigabyte ports on rb800. What is the speed of commutation and transfer between rb800 and rb816, and can i have all avalaible speed(500Mb/s...

logros

sure. use VLANs and bridge them with WANs on RB450

thanks a lot.

logros

this is scheme on rb450G has 3 wans with dhcp clients, from rb800 i need to create 3 pppoe sessions over 3 wans on rb450g respectively.

Can mikrotik do it?

logros

rb450G has 3 WAN's after it rb800 is a gateway for users.

can i create 3 pppoe conections from rb800 over 3 wans on rb450G??

logros

you don't use radius but i want to use radius)) and i need answer please help.

logros

I set up all as in http://wiki.mikrotik.com/wiki/User_Manager/DHCP_Example but can't get ip address. in log mikrotik i have "ryd16-2_err-: dhcp1: radius authentication failed for 00:22:41 :26:B9:AA: no valid profile found" what "profile" and were i must set up it i don't know. ca...

logros

you meen that i can use 4 modems connect via usb hub to rb433uah and apply PCC to load balance 3G lines?

logros

I want to use RB433UAH with 4 usb modems, how can i do it??

logros

thanks

logros

Please help need driver to this card and how to install him to RB?

logros

use both-address

logros

only this site reloaded, other social sites work fine.

logros

only this one site? sorry but in that case, most of us can't test it, we don't have an account there

I'll give you my account)) to test in PM

logros

I have RB450G and 3 wans configurated in PCC and 100 users after router.

When i go to vkontakte.ru site only reloaded and don't login.

Anyone have this problem?

logros

this setup is for wan1 and wan2. how do you use it with three lines? %) and... do you use web-proxy? In this case is wan1 and wan2 I use web-proxy enabled: yes src-address: 0.0.0.0 port: 3128 parent-proxy: 0.0.0.0 parent-proxy-port: 0 cache-administrator: "webmaster" max-cache-size: none ...

logros

with my eyes shut: /ip firewall mangle add chain=output per-connection-classifier=dst-address:2/0 action=mark-routing new-routing-mark=table1 disabled=no add chain=output per-connection-classifier=dst-address:2/1 action=mark-routing new-routing-mark=table2 disabled=no Hi again, i need you professio...

logros

thanks all ok

logros

Can anyone help me.
upload to mikrotik package 4.8 ROS reboot and after dont load anymore.
can't ping,can't winbox find by MAC.

What i must to do??Help please its very important

logros

after router rb450G working 200 machines dns servers give to machines from ISP. many poeple work well in internet, but part of them with problem: couldn't resolve ip address ya.ru or google.com.ua or others and ping 4.2.2.2 is work ok. At this moment go to firewall connections and see dns query from...

logros

any activities

logros

ip firewall nat add in-interface=Local dst-port=80 protocol=tcp action=redirect to-ports=8080 chain=dstnat
ip proxy set enabled=yes port=8080

in winbox menu ip webproxy tab connections dont see any activities

logros

/ip firewall mangle add chain=output connection-mark=no-mark per-connection-classifier=both-addresses:3/0 \ action=mark-connection new-connection-mark=wan1_conn passthrough=yes add chain=output connection-mark=no-mark per-connection-classifier=both-addresses:3/1 \ action=mark-connection new-connect...

logros

))) you are right it's crazy)))))

)))))

logros

have 3 ISP dynamic PPPoE load-balancing uplinks and 1 Lan Need Webpoxy to work in this config / ip firewall mangle add chain=input in-interface=pppoe-out1 action=mark-connection new-connection-mark=wan1_conn add chain=input in-interface=pppoe-out2 action=mark-connection new-connection-mark=wan2_conn...

logros

i have the same situation my config work but i dont know well or not :)) 3 ISP dynamic PPPoE and 1 LAN port / ip firewall mangle add chain=input in-interface=pppoe-out1 action=mark-connection new-connection-mark=wan1_conn add chain=input in-interface=pppoe-out2 action=mark-connection new-connection-...

logros

please help

logros

i have routerboard 450G Have 3 dhcp from the same ISP gateway for all wan's is 12.10.2.100 and dns 12.10.2.100 but won't work it right. all traffic goes from wan3 not balanced.((( help to fix problem / ip address add address=192.168.88.1/24 network=192.168.0.0 broadcast=192.168.0.255 interface=Local...

logros

Here is my config 3 dhcp clients ISP 1 lan but not working well. please help with this i haven't access to internet /ip address add address=192.168.88.1/24 broadcast=192.168.88.255 comment="" disabled=no \ interface=Local network=192.168.88 /ip dhcp-client add comment="" disabled...

logros

from winbox new terminal export file "filename" then you can find that file at file section on winbox. and when i ping from router write to me can find route for host I don't understand what you mean. do you mean " when pinging from router, it reply ... can't find route to host?"...

logros

can anyone help

my configuration
3 dynamic ISP
1Lan

doing all of the latest config of hli1ll

and when i ping from router write to me can find route for host

and how a can export my config from router?
thanks

logros

situation ether1 - LAN 12.10.2.0/24 ether2 -WAN1 dynamic pppoe ip ether3 -WAN3 dynamic pppoe ip ether2 and ether3 has the same gateway 193.12.248.19 but dynamic ip's i will trying PPC and others methods from wiki in this example ip is static and has 2 different gateways in my is dynamicand 1 gateawa...

logros

http://wiki.mikrotik.com/wiki/PCC#Application_Example_-_Load_Balancing just instead of 'gateway=1.2.3.4' use 'gateway=pppoe-out1' thank's :) But what arguments of dst-address in this lines i've must insert: add chain=prerouting dst-address= 10.111.0.0/24 action=accept in-interface=Local add chain=p...

logros

Hi,
i need your help.
I have 2 wan connections to ISPs dynamic PPPoE and 1 Lan port to local area.
How i can setup it right to load balancing bandwith to all users in local? Or give link's to manual "How to"

Thanks a lot to man, who help me:)

Search found 49 matches