You just make them login with vpn and that will solve your problem. Or you coulg give each of them IP, but than you are giving up on authentication and lot of control on user. Best way and we have tried everything is to authenticate via VPN.

If you are using Senao or Pheenet as client device there is problem with 2 or more pppoe connections at same time. We are solving that problem with VPN connection.

We have a stranfe problem, sometimes traffic stops towards our bgp router for 8-30s. Tried to change ethernet card but still the same result. Any idea?

We have the same problem with bridge and eoip. When we let traffic go thru that link it goes crazy and cpu goes to 100%. but with bandwith test we get 20mbps easely.

This was test one time, and we have licence for 5.4 and 2.4 in serbia and we are waiting for 900mhz. channel width was 10mhz and 5mhz.

Normal GSM 900mhz antena, at moust 2dbi gain.

We have made a test basestation with 4 yagi antenas 8 dbi pointed in all directions. Our test subject is 3.5km in house without LOS. He has signal of -88. Ping is 2-4ms, he is able to pull 4mbit constantly from our local ftp server. I think that this card is the best solution for real broadband inte...

For that kind of demand i sugest that you make sectored AP with 3 x cm9 or 3 x prism 2.5 cards with pentium at least 900mhz procesor. We have similar AP with 110 costumers.

We have solved it with pptp but i was thinking that it could be solved with pppoe.

i have tried it and results are the same.
One client is always working and second one is able to authenticate but there`s no traffic passing thru. Is there solution for this kind of problem?

Thaks will try it

We have this kind of problem: 1. If there is one user connected on our ap using senao sl-2611cb3+ delux pppoe is forking perfectly for him. 2. When we added switch on that senao and added another pppoe (another computer) bouth clients connect but only one of them is able to pass traffic second clien...

We have this kind of problem: 1. If there is one user connected on our ap using senao sl-2611cb3+ delux pppoe is forking perfectly for him. 2. When we added switch on that senao and added another pppoe (another computer) bouth clients connect but only one of them is able to pass traffic second clien...

Have you tried other freq.

If you set same freq you will make interfirance to your self. We have 6 basestations on 2.4 with that5 kind of equipment and we use 3 x 120 and same ssid diferent freq and it works great. Same thing on 5.4GHz

You should use 3 diferent freq and 3 diferent ssid because of clients. When they scan for network it is much easier for them to see witch sector is better for them than to have 3 x same ssid, it will confuse them and allso be nightmare for you.

We have tried that on our network an it works great only if one sr5 card is inserted. With 2 cards it drains too much power from board and it works poor. it`s good idea to use routherboard per sector to awoid interfirence from the cards them self, because they are too close to each other

It will not work!! We have tried it on our ap at local watertower and it had constant problems with signal and clients disconecting constantly. We changed to prism and it works wery fine. We tried to use 3 x sector antenas on 2 RB 500 and where there is one card forks great an other one const. probl...

You could try locking down your clients datarate to lower rates. It could improve your ping.

thing is "per sector" not on omni, we have tested it on omni and we could get as fa as 20 users working properly on that interface. We setup omni antena first then when neaded we setup 3 x sector interfaces and boost our bandwidth.

I would have to confirm that there are too much users on your ap try with 3 sector antenas with 3 prism`s. We have that kind of system with SR2 instead of prism and it rock`s. We have 140 user per base station and pings are 2-7 ms.

We have tested link on 3km with sr5 cards locked on 48MBit/s it gets troughputh of 53 MBit/s HD. And the signal stays the same on every datarate.

Try to set ack-timeout to 408, it could help. and try tx power to default.

I would sugesst to set the freq on SR5 5800 in turbo mode. We have tested it and mesured it and it works best on thouse freq. It transmits full 400mW.

Try using this chanels:
1. 2412
2. 2427
3. 2462

And tell me what kind of antenna are you using. 120 sector or?

Could scan for oter AP`s in area and post your results.

On what freq are those cards working?